Hunter 99814 Universal Ceiling Fan Receiver Installation
Model: 99814
Rated for ceiling fan max load of 1 amp. Rated for light wattage of max 300 watts.
The Hunter Add-On Receiver works with Hunter pull chain fans and requires a compatible transmitter (sold separately).
Hunter Fan Company Control Limited Warranty
Hunter Fan Company warrants the Control to be free from defects in material and workmanship for one year from the date of sale to the original purchaser. Hunter will replace the Control free of charge if it malfunctions or fails due to a defect within the warranty period. This warranty is void if the original purchaser ceases to own the Control. This warranty is in lieu of all other express warranties. Implied warranties are limited to the duration of this express warranty. The warranty excludes malfunctions or failures caused by unauthorized repairs, mishandling, improper installation, modifications, damage, or unreasonable use. It does not apply to batteries or damage from faulty batteries. To obtain replacement, return the Control postage prepaid with proof of purchase to Hunter Fan Company Service Department, 7130 Goodlett Farms Pkwy., Memphis, TN 38016. Hunter Fan Company is not liable for consequential or incidental damages. Some states may not allow limitations on implied warranty duration or incidental/consequential damages.
Read and Save These Instructions
This product conforms to UL Standard 1917.
FCC and Industry Canada Compliance
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to two conditions: (1) the device may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device. It generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. If interference occurs, try reorienting the antenna, increasing separation between equipment and receiver, or connecting to a different circuit. Unauthorized modifications may void the user's authority to operate the remote control.
Battery Warning
⚠️ Chemical burn hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If swallowed or enters the body, it can cause severe internal burns and death in as little as 2 hours. Always secure the battery compartment. If it does not close securely, stop using the product, remove batteries, and keep away from children. Seek immediate medical attention if batteries are suspected to have been swallowed or placed inside the body. Dispose of cells properly.
Installation Instructions
- Prepare Fan: Use the pull chains to set the fan speed to HIGH and the light to ON.
- Turn Off Power: Ensure the power is OFF at the outlet box and wall switch location before proceeding. [Power OFF]
- Remove Canopy: Remove the fan's canopy. Note existing wire connections or take a photo. Remove wire connectors from the outlet box to the fan, leaving grounding wires connected.
- Install Receiver: Choose a hanging system similar to your fan's. Install the receiver and wire as directed. Note: Installation may be difficult on angled ceilings. Call 1-888-830-1326 for assistance. Some fans may have excess wire; trim to leave a minimum of 8 inches, re-strip fan wires to 1/2 inch, and place excess wire into the ceiling electrical box. Ensure the bracket and fan remain properly grounded.
- Connect Ground Wires: Using an orange wire connector, connect the three grounding wires (green, green/yellow stripe, or bare copper) from the ceiling, downrod, and hanging bracket. ⚠️ All wiring must comply with national and local electrical codes (ANSI/NFPA 70). Consult a qualified electrician if unsure.
- Wire Receiver to Fan: Using orange wire connectors, connect the receiver's blue wire to the fan's blue wire (or black with white stripe wire). Connect the receiver's yellow wire to the fan's black wire.
- Wire Receiver and Fan to Ceiling: Using orange wire connectors, connect the ceiling's black wire (ungrounded) to the receiver's black wire. Connect the ceiling's white wire (grounded) to both the receiver's white wire and the fan's white wire. Push wire splices upward into the outlet box, separating grounded and ungrounded wires.
- Reinstall Canopy: After all wires are connected and secured, reinstall the canopy according to the fan's owner's manual.
- Turn On Power: Turn the power back ON. ❗ IMPORTANT: Use the pull chain to set the fan speed to HIGH before operation. [Power ON]
- Pair Receiver: Pair your receiver to a compatible Hunter wall control or handheld remote (sold separately) by following the instructions included with the remote. To prevent faulty operation, disconnect power from all other Hunter ceiling fans within range while pairing.
Pairing Success Note: If pairing is successful, the fan will turn ON to low speed. If a light is installed, it will flash 3 times and remain ON. If unpairing is successful, the fan will turn OFF. If a light is installed, it will flash 3 times and remain OFF.
Troubleshooting
Remote Control of Fan is Erratic
- Ensure the battery is installed correctly.
- Install a fresh battery.
Multiple Remote Issues
- If experiencing interference or faulty operation with multiple remote-controlled fans on the same circuit breaker, visit www.HunterFan.com/FAQs and click "How do I properly install multiple remote-controlled fans?" for corrective information.
M3861 01/21/21 © 2021 Hunter Fan Company
Hunter Fan Support Site and Help Center
