Kingfisher Ceiling Fan Installation and User Manual

Important Safety Information

⚠️ WARNING: This document is a combined manual. Please ensure the instruction manual and safety manual are split out and printed separately, including blank pages. DO NOT PRINT THIS PAGE.

These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.

General Safety & Installation Requirements:

• All installations must be performed by a competent person in accordance with local regulations (e.g., IET wiring regulation BS7671).
• Installation method: Please refer to the Installation section.
• Means of disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The ceiling fan must be fitted in rooms where the blades are more than 2.3 metres (7' 6 1/2") from the floor. Please allow 500 mm (19 3/4") distance between the tips of the blades and the walls or furnishings.
• Check the pack and make sure you have all of the parts listed.
• Remove all packaging, wrap etc. from the product.
• Decide on the appropriate location for your product.
• This product is suitable for indoor use only and not for areas constantly subject to moisture such as bathrooms.
• Always refer to the installation drawing for the orientation of the product.
• Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
• IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the ceiling fan.
• The fixing means for attachment to the ceiling (e.g., hooks) shall be fixed with sufficient strength to withstand 4 times the weight of the ceiling fan.
• The mounting of the suspension system and the replacement of parts of the safety suspension system device shall be performed by suitably qualified persons.
• Wiring diagrams are for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.
• Never put anything on the product or hang anything on any part of this product.
• Never use the terminal cables to bear the product weight.
• WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact suitably qualified persons.
• If you have any doubt about installation/use of this product, consult a qualified electrician.
• Always disconnect the product from mains at least 10 minutes, allowing it to cool down before any maintenance or adjustment.

Product Specifications

Installation Guide

Refer to the following steps and diagrams for installation. Ensure all parts are present before starting.

Parts List:

• ? Mounting Bracket [01] x 1
• ? Ceiling Canopy [02] x 1
• ? Blade Holder [03] x 4
• ? Fan Blade [04] x 4
• ? Light Shade/Cover [05] x 1
• ? Screw [A] (Ø5 mm) x 2 (for bracket)
• ? Screw [B] (Ø5 x 50 mm) x 2 (for mounting bracket to ceiling)
• ? Screw [C] (Ø5 mm) x 2 (for canopy)
• ? Screw [D] (Ø5 mm) x 13 (for blade holders)
• ? Screw [E] (M5 mm) x 1 (for wiring terminal block cover)
• ? Screw [F] (M5 mm) x 13 (for attaching blades to holders)
• ? Screw [G] (Ø5 mm) x 13 (for attaching holders to motor)
• ? Screw [H] (M5 x 15 mm) x 13 (for attaching blades to holders)
• ? Screw [I] (11.3 x 18.3 mm) x 3 (for light shade)

Step 01: Electrical Disconnection

Ensure the main power supply is switched OFF at the circuit breaker or fuse box. The switch should be in the 'OFF' position. ?

Step 02: Mount the Bracket

Attach the mounting bracket [01] to the ceiling using appropriate screws [B] for your ceiling type (concrete or wooden). Ensure the bracket is securely fastened and can support the fan's weight. ⚠️ Check for pipes and cables before drilling.

Step 03: Prepare Ceiling Mount

For concrete ceilings (A), drill holes and insert appropriate anchors. For wooden ceilings (B), screw directly into the joists. Ensure the mounting points can support the fan's weight.

Step 04: Attach Mounting Plate

Attach the fan's mounting plate to the ceiling bracket. Ensure it is securely locked.

Step 05: Wiring

Connect the fan's wires to the house wiring. Typically: Live (L) to Brown/Red, Neutral (N) to Blue/Black, and Earth to Green/Yellow. Refer to the terminal markings on the fan and your house wiring. Ensure all connections are tight. ?

Wire colours may vary by region. Refer to the multilingual guide for specific colour codes.

Step 06: Attach Canopy

Slide the ceiling canopy [02] up to cover the mounting bracket and wiring. Secure it in place.

Step 07: Secure Canopy

Ensure the canopy is firmly attached.

Step 08: Attach Blade Holders

Attach the blade holders [03] to the fan blades [04] using screws [F] or [H] as appropriate.

Step 09: Attach Blades to Motor

Secure the assembled blades and holders to the fan motor using screws [G].

Step 10: Attach Blades to Motor (Alternative Method)

Follow the diagram to attach the blades to the motor assembly.

Step 11: Install Light Bulb

Screw in a compatible light bulb (Max 60W E27) into the socket. ?

Step 12: Attach Light Shade

Carefully attach the light shade/cover [05] to the fan assembly using the provided screws [I].

Operation and Blade Adjustment

Blade Adjustment (Forward/Reverse Airflow)

The fan can be set to rotate clockwise or counter-clockwise to provide different airflow patterns:

• Summer Mode (Downward Airflow): Typically achieved by setting the fan to rotate counter-clockwise. This creates a cooling downdraft. ☀️
• Winter Mode (Upward Airflow): Typically achieved by setting the fan to rotate clockwise. This circulates warm air trapped near the ceiling downwards without creating a direct draft. ❄️

Refer to the diagrams for specific switch settings or blade direction adjustments.

Fan Speed Control:

Use the pull chains or remote control (if applicable) to cycle through fan speeds (e.g., OFF, Speed 1, Speed 2, Speed 3, ON). The specific method depends on your model.

Light Control:

Use the pull chain or switch to turn the light ON/OFF.

Care and Maintenance

• Always disconnect the fan from the power supply before cleaning or maintenance.
• Clean the fan blades and motor housing with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Ensure all screws and connections remain tight.
• Periodically check the fan for any unusual noises or vibrations. If observed, stop use and consult a qualified electrician.

Warranty Information

This product is covered by a 2-year warranty against manufacturing defects from the date of purchase, for normal, non-professional household use. The warranty is valid upon presentation of the till receipt or invoice. It covers product breakdowns and malfunctions under the condition that the product is used in accordance with its intended use and subject to proper installation and maintenance. The warranty does not cover defects caused by normal wear and tear, misuse, accident, or improper maintenance. For full details, please refer to the warranty section in the original manual.

Manufacturer and Distributor Information

Manufacturer: Kingfisher International Products Limited / Kingfisher International Products B.V.

Distributors include:

• UK/EU: Kingfisher
• France: Castorama, Bricodepot
• Poland: Castorama
• Russia: ООО «Касторама РУС»
• Romania: Bricodepot
• Spain: Bricodepot
• Portugal: Bricodepot
• Turkey: KOÇTAŞ YAPI MARKETLERİ TİC. A.Ş.

For online manuals, visit: www.kingfisher.com/products