De'Longhi La Specialista Coffee Machine User Manual
Before using the appliance, always read the safety warnings. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
1. DESCRIPTION
1.1 Description of the appliance
A1. Beans container lid
A2. Beans container
A3. Cup tray
A4. Steam dial
A5. Hot water spout
A6. Steam spout
A7. Cappuccino maker selection ring
A8. Cappuccino maker
A9. Cappuccino maker connection nozzle
A10. Cup grille for espresso
A11. Cup grille for glasses or mugs
A12. Drip tray grille
A13. Drip tray
A14. Drip tray water level indicator
A15. Water tank lid
A16. Water tank extraction handle
A17. Water tank
A18. Water softener filter housing
A19. Power cord connector socket
A20. Main switch (ON/OFF)
A21. Boiler outlet
A22. Coffee mill outlet (tamping station)
A23. Presser lever
1.2 Description of control panel
B1. ON/Standby button
B2. Ground coffee quantity dial
B3. "X2" button: to use the 2 coffees Easy Clean filter
B4. Rinse button
B5. "OK" button: to deliver the beverage/confirm
B6. Hot water button
B7. "My" button: to customise beverage quantity
B8. Mode selector dial:
• Espresso
• Americano
• Coffee
• Descaling
B9. Descale light
B10. Steam ready light
B11. Overtemperature light
B12. Energy saving light
B13. General alarm light
B14. Beans container empty/No beans container light
B15. No water light
B16. Pressing light
B17. Pressure gauge
1.3 Description of the accessories
C1. Filter holder
C2. Easy Clean filter 1 coffee
C3. Easy Clean filter 2 coffee
C4. "Total Hardness Test" indicator paper
C5. Descaler
C6. Water softener filter (*if present)
C7. Power cord
C8. Tube brush
C9. Milk jug
2. PREPARING THE APPLIANCE
Wash all accessories with warm water and washing-up liquid, then proceed as follows:
- Insert the beans container (A2) in the coffee mill. The container is correctly inserted when the arrow is lined up with the ☕ symbol and you hear a "click";
- Insert the drip tray (A13) complete with cup grill (A11) and drip tray grille (A12);
- Extract the water tank (A17) and fill with fresh clean water, taking care not to exceed the MAX level;
- Put the tank back in the appliance.
Important: Never operate the appliance without water in the tank or without the tank.
Please note: You should customise water hardness as soon as possible following the instructions in section "12.2 Water hardness".
3. SETTING UP THE APPLIANCE
- Plug the power cord connector (C7) into the socket (A19) at the back of the appliance, then plug the plug into the mains socket. Make sure the main switch (A20) at the back of the appliance is pressed and in the I position;
- The ♨️ light corresponding to the button (B6) comes on and the ? light (B15) flashes to indicate that you need to deliver water to fill the circuit;
- Place a container with a minimum capacity of 100 ml under the hot water spout (A5) and cappuccino maker (A8);
- Press the ♨️ button (B6) corresponding to the light. Delivery begins and stops automatically. Empty the container.
3.1 Rinsing the internal circuits
Before using the machine, you must rinse the internal circuits. Proceed as follows:
- Attach the filter holder (C1) complete with filter to the appliance. To attach correctly, align the filter holder handle with "INSERT", then turn the handle to the right until it is aligned in the "CLOSE" position;
- Place a recipient under the filter holder and cappuccino maker (A8);
- Press the ? button (B4) corresponding to the light. Delivery begins;
- When delivery is complete, turn the steam dial (A4) and deliver steam for 10 seconds to rinse the steam circuit;
- Repeat points 7 and 8 until you have delivered at least 1 litre of water (about half the tank);
- Extract the water tank (A17), rinse and fill with fresh clean water, taking care not to exceed the MAX level. The appliance is ready for use.
Please note: We also recommend rinsing the internal circuits if the appliance is not used for a long period.
The first time you use the appliance, you need to make 4-5 cups of coffee before the appliance starts to give satisfactory results. Pay particular attention to the quantity of pre-ground coffee in the filter (C2 or C3) (see instructions in section "4.5 Adjusting the quantity of ground coffee in the filter"). Proceed as described in section "4. Prepare the perfect dose".
4. PREPARE THE PERFECT DOSE
4.1 Preparing the coffee mill
- Make sure the beans container is correctly inserted and lined up to position "3" (default setting);
- Remove the beans container lid (A1);
- Place the required quantity of coffee beans in the container;
- Close the lid, pressing firmly.
- The first time you use the appliance, make sure the dial (B2) is in the position (default setting).
4.2 Select the grinding level
The grinding level affects delivery speed and therefore the quality of the extract. The first time you use the appliance, we recommend using the factory setting (medium grinding), then if you are not satisfied with the result, adjust the level according to your personal taste and the type of coffee by setting a finer or coarser grinding level, referring to the tips in section "4.5 Adjusting the quantity of ground coffee in the filter".
Important:
- Always adjust the coffee mill while in operation.
- Adjust one grinding level at a time and make at least 5 coffees before adjusting again.
- Do not remove the beans container while it contains beans.
4.3 The coffee filters
The appliance is provided with two coffee filters. The 1 coffee filter (C2) has the ☕ symbol marked on the bottom. The 2 coffee filter (C3) has the ☕ symbol marked on the bottom. For the correct quantity of coffee, the ideal level of pressed coffee is marked inside the filters. If the quantity is above or below the level indicated, the result may not be satisfactory. The next times you use the coffee mill, you can adjust the grinding level using the dial (B2) (see section "4.5 Adjusting the quantity of ground coffee in the filter").
4.4 Grind the coffee directly into the filter
- Place the ground coffee filter (C2) or (C3) in the filter holder (C1);
- Press the "X2" button if you are using the 2 coffee filter;
- Attach the filter holder to the outlet of the coffee mill (A22), aligning it with "INSERT", then turning it to the right. Grinding begins when the filter holder reaches the CLOSE position and stops automatically;
Important: while the appliance is grinding coffee, you can perform a rinse, or produce hot water or steam at the same time.
- Once grinding is complete, the ☕ light (B16) flashes. Pull the presser lever (A23) as far as it will go. The force exerted on the coffee is indicated on the lever itself. The light remains on steadily.
- Remove the filter holder by turning it towards the left.
Important: to adjust the correct quantity ground automatically into the filter holder, see section "4.5 Adjusting the quantity of ground coffee in the filter".
If you remove the filter holder from the outlet of the coffee mill without pressing the coffee, the ☕ light (B16) flashes. To press, turn the dial (B2) to the position to disable the coffee mill, re-attach the filter holder and pull the lever (A23).
4.5 Adjusting the quantity of ground coffee in the filter
Important: The first time you use the coffee mill, leave the dial in the position (min). It is normal for you to have to grind the coffee a number of times before finding the correct adjustment for the right amount of coffee.
5. COFFEE DELIVERY
5.1 Beverage selection
- Turn the mode selector dial (B8) to select the desired coffee (see section "5.4 Coffee beverages");
- If you use the 2 cup filter (C3), press the "2X" button (B3).
5.2 Delivering the coffee
- Attach the filter holder (C1) to the appliance. To attach correctly, align the filter holder handle with "INSERT", then turn the handle to the right until it is aligned in the "CLOSE" position;
- Place the cup or cups under the filter holder spouts;
- If you are using small cups, lower the cup grille (A10) to bring the filter holder spouts nearer the cup. This makes a better froth;
- Using the dial (B8), select the desired beverage.
Press the "OK" button. The appliance makes the coffee then stops automatically.
Please note: While the machine is making coffee, delivery can be interrupted at any moment by pressing the "OK" button. To remove the filter holder, turn the handle from right to left.
Danger of burns:
- To avoid splashes, never remove the filter holder while the appliance is delivering coffee. Wait for a few seconds after delivery.
- If no coffee is delivered, wait for about 1 minute before removing the filter holder. There could be a puff of steam caused by the residual pressure inside the appliance.
5.3 Pressure gauge
The pressure gauge enables you to check that pressure is correct while the coffee is being delivered. While making ESPRESSO coffee, the indicator will initially be in the "pre-infusion" sector and will then rotate to the "optimal zone" during delivery. For more information, see section "16. How to make perfect coffee".
Important: the pressure gauge only operates while coffee beverages are being made. If you are preparing hot water or using the steam function, the pressure gauge indicator does not move.
5.4 Coffee beverages
- ESPRESSO
Beverage of Italian origin, a short coffee with an intense aroma.
| Coffee | Pre-infusion | Quantity | Filter | x2 |
|---|---|---|---|---|
| Espresso | 1 cup 35 ml | C2 | ❌ | |
| Espresso | 2 cups 70 ml | C3 | ✔️ |
Always check that there is the right amount of coffee in the filter (see section "4.5 Adjusting the quantity of ground coffee in the filter").
- COFFEE
Beverage of European origin, a long coffee with a delicate aroma.
| Coffee | Pre-infusion | Quantity | Filter | x2 |
|---|---|---|---|---|
| Coffee | 1 cup 70 ml | C2 | ❌ | |
| Coffee | 2 cups 140 ml | C3 | ✔️ |
Always check that there is the right amount of coffee in the filter (see section "4.5 Adjusting the quantity of ground coffee in the filter").
- AMERICANO
Beverage of American origin, a long coffee. Made by delivering an espresso, followed by hot water added directly to the cup. Only one cup can be made at a time.
| Coffee | Pre-infusion | Quantity | Filter | x2 |
|---|---|---|---|---|
| Americano | 1 cup 120 ml | C2 | ❌ | |
| Americano | RECOMMENDED: | 1 cup 240 ml | C3 | ✔️ |
Always check that there is the right amount of coffee in the filter (see section "4.5 Adjusting the quantity of ground coffee in the filter").
6. CUSTOMISING THE QUANTITY OF COFFEE BEVERAGES WITH THE "MY" BUTTON (B7)
- Prepare the appliance to deliver 1 or 2 cups of the coffee beverage you want to make, as far as attaching the filter holder (C1) complete with the (C2) or (C3) filter and ground coffee.
- Turn the dial (B8) to select the coffee to be programmed.
- Press the "My" button: the light corresponding to the "OK" button (B5) comes on steadily and the light corresponding to the "My" button flashes.
- Press the "OK" button to start delivering the beverage. The lights corresponding to the "OK" and "My" buttons flash.
- When you have reached the desired quantity of the beverage, press the "OK" button again.
- Press the "My" button to save the new setting. The appliance is ready for use again and the "My" button remains on. If you do not want to save the new setting, press any other button.
Programming Americano coffee: follow the procedure described above for the quantities of both coffee and hot water.
Please note:
- You can programme coffee beverages, but not steam and hot water.
- Programming changes the quantity of the beverages, but not the amount of coffee ground.
- "X2" beverages can be programmed separately.
6.1 Beverage reset
To reset the default beverage quantities, press and hold the "My" button (B7) until it goes off. The selected beverage is reset to the default values.
7. USING PRE-GROUND COFFEE
- Place the ground coffee filter (C2) or (C3) in the filter holder (C1);
- Place the quantity of ground coffee in the filter;
- Turn the dial (B2) to the position to disable the coffee mill;
- Attach the filter holder to the outlet of the coffee mill (A22), aligning it with "INSERT", then turning it to the right;
- Pull the presser lever (A23) as far as it will go. The printing on the lever indicates the pressing force exerted;
- Remove the filter holder by turning it towards the left.
8. DELIVERING HOT WATER
- Choose the cup and place it on the correct cup grille (A10) or (A11).
- Press the ♨️ button (B6): the appliance delivers hot water from the spout (A5) then goes off automatically.
- To interrupt delivery, press the button again.
9. HOW TO MAKE MILK-BASED BEVERAGES
- Pour the quantity of milk you want to heat/froth into the milk jug (C9), remembering that the volume of milk doubles or triples in volume. For a denser more even froth, you should ideally use skimmed or partially skimmed cow's milk at refrigerator temperature (about 5°C).
- Choose the position of the ring (A7) according to the beverage to be prepared (see following table):
| Recommended position | Milk beverage to be prepared |
|---|---|
| FLAT | Hot milk (not frothed) / Caffelatte / Macchiato / Flat White |
| FOAM | Cappuccino, Espresso Macchiato, Hot Milk (frothed) |
- Place the jug (C9) containing the milk under the cappuccino maker (A8);
- Immerse the cappuccino maker in the milk jug. Never immerse the black ring;
- Turn the dial to the position. Steam to heat the milk is delivered from the cappuccino maker. If the ring is in the FOAM position, the steam gives the milk a creamy frothy appearance. To obtain a creamier froth, immerse the cappuccino maker in the milk and rotate the container with slow upward movements.
- When the required temperature (the ideal is 60°C) and froth density is reached, interrupt steam delivery by turning the dial to the position.
- For beverages requiring it, prepare the coffee (see section "4. Prepare the perfect dose"). Choose sufficiently large cups and place them on the espresso cup grille (A10). To use tall glasses, close the espresso cup grille (A10) and rest the glass on the cup grille for glasses or mugs (A11).
- Pour the frothed milk into the cups. Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.
Please note: Preparing cappuccino: consider about 100 g of milk for each cup.
10. CLEANING THE CAPPUCCINO MAKER AFTER USE
For hygiene reasons, the cappuccino maker should always be cleaned after use. Proceed as follows:
- Turn the steam dial to the position to deliver a little steam for a few seconds (points 2, 5 and 6 of the previous section). This causes the cappuccino maker to discharge any milk left inside.
- Press the ON/Standby button (B1) to turn the appliance off.
- Wait a few minutes for the cappuccino maker to cool down. With one hand, hold the cappuccino maker tube firmly, with the other, release the cappuccino maker by turning it anticlockwise, then pull off downwards;
- Remove the rubber steam connection nozzle from the spout by pulling it downwards;
- Push the ring upwards and make sure the two holes shown by the arrows are not blocked. If necessary, clean with a pin;
- Replace the connection nozzle, move the ring downwards and put the cappuccino maker back on the nozzle, turning it and pushing it upwards until it is attached.
For more thorough cleaning, use De'Longhi detergent.
11. ACTIVATING THE WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (C6). If this is not the case with your model, you are recommended to purchase one from De'Longhi Customer Services. To use the filter correctly, follow the instructions below.
- Remove the filter from the packaging;
- Turn the date indicator disk until the next 2 months of use are displayed;
Please note: The filter lasts about two months if the appliance is used normally. If the coffee machine is left unused with the filter installed, it will last a maximum of 3 weeks.
- To activate the filter, run tap water through the hole in the filter until water comes out of the openings at the side for more than a minute;
- Extract the tank (A17) (if necessary fill with water);
- Insert the filter in the water tank and immerse it completely for about ten seconds, sloping it and pressing it lightly to enable the air bubbles to escape;
- Place the filter in the filter housing (A18) and press as far as it will go. Close the tank, then put the tank back in the machine;
The filter is now active and you can use the coffee machine.
12. MENU SETTINGS
Please note: Once in the menu, you can modify all the menu functions as described in the previous sections.
12.1 Coffee temperature
To change the temperature of the water used to make the coffee, proceed as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons together for at least 3 seconds to access the menu. The ? (B15) and ☕ (B16) lights alternate;
- Turn the mode selection dial (B8) to the ESPRESSO position. The ♨️ light (B11) remains on steadily;
- Press the button corresponding to the desired selection as shown in the following table:
| Button | Temperature |
|---|---|
| X2 | Standard |
| OK | High |
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again).
12.2 Water hardness
The descale light (B9) comes on after a period of time established according to water hardness. The machine can also be programmed according to the actual hardness of the water supply in the various regions, in which case descaling may be required less frequently. Proceed as follows:
- Remove the "TOTAL HARDNESS TEST" indicator paper (C4) from its pack.
- Immerse the paper completely in a glass of water for one second.
- Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to one level.
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu. The ? (B15) and ☕ (B16) lights alternate;
- Turn the mode selection dial (B8) to the AMERICANO position. The descale light (B9) remains on steadily;
- Press the button corresponding to the desired selection as shown in the following table:
| Total Hardness Test result | Button | Level |
|---|---|---|
| X2 | 1 soft water | |
| OK | 2 medium water | |
| OK | 3 hard or very hard water |
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again).
12.3 Auto-off
Auto-off can be set so that the appliance goes off after 9 minutes, one and a half hours, or three hours. Proceed as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu. The ? (B15) and ☕ (B16) lights alternate;
- Turn the mode selector dial (B8) to the COFFEE position: The energy saving light (B13) remains on steadily;
- Press the button corresponding to the desired selection as shown in the following table:
| Button | Time |
|---|---|
| X2 | 9 minutes |
| OK | 1.5 hours |
| OK | 3 hours |
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again).
12.4 Default values
The appliance can be reset to the default values. Proceed as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu;
- Press and hold the "My" button for a few seconds until the corresponding light starts flashing;
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again).
12.5 Energy saving
Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance with European regulations. Proceed as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu;
- Press the ♨️ button (B6). The energy saving light (B12) comes on;
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again).
Please note:
- If energy saving is active, you may have to wait a few seconds before delivery.
- When energy saving is disabled, steam is delivered immediately.
12.6 Extra grinding adjustment
Over time, the burrs will wear down and the quantity of ground coffee will diminish. When adjusting the burrs as described in section "4.5 Adjusting the quantity of ground coffee in the filter" is no longer enough, you can select a new grinding range. Proceed as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu. The ? (B15) and ☕ (B16) lights alternate;
- Turn the mode selection dial (B8) to the position. The beans container empty light (B14) remains on steadily;
- Select the new grinding range by pressing the "Rinse" button (B4);
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again);
- Turn the ground coffee quantity dial (B2) to the "min" position, then proceed to adjust as though it were the first time ("4.5 Adjusting the quantity of ground coffee in the filter").
13. CLEANING
13.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:
- drip tray (A13) complete with cup grille (A11) and drip tray grille (A12);
- espresso cup grille (A10);
- coffee filters (C2) and (C3);
- the beans container (A2);
- the coffee mill burrs;
- the coffee mill outlet (A22) (smart tamping station);
- boiler outlet (A21);
- water tank (A17);
- cappuccino maker (A8) as described in section "10. Cleaning the cappuccino maker after use".
Important!
- Do not use solvents, abrasive detergents or alcohol to clean the coffee machine.
- Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces.
- None of the components of the appliance can be washed in a dishwasher with the exception of the drip tray (A13) and cup grilles (A10) and (A11).
- If the appliance is not used for more than a week, before using it again, we recommend you perform a rinse cycle as described in section "3. Setting up the appliance".
Danger!
- While cleaning, never immerse the coffee maker in water. It is an electrical appliance.
- Before cleaning the outside of the appliance, turn it off, unplug from the mains socket and allow to cool.
13.2 Cleaning the drip tray
The drip tray is fitted with a level indicator (A14) showing the amount of water it contains. Before the indicator protrudes from the cup tray, the drip tray must be emptied and cleaned, otherwise the water may overflow and damage the appliance, the surface it rests on or the surrounding area.
- Remove the drip tray (fig. 33).
- Remove the cup grille (A11), drip tray grille (A12) and level indicator (A14), empty the water and clean all the components with a cloth, then reassemble the drip tray.
- Put the drip tray back in place.
13.3 Cleaning the espresso cup grille
- Extract the grille (A10) by pulling it from the left, then removing it from the support;
- Clean the support with a cloth and wash the grille (dishwasher safe).
- Put the grille back on the support from the right side, then push until it is correctly attached;
13.4 Coffee filter cleaning and maintenance
The coffee filters are designed to obtain the best possible coffee froth. For best results, the filters must always be clean and free from all coffee residues.
After using the appliance, always rinse the filters under abundant running water, pushing the perforated filter to make sure it is always correctly inserted in its housing; make sure the hole underneath is free from all residues.
If still dirty, and in any case always at least once a month, clean the coffee filters thoroughly:
- Extract the perforated filter by pulling the tab;
- Rinse the filters under running water;
- Make sure the holes are not blocked. If necessary, clean with a pin;
- Dry all the components with a cloth.
- Put the perforated filter back in the housing and press as far as it will go.
13.5 Cleaning the boiler outlet
After every 200 coffees, rinse the boiler outlet. Press the rinse button (B4) and deliver about 200 ml of water.
13.6 Cleaning the water tank
- Remove the filter (*if present) and rinse with running water.
- Clean the water tank regularly (about once a month) and whenever you replace the water softener filter (C6) (*if present) with a damp cloth and a little mild washing up liquid, then rinse thoroughly.
- Replace the filter (*if present), fill the tank with fresh water and replace the tank.
- (Models with water softener filter only) Deliver about 100 ml of water.
Danger!
While cleaning, never immerse the coffee maker in water. It is an electrical appliance.
13.7 Cleaning the beans container
Without extracting it, clean the beans container regularly with a cloth. For more thorough cleaning, proceed as follows:
- Make sure the beans container (A2) is empty. If necessary, operate the coffee mill without beans to empty it:
- Release the beans container by turning it anticlockwise and extract from the appliance.
- Wash the container and lid (A1) with warm water. Do not wash the components in a dishwasher or use washing up liquid! Dry all accessories thoroughly before using again.
- Remove coffee residues;
- Clean the beans container housing with a damp cloth and dry;
- Put the container back as described in section "3. Setting up the appliance".
13.8 Cleaning the burrs
When cleaning the beans container, clean the container housing and upper burr with a damp cloth. The burr can be removed and replaced when worn. Contact an authorised customer services centre. You may also need to remove the burr if it becomes blocked with foreign matter. If this occurs, clean as follows:
- Empty the beans container (if necessary, using a vacuum cleaner to remove any remaining beans).
- Attach the filter holder and operate the mill without beans to free the coffee guide, then attach the filter holder to the outlet of the coffee mill (A22), lining it up with "INSERT", then turning it to the right. Grinding begins when the filter holder reaches the CLOSE position and stops automatically;
- Turn the appliance off;
- Remove the beans container as described in the previous section "13.7 Cleaning the beans container".
- Turn the fineness selector anticlockwise as far as it will go to the "REMOVE" position;
- Extract the upper burr, gripping it by the handle;
- Clean the burr with a brush and remove the coffee residues using a vacuum cleaner;
- Put the upper burr back in place: Insert the burr in its housing; Turn the selector to select the desired grinding level; Make sure the burr is inserted correctly by pulling it by the handle. If it is correctly inserted, it will not move;
- Use a brush to remove any coffee residues from the outlet of the coffee mill (A22).
13.9 Replacing the burrs
When the quantity of coffee becomes even less, contact a customer services centre to have the burrs replaced, then adjust the mill again as follows:
- Press and hold the "X2" (B3) and "My" (B7) buttons for at least 3 seconds to access the menu. The ? (B15) and ☕ (B16) lights alternate;
- Turn the mode selection dial (B8) to the position. The beans container empty light (B14) remains on steadily;
- Select the original grinding range by pressing the "X2" button;
- Press the ON/Standby button (B1) to exit the menu. (If the appliance is left idle for about 1 minute, it exits automatically from the settings menu and is ready for use again);
- Turn the ground coffee quantity dial (B2) to the "min" position, then proceed to adjust as though it were the first time ("4.5 Adjusting the quantity of ground coffee in the filter").
13.10 Cleaning the "Smart tamping station"
To guarantee top quality grinding, clean the "Smart tamping station" regularly as follows:
- Clean the attachment area with a brush;
- Pull the lever (A23) as far as it will go and clean the presser cylinder with a brush. Then release the lever.
- Use the tube brush (C8) to clean the coffee guide;
13.11 Other cleaning operations
- Do not use solvents or abrasive detergents to clean the coffee maker. Use a soft damp cloth only.
- Clean the filter holder cup.
- You are recommended to use De'Longhi detergent.
14. DESCALING
Descale the appliance when the descale light (B9) comes on.
- Before use, read the instructions and the labelling on the descaler pack.
- It is important to use De'Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer's guarantee.
Proceed as follows:
- (IF PRESENT, REMOVE THE WATER SOFTENER FILTER). Pour the descaler into the tank up to the level A marked inside the tank (equal to one 100ml packet), then add water (1 litre) up to the level B.
- If the appliance is off, press the ON/Standby button (B1).
- Make sure the filter holder is not attached and position a recipient under the spouts (A5), (A6) and the boiler outlet (A21);
- Turn the mode selector dial (B8) to the position. The light flashes and the "OK" light comes on.
- Press "OK" (B5) to start descaling.
- The descale programme starts and the descaler liquid comes out of the spouts and boiler outlet. The descale programme removes limescale deposits from inside the appliance by automatically performing a series of rinses and pauses until the tank is empty.
- Delivery stops and the ? (B15) and rinse button (B4) lights corresponding to the rinse button (B4) come on.
- Empty the recipient used to collect the descaler solution and replace it empty under the spouts.
- Remove the water tank, empty any residues of descaler solution, rinse with running water and fill with fresh water up to the MAX level. Put the tank back in its housing.
- Press the ? button. The appliance rinses the internal circuits and delivers water from all three spouts.
- When rinsing is complete, delivery stops. All the LEDs flash briefly and the appliance prepares to be used again.
- Empty the recipient used to collect the rinse water.
- Extract and empty the drip tray, then put back in the appliance.
- Extract the tank, fill with fresh water, then put back in the appliance.
- Turn the mode selector dial to one of the coffee positions.
15. TECHNICAL DATA
| Mains voltage: | 220-240V~50-60Hz |
|---|---|
| Absorbed power: | 1450W |
| Size LxDxH: | 375x368x445 mm |
| MAX. pressure: | 19 bars |
| Water tank capacity: | 2 L |
| Power cable length: | 1200 mm |
| Weight: | 12 kg |
16. HOW TO MAKE PERFECT COFFEE
| PERFECT ESPRESSO | UNDER-EXTRACTED COFFEE | OVER-EXTRACTED COFFEE |
|---|---|---|
| FROTH: nut-brown coloured with dark lights and light-coloured streaks, 3-4 mm thick | FROTH: clear and thin with large bubbles | FROTH: dark and thin, only at the edges |
| BODY: dense, full-flavoured and smooth | BODY: thin, watery | BODY: excessive |
| TASTE: well-balanced and lingering | TASTE: weak and short-lived | TASTE: strong, astringent, lingering and bitter on the palate |
| AROMA: intense | AROMA: not pronounced | AROMA: weak, with a hint of burnt coffee |
| GRINDING LEVEL: Correct | GRINDING LEVEL: too coarse. Adjust the mill to a lower position, following the instructions in section "4.5 Adjusting the quantity of ground coffee in the filter" | GRINDING LEVEL: too fine. Adjust the mill to a higher position, following the instructions in section "4.5 Adjusting the quantity of ground coffee in the filter" |
| COFFEE QUANTITY: Correct | QUANTITY OF COFFEE IN FILTER: Not enough. Increase the quantity by turning the dial "B2. Ground coffee quantity dial" as described in section "4.5 Adjusting the quantity of ground coffee in the filter" | QUANTITY OF COFFEE IN FILTER: Too much: reduce the quantity by turning the dial "B2. Ground coffee quantity dial" as described in section "4.5 Adjusting the quantity of ground coffee in the filter" |
17. EXPLANATION OF LIGHTS
| LIGHTS | EXPLANATION OF LIGHTS | OPERATION |
|---|---|---|
| All the lights flash briefly | Turning the machine on | Self-diagnosis |
| ? on | Insufficient water in tank or water tank not inserted correctly | Fill the tank or extract the tank and put it back correctly |
| ? on | Energy saving is enabled | See section "12.5 Energy saving" if you want to disable the function |
| ♨️ on | The appliance is on and ready for use | The appliance is at the right temperature to deliver steam. To deliver steam, turn the steam dial (A4) |
| ♨️ flashing | The appliance is on and energy saving is enabled. The steam dial (A4) is in the steam delivery position | The light flashes to indicate that the appliance is preparing to deliver steam. Delivery begins as soon as the appliance is at temperature |
| ♨️ flashing | The appliance is heating up to be ready for use | The appliance is at temperature when the light remains on steadily |
| ♨️ on | Steam delivery has ended and the steam dial (A4) is in the steam position | Turn the dial to the position. |
| ☕ flashing | The filter holder has been detached from the coffee mill without pressing | Detach the filter holder and press the coffee as described in section "7. Using pre-ground coffee" |
| ☕ on | Pressing is needed | The coffee has just been ground and the filter holder is attached to the coffee mill |
| ☕ on | Pressing has been performed correctly | |
| ☕ on | The beans container is empty | Fill the beans container |
| ☕ flashing | The beans container is not inserted or is not correctly screwed in place, or the selector on the bottom of the container is not in a position from 1 to 6. | Put the beans container in the appliance correctly |
| ♨️ flashing | The appliance is too hot to make coffee | Wait for it to cool |
| ♨️ flashing | Descaling is underway | Complete the operation as described in section "14. Descaling" |
| ♨️ flashing | Descaling has ended and the dial (B8) is in the "descaling" position | Turn the mode selector dial to one of the "coffee positions" |
18. ALARMS
| LIGHTS | ALARM | SOLUTION |
|---|---|---|
| ! on | General alarm | Contact Customer Services |
| + flashing | The drip tray (A13) is missing or has not been inserted correctly | Extract the drip tray then put back correctly in the appliance |
| ♨️ on | Descaling must be performed | Descale the appliance as described in section "14. Descaling" |
| ♨️ flashing quickly | The dial (B8) is in the descaling position | Turn the dial to one of the beverage positions |
| + flashing | The filter holder has been detached before grinding has ended or pressing has been performed too quickly | Repeat grinding |
| + flashing | The coffee mill coffee guide is clogged | Clean as described in section "13.10 Cleaning the "Smart tamping station"" and section "19. Troubleshooting" in correspondence to fig. 50. |
| + flashing | The burrs are blocked by foreign matter | Remove the foreign matter and clean the burrs as described in section "13.8 Cleaning the burrs". |
| ☕ + ♨️ flashing | The appliance is being turned on for the first time and the water circuit must be filled. | Proceed as described in section "3. Setting up the appliance" |
| ♨️ + ? flashing | If the water softener filter (C6) is present, an air bubble may have been released inside the circuit, obstructing delivery | Press the ♨️ button (B6) corresponding to the light. Delivery begins and stops automatically. |
| ☕ + ♨️ flashing | The grinding is too fine and the coffee is delivered too slowly or not at all | Extract the filter holder and repeat the operations to make the coffee, bearing in mind the indications in section "4.5 Adjusting the quantity of ground coffee in the filter" and table "16. How to make perfect coffee". |
19. TROUBLESHOOTING
| PROBLEM | CAUSE | SOLUTION |
|---|---|---|
| No espresso coffee is delivered | No water in the tank (A17) | Fill the tank |
| The ♨️ light is on and the ? light is flashing to indicate that the coffee or steam circuit is empty. | Press the button corresponding to the ♨️ light to fill the circuit. | |
| The filter is blocked, or the perforated filter is missing | Clean as described in section "13.4 Coffee filter cleaning and maintenance" and make sure the perforated filter is put back correctly | |
| The tank has been inserted incorrectly and the valves on the bottom are not open | Press the tank down lightly to open the valves on the bottom | |
| Scale in the water circuit | Descale as described in section "14. Descaling" | |
| The dial (B2) has been turned to the maximum adjustment possible | When not enough coffee is ground to reach the correct quantity, select the new grinding range as described in section "12.6 Extra grinding adjustment". | |
| The filter holder cannot be attached to the appliance | The ground coffee has not been pressed or is too much | Clean as described in section "4.4 Grind the coffee directly into the filter" |
| The espresso coffee drips from the edges of the filter holder rather than the holes | The filter holder is inserted incorrectly | Attach the filter holder correctly and rotate firmly as far as it will go |
| The espresso boiler gasket has lost elasticity or is dirty | Have the espresso boiler gasket replaced by Customer Services | |
| The filter is clogged, or the perforated filter is missing or dirty | Clean as described in section "13.4 Coffee filter cleaning and maintenance" | |
| The coffee froth is too light (delivered from the spout too fast) | The appliance settings need reviewing | See section "16. How to make perfect coffee" |
| The coffee froth is too dark (delivered from the spout too slowly) | The appliance settings need reviewing | See section "16. How to make perfect coffee" |
| No milk froth is formed when making cappuccino | The ring (A7) is in the "FLAT" (NO FROTH) position | Push the ring into the "FOAM" position |
| Milk not cold enough | Always use semi-skimmed milk at refrigerator temperature. | |
| The cappuccino maker (A8) is dirty | Clean the cappuccino maker as described in section "10. Cleaning the cappuccino maker after use" | |
| Scale in the water circuit | Descale as described in section "14. Descaling" | |
| At the end of descaling, the appliance requests a further rinse | During the rinse cycle, the water tank has not been filled to the MAX level | Repeat the rinse cycle from point (8) of section "14. Descaling" |
| The appliance does not grind the coffee | There is foreign matter that cannot be ground in the coffee mill | Clean the burrs as described in section "13.8 Cleaning the burrs", making sure you remove all the beans from the beans container (A2) before extracting it. Before putting the burr back, vacuum all residues from the housing (fig. 44). |
| If you want to change the type of coffee | You must remove all the beans present in the machine | Empty the beans container (if necessary, operate the coffee mill without beans or use a vacuum cleaner to remove any remaining beans). Attach the filter holder and operate the coffee mill a number of times without beans to free the coffee guide. Attach the filter holder to the outlet of the mill (A22), lining it up with "INSERT", then turning it to the right. Grinding begins when the filter holder reaches the CLOSE position and stops automatically. Repeat until the filter is empty. Place the new coffee in the beans container. If the amount of coffee ground is not enough to reach the "perfect quantity", proceed as described in section "4.5 Adjusting the quantity of ground coffee in the filter". |
| After grinding, the coffee filter is empty | The coffee mill coffee guide is clogged | Clean as described in section "13.10 Cleaning the "Smart tamping station"". If the problem persists, access the guide by opening the hatch and free it using the brush (fig. 50). |
| After grinding, there is too much coffee in the filter | The "Smart Tamping Station" needs cleaning | Clean as described in section "13.11 Cleaning the "tamping station", then grind again. |
| After grinding, the ground coffee in the filter does not reach the "perfect amount of coffee" | The quantity of ground coffee needs adjusting | Adjust the quantity of coffee with the dial (B2), following the instructions in section "4.5 Adjusting the quantity of ground coffee in the filter". If the dial is already in the max. position, proceed as described in section "12.6 Extra grinding adjustment". |
| Over time the burrs wear down | Replace the burrs as described in section "13.9 Replacing the burrs". |
