Mad Dog GM805 Gaming Mouse: Operating Manual and Warranty Terms
An official guide for the Mad Dog GM805 gaming mouse, covering setup, features, safety, troubleshooting, and warranty information.
Introduction
Thank you for choosing the Mad Dog GM805 gaming mouse. We are confident that this high-quality device will provide you with enjoyment and satisfaction. Please read and follow this operating manual carefully. The device is intended for domestic or other non-commercial use. The manufacturer is not liable for damages resulting from improper or non-compliant use.
Safety and Hazard Conditions
- Use the product only as intended.
- Do not tamper with the interior of the device, attempt to repair, or modify it yourself.
- The device is not a toy; keep it away from children.
- Do not use the device near sources of heat.
- Do not immerse the device in water or other liquids.
- Protect the device from excessive sunlight and moisture. Do not use in rooms with increased dustiness or air pollution.
- Do not wrap the power cord around the device.
- Do not store the device in places exposed to sudden changes in ambient temperature. After a possible change of environment, wait about 30 minutes before connecting the device to the computer.
- The device is not a toy. Keep it away from children. The cable may twist around the neck and cause suffocation.
- Charging should be carried out in a dry, well-ventilated place not exposed to direct sunlight.
- Do not expose the device to excessively high or low temperatures: below 0°C or above 40°C.
- Do not leave unattended while charging.
- Do not attempt to replace the battery yourself.
- Do not look directly into the light of the mouse LED, as it is harmful to the eyes and may result in visual impairment.
- Do not direct the light towards people and animals.
- Any repairs should be performed by the manufacturer, an authorized service center, or a person with appropriate qualifications.
- Do not consume food or drink directly above the device.
Device Description
The Mad Dog GM805 gaming mouse features:
- 1. Left Mouse Button
- 2. Right Mouse Button
- 3. Scroll / Middle Mouse Button
- 4. Front Side Button
- 5. Rear Side Button
- 6. DPI Change Button
- 7. Interchangeable Cover: The mouse comes with two interchangeable covers.
- 8. USB-C Port: For wired connection and charging.
- 9. Backlight Change Button
- 10. Sensor: Located on the bottom of the mouse.
- 11. Operating Mode Switch: Located on the bottom of the mouse.
- 12. Sliders: Located on the bottom of the mouse for smooth movement.
- 13. RF Receiver: For wireless connection.
- 14. USB Cable: For wired connection and charging.
- 15. USB-C Adapter: For connecting to USB-C ports.
Diagram shows a top view of the mouse with numbered buttons and ports, a bottom view showing the sensor and sliders, and separate views of the RF receiver and USB-C adapter.
Technical Data
| Model | GM805 |
|---|---|
| Intended Use | For Right-Handed Persons |
| Sensor | Pixart PAW3335 |
| LMB and RMB Switches | Huano 20 million clicks |
| Number of Buttons | 7 |
| Maximum Resolution | up to 16000 DPI |
| Number of DPI Modes | 6 |
| Reporting Frequency | up to 1000 Hz |
| Maximum Acceleration | up to 40 G |
| Peak Speed | ~10 m/s |
| Backlight | LED RGB |
| Number of Backlight Modes | 10 |
| Weight (without cable) | ca. 80g |
| Cable Type | Braided with ferrite ring |
| Cable Length | 1.8 m |
| Transmission Frequency | 2402 MHz – 2480 MHz |
| Maximum Transmission Power | up to 5 dBm |
| Operating Time | up to 40 hours* (*Battery life depends on backlight mode) |
| Charging Time | up to 3 hours |
| Power Supply | 5.0 V ⎓ 0.5 A |
| Battery | Li-ion DC 3.7 V, 430 mAh |
| Power Supply with Wired Connection | From USB 5.0 V ⎓ 0.2 A |
| OS Compatibility | Windows XP/7/8/10/11 |
Operation of the Device
First Connection
- Connect the mouse to a computer's USB port using the included cable. The device will automatically install the necessary driver.
- Once the operating system confirms driver installation, the device is ready for use.
The mouse can be used in two modes:
- Wireless: Connect the RF receiver to a computer USB port.
- Wired: Connect the mouse to the computer using the included USB cable.
DPI Change
The mouse has 6 DPI settings. Switch between them using the designated button (button 6, located in front of the scroll wheel). The scroll wheel's LED backlight will change color to indicate the selected DPI:
- Red: 800 DPI
- Green: 1600 DPI
- Blue: 3200 DPI
- Violet: 6400 DPI
- Yellow: 12000 DPI
- Cyan: 16000 DPI
Each DPI profile can be customized using software downloadable from the manufacturer's website.
Selecting the Operating Mode
The switch on the bottom of the mouse allows selection of one of three operating modes:
- OFF: Mouse is turned off.
- LED: Mouse is on with backlight enabled.
- ON: Mouse is on without backlight.
Diagram shows a three-position switch labeled OFF, LED, and ON.
RGB Backlight
The mouse features 10 different RGB LED backlight modes. To cycle through the modes, press button 6 (in front of the scroll wheel).
Rear Cover Replacement
Two interchangeable covers are included. To remove the current cover, gently pry it from the rear of the device at the indicated spot. To install a new cover, align it and place it; it will connect magnetically.
Diagram shows an arrow pointing to the rear of the mouse where the cover can be pried off.
Software
Software Installation
- Visit http://maddog.pl/sterowniki/sterowniki-i-instrukcje.
- Select the device type and model.
- Download the software installation file.
- Install the software on your computer.
Software Support
The software manual is available for download at: http://maddog.pl/sterowniki/sterowniki-i-instrukcje.
Charging
When the mouse scroll wheel starts flashing red, it indicates a low battery level and the need for charging.
To recharge the mouse, connect it to a computer's USB port using the provided cable. The mouse will enter wired mode, allowing simultaneous charging and use. During charging, the scroll wheel will blink blue. Once fully charged, the scroll wheel's color will become solid, reflecting the DPI setting for wired mode.
Battery Care and Longevity
CAUTION! Battery deterioration during operation is a natural phenomenon. To keep the battery in good condition and extend its life, please follow these guidelines:
- Do not operate the device if the battery is discharged.
- Charge the battery according to the voltage and charging current data on the rating plate.
- Before extended storage, charge the battery to 50% and recharge it every 3-4 months. If the product does not allow checking the charge level, discharge the device, then charge it for half the time required for a full charge. Leaving a discharged battery for a prolonged period may result in damage or loss of properties.
- When using the device regularly, avoid full battery discharge and always charge it to full.
- Once the battery is charged, disconnect the charger plug from the device.
- Do not leave the device unattended while charging.
- Using chargers and cables other than those recommended in the manual may lead to product damage or battery explosion.
- Charge in a dry, well-ventilated place not exposed to direct sunlight.
Cleaning and Maintenance
Clean the device with a lightly dampened soft cloth. The interior can be cleaned with compressed air, used at a distance of more than 5 cm.
When not in use, store the device in its original packaging to protect it from dust and moisture. During transport, place the RF receiver in its dedicated location, accessible after removing the rear cover.
PLEASE NOTE: DO NOT IMMERSE THE DEVICE IN WATER. DO NOT USE WATER OR CHEMICALS FOR CLEANING.
Problems and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| The device does not start. | Incorrectly connected plug to the computer connector. | Connect the plug to the computer connector correctly. |
| The device does not start. | The computer has not installed the device driver. | Connect the cable plug to the USB connector on the computer and wait for the device driver to be installed. |
| The mouse cursor moves very fast or very slowly. | Too high or too low DPI resolution set. | Change the DPI resolution by pressing the DPI change button. |
| The mouse cursor freezes or does not move. | The optical hole at the bottom of the mouse is dirty. | Clean the underside of the mouse. |
| The mouse cursor freezes or does not move. | The texture of the surface on which the mouse works negatively affects the sensor operation. | It is recommended to use a mouse pad. |
| The mouse cursor freezes or does not move. | After a long time without activity, the mouse will go to standby. | Press any mouse button to wake up the device. |
| Unable to connect mouse to computer. | No USB-A port in the computer. | Connect the mouse to the computer via the USB-C adapter included in the set. |
| The device is not charging. | Wrong charging cable. | Use the USB-C/A cable included in the set for charging. |
Declaration
ART-DOM Sp. z o.o. hereby declares that the GM805 wireless mouse complies with the relevant requirements of the Union harmonisation legislation: Directive 2014/53/EU and other Union harmonisation legislation. The full text of the EU declaration of conformity is available at the following address: www.artdom.net.pl/deklaracja/GM805/.
Eco-Friendly and Environmentally Friendly Disposal
This device is marked, in accordance with Directive 2012/19/EU of the European Parliament and of the Council of 4 July 2012 on waste electrical and electronic equipment (WEEE), with the symbol of a crossed-out waste container:
Symbol of a crossed-out waste container.
Do not dispose of the device marked with this symbol together with household waste. For disposal, return the device to your local waste treatment and disposal facility or contact your local authorities.
YOU CAN HELP PROTECT THE ENVIRONMENT! Proper handling of waste electrical and electronic equipment contributes to avoiding harmful consequences for human health and the environment resulting from the presence of hazardous components and improper storage and processing of such equipment.
Warranty Conditions for the Mouse
- ART-DOM Sp. z o.o., with its registered office in Łódź (92-402) at ul. Zakładowa 90/92, National Court Register Number 0000354059 (Guarantor), guarantees that the purchased device is free from physical defects. The warranty covers only defects resulting from causes inherent in the item sold (manufacturing defects).
- A disclosed defect will be removed at the Guarantor's expense within 14 days from the date of reporting the damage to the authorized service or point of sale.
- In exceptional cases, e.g., the need to import spare parts from their manufacturer, the repair period may be extended up to 30 days.
- The warranty period for the user is 24 months from the date of delivery of the goods.
- The goods are intended for use only in the conditions of an individual household.
- The present warranty does not cover:
- damage caused by using the device in a manner inconsistent with the user manual,
- mechanical, chemical, or thermal damage,
- repairs and modifications made by companies or persons not authorized by the manufacturer,
- parts that are easily used or consumables such as: batteries, bulbs, fuses, filters, knobs, shelves, accessories,
- installation, maintenance, inspection, cleaning, unlocking, removal of contaminants, and instruction.
- The Guarantor will select the mode of defect removal at its own discretion. Removal of a confirmed defect will take place through warranty repair or replacement. The Guarantor may perform repairs when the buyer requests replacement, or replacements when the buyer requests repair, if bringing the device into conformity in the manner selected by the buyer is impossible or would require excessive costs for the Guarantor. In particularly justified cases, if both repair and replacement are impossible or would require excessive costs, the Guarantor may refuse to bring the goods into compliance and propose another way to settle the warranty claim.
- Exchange of goods is made at the point of sale where purchased (replacement or refund) or an authorized service point (for replacement). The returned device must be complete, without mechanical damage. Failure to comply may result in the warranty claim being rejected.
- In case of non-compliance of goods with the sales contract, the buyer is entitled by law to legal protection measures at the seller's expense; the warranty does not affect these measures.
- The warranty is valid in Poland.
- The condition for warranty repair or replacement is the presentation of proof of purchase and use of the goods in accordance with the user manual.
CAUTION! Damage or removal of the rating plate from the device may result in the warranty being deemed void.
We are constantly improving our products, so they may differ slightly from the images presented on the packaging and in the user manual. Please read the user manual before operating the appliance.
ART-DOM Sp. z o.o., ul. Zakładowa 90/92, 92-402 Łódź. National Court Register number 0000354059.
