Xiaomi Mi Smart Standing Fan 1X User Manual
Safety Instructions
Read this manual carefully before use, and retain it for future reference.
PRECAUTIONS
Handling the Fan
- Turn off and unplug the fan before moving it.
- Firmly hold the fan stand to avoid it from falling down and causing personal injury.
Installation
- Make sure the fan is properly installed according to the instructions, so as to avoid electric shocks, fire, personal injury, or other damage.
- Do not connect the fan to a power outlet as long as it is not assembled.
- Once assembly completed, it's strictly forbidden to remove the guards for any purpose.
Using the Fan
- Immediately stop using the fan if it makes unusual sounds, gives off bad odors, overheats, or rotates irregularly.
- Do not lean on or tilt the fan while it is running.
- Do not push the fan's head repeatedly so as to avoid damage to the internal mechanism.
Power Cord
- Unplug the power cord from the power outlet before performing any maintenance or moving the fan.
- Do not pull the cord, always unplug the fan by holding and pulling the power plug.
- The appliance is only to be used with the power supply unit provided with the appliance.
- When the power cord is damaged, it must be replaced with a genuine power cord purchased from the manufacturer or after-sales service department.
WARNINGS
Improper use may lead to electric shocks, fire, personal injury, or other damage.
- Do not use this fan in place where it is easy to fall over or where there are other unstable objects nearby.
- Do not use this fan in hot and humid environments such as a bathroom.
- Do not use this fan if its power cord is damaged or its power plug is loose.
- Do not use this fan if its front grille is not installed, or its rear grille is loose or fell off.
- Do not disassemble or repair this fan.
- Do not pinch, bend, or twist the power cord too much, so as to prevent from exposing or breaking its core.
- Do not insert your fingers or any object into the front grille, rear grille, or the fan blades when the fan is in use.
- Keep hair and fabrics away from the fan to avoid getting them caught in the fan.
- Do not use any improper power outlet.
- Do not use the supplied power cord with any other device.
- Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Ensure that the fan is switched off from the supply mains before removing the guard.
- If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
Package Contents
- 1: Base
- 2: Fan Assembly (front grille, fan blade assembly, rear grille)
- 3: Fan Blade Assembly Knob
- 4: Allen Key
- 5: Fan Grille Knob
- 6: Base Bolt
- 7: Fan Grille Screw
- 8: Power Cord
- 9: User Manual
- 10: Motor & Stand
Overview
Top View:
- Natural Breeze Indicator
- Wi-Fi Indicator
- Speed/Schedule Indicator
- On/Off Button
- Speed Adjustment/Mode Switch Button
- Oscillation Button
- Scheduled Turn-off Button
- Center Point Indicator (no light effect): Center point for the fan's head angle range
Stand:
- Base
- Base Bolt
- Power Port
Installation Instructions
Step 1: Base installation
- Install motor & stand onto base as shown in the figure above.
- Insert base bolt into the hole on the bottom of the base.
- Use Allen key to turn base bolt clockwise to fix the stand to the base.
Step 2: Open the fan assembly
Take fan assembly apart, then turn the front grille counter-clockwise until it separates from the rear grille, as shown in Figure 1. Remove the fan blade assembly as indicated by Figure 2.
- Figure 1: Front grille, fan blade assembly, rear grille
- Figure 2: Fan Assembly
Step 3: Install the rear grille
Firstly, install the rear grille to the motor's shaft with " facing upwards, and then install fan grille knob onto the shaft. Turn the knob clockwise to firmly fix the rear grille to the motor's shaft.
Step 4: Install the fan blade assembly
Align the center hole of the fan blade assembly with the motor's shaft and install it onto the shaft, then install fan blade assembly knob onto the motor's shaft. Turn the knob counter-clockwise in order to fix the fan blade assembly to the motor's shaft.
Step 5: Install the front grille
- Align Front Grille Alignment Mark with Rear Grille Left Alignment Mark, and make sure the front grille is properly embedded into the rear grille.
- Turn the front grille clockwise until the Front Grille Alignment Mark aligns the Rear Grille Right Alignment Mark. Make sure the grilles are securely fastened.
Step 6: Fasten the front grille
Insert fan grille screw into the hole at the bottom of the fan grille. Turn the screw clockwise by using the Allen key to tighten it.
How to Use
Connect to a power outlet
Connect the power cable to the power port on the base and then plug it into a power outlet. When you hear a beep, the fan is successfully connected to the power supply.
Turn on/off
- Turn on: Press the button to start the fan. When turned on for the first time, the default speed is slow (1). After turning off the fan and turning it back on again, the speed will be the last used one.
- Turn off: When the fan is working, press and hold the button to stop it.
Adjust speed & switch mode
Adjust speed
Press the button to adjust the speed. With each press, the speed will go up one level and the corresponding status indicator(s) will be on. After turbo (4), the speed will return to slow (1).
- Fan Speed Indicator Status: Slow (1) ••••, Medium (2) ••••, Fast (3) ••••, Turbo (4) ••••
Switching mode
Press and hold the button to switch between direct and natural breeze. The indicator is on while in natural breeze mode and is off while in direct breeze mode. The speed will not be changed when switching modes.
- Note: The factory default is direct breeze mode. After turning off the fan and turning it back on again, the mode will be the last used one.
Control oscillation
Press the button to enable or disable 140° oscillation. After turning off the fan and turning it back on again, the oscillation setting will be the last used one. Unplug then plug the fan in or reset the Wi-Fi connection, then turn on the fan. It will automatically oscillate its angle if enabling the oscillation function. The oscillation time varies depending on different angles, please wait with patience.
Set scheduled turn-off
Press the button to adjust the scheduled turn-off time. With each press, the scheduled turn-off time will cycle through 1 hour, 2 hours, 3 hours, 4 hours and disabled, and the corresponding status indicator(s) will be on. Five seconds after using the scheduled turn-off function, the status indicator will return to the corresponding status of the currently selected speed.
- Scheduled Status Indicator Status: Disabled ••••, 1 hour ••••, 2 hours ••••, 3 hours ••••, 4 hours ••••
Adjust the Airflow Direction
Gently lift or push down the fan's head or fan grille to adjust the airflow upwards or downwards. (23° upwards / 16° downwards)
Connect with the Mi Home App
This product works with Mi Home/Xiaomi Home app*. Control your device with Mi Home/Xiaomi Home app. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search "Mi Home/Xiaomi Home" in the app Store to download and install it. Open Mi Home/Xiaomi Home app, tap "+" on the upper right, and then follow prompts to add your device.
- *The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default.
- Note: The version of Mi Home app might have been updated, please follow the instructions based on the current app version.
Connecting to Wi-Fi
Simultaneously press and hold the buttons and . Once you hear a beep, the fan is awaiting a connection, then you can pair it with a device via the app.
- Wi-Fi Indicator Status: Awaiting connection (Blinking orange), Connecting (Blinking blue), Connected (Blue), Couldn't connect (Orange)
Daily Care & Maintenance
Clean the Fan
Parts that can be washed
The parts listed below can be cleaned with a soft cloth or sponge using water or neutral detergent.
- Front Grille
- Fan Blade Assembly
- Rear Grille
- Fan Grille Knob
- Note: Stop and unplug the fan, then disassemble it and clean its parts. After cleaning, make sure all parts are completely dry before installing them and using the fan again. Avoid direct sunlight.
Parts that cannot be washed
The parts listed below can be wiped clean with a soft dry cloth.
- Fan Blade Assembly Knob
- Base
- Motor & Stand
- Note: Do not use water to rinse the parts above. Do not use thinner, gasoline, detergent or alkaline detergent.
Reset Wi-Fi
The Wi-Fi connection needs to be reset on the circumstances listed in the table below.
- The Mi account that the fan is paired with has been changed.
- The router that the fan is connected to has been changed.
- The account or password of the router that the fan is connected to has been changed.
- The Mi Home/Xiaomi Home app cannot control the fan.
Simultaneously press and hold the buttons and . Once you hear a long beep, the Wi-Fi connection has been reset successfully and then the Wi-Fi is awaiting a connection.
Troubleshooting
Fault | Possible Causes | Solution |
---|---|---|
The fan doesn't work | No electricity from the power outlet or the fan does not connect to the power. | Connect to a power outlet that meets the fan's requirements. |
The power cable is not properly plugged into the fan's base. | Make sure the power cord is plugged in properly. | |
The fan stand and base are not properly installed. | Properly align the fan stand with the base and tighten the base bolt. | |
Wi-Fi is unable to connect | The Wi-Fi connection is 5 GHz. | Connect to a 2.4 GHz Wi-Fi connection. |
The fan is offline for more than half an hour. | Reset Wi-Fi (refer to instructions on resetting the Wi-Fi) | |
Fan blades are stuck | Fan blades are stuck by a foreign object. | Unplug the fan and remove the foreign object. |
The oscillation function does not work. | Motor error | Contact after-sales service |
The fan is under the auto-oscillation state. | Wait for the auto-oscillation completes. It will last for 14 seconds at most. |
Specifications
Name | Mi Smart Standing Fan 1X | Rated Voltage | 100-240 V~ | ||
---|---|---|---|---|---|
Model | BPLDS01XY | Rated Frequency | 50/60 Hz | ||
Type | DC standing fan | Rated Power | 15 W | ||
Gross Weight | 4.2 kg | Item Dimensions | 950×343×330 mm | ||
Net Weight | 2.8 kg | Noise Emission | <55 dB(A) | ||
Power Cord Length | 1.6 m | Wireless Connectivity | Wi-Fi IEEE 802.11b/g/n 2.4 GHz | ||
Blade of Fan | 7 | Number of Regulated Speed | 4 Speeds | ||
*Radio frequency and radio transmission power | |||||
RF Specification | 2.4G WIFI | Operation Frequency | 2412-2472MHz | Maximum Output Power | <20 dBm |
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
For detailed e-manual, please go to www.mi.com/global/service/userguide
Manufactured for: Xiaomi Communications Co., Ltd. Manufactured by: Zhejiang Xingyue Electric Equipment Co., Ltd. (a Mi Ecosystem company) Address: South Side, 24th Floor, Jinpin Building, Headquarters Center, Yongkang City, Zhejiang Province, China For further information, please go to www.mi.com V1.0
WARRANTY NOTICE
THIS WARRANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY HAVE OTHER RIGHTS CONVEYED BY LAWS OF YOUR COUNTRY, PROVINCE OR STATE. INDEED, IN SOME COUNTRIES, PROVINCES OR STATES, CONSUMER LAW MAY IMPOSE A MINIMUM WARRANTY PERIOD. OTHER THAN AS PERMITTED BY LAW, XIAOMI DOES NOT EXCLUDE, LIMIT OR SUSPEND OTHER RIGHTS YOU MAY HAVE. FOR A FULL UNDERSTANDING OF YOUR RIGHTS WE INVITE YOU TO CONSULT THE LAWS OF YOUR COUNTRY, PROVINCE OR STATE.
1. LIMITED PRODUCT WARRANTY
XIAOMI warrants that the Products are free from defects in materials and workmanship under normal use and use in accordance with the respective Product user manual, during the Warranty Period.
The duration and conditions related to the legal warranties are provided by respective local laws. For more information about the consumer warranty benefits, please refer to Xiaomi's official website https://www.mi.com/en/service/warranty/.
Xiaomi warrants to the original purchaser that its Xiaomi Product will be free from defects in materials and workmanship under normal use in the period mentioned above.
Xiaomi does not guarantee that the operation of the Product will be uninterrupted or error free.
Xiaomi is not liable for damages arising from non-compliance with the instructions related to the use of the Product.
2. REMEDIES
If a hardware defect is found and a valid claim is received by Xiaomi within the Warranty Period, Xiaomi will either (1) repair the product at no charge, (2) replace the product, or (3) refund the Product, excluding potential shipping costs.
3. HOW TO OBTAIN WARRANTY SERVICE
To obtain warranty service, you must deliver the Product, in its original packaging or similar packaging providing an equal degree of Product protection, to the address specified by Xiaomi. Except to the extent prohibited by applicable law, Xiaomi may require you to present proofs or proof of purchase and / or comply with registration requirements before receiving warranty service.
4. EXCLUSIONS AND LIMITATIONS
Unless otherwise stipulated by Xiaomi, this Limited Warranty applies only to the Product manufactured by or for Xiaomi and identifiable by the trademarks, trade name or "Xiaomi" or "Mi" logo.
The Limited Warranty does not apply to any (a) Damage due to acts of nature or God, for example, lightning strikes, tornadoes, flood, fire earthquake or other external causes; (b) Negligence; (c) Commercial use; (d) Alterations or modifications to any part of the Product; (e) Damage caused by use with non-Xiaomi products; (f) Damage caused by accident, abuse or misuse; (g) Damage caused by operating the Product outside the permitted or intended uses described by Xiaomi or with improper voltage or power supply; or (h) Damage caused by service (including upgrades and expansions) performed by anyone who is not a representative of Xiaomi.
It is your responsibility to backup any data, software, or other materials you may have stored or preserved on the product. It is likely that the data, software or other materials in the equipment will be lost or reformatted during the service process, Xiaomi is not responsible for such damage or loss.
No Xiaomi reseller, agent, or employee is authorized to make any modification, extension, or addition to this Limited Warranty. If any term is held to be illegal or unenforceable, the legality or enforceability of the remaining terms shall not be affected or impaired. Except as prohibited by laws or otherwise promised by Xiaomi, the after-sales services shall be limited to the country or region of the original purchase. Products which were not duly imported and/or were not duly manufactured by Xiaomi and/or were not duly acquired from Xiaomi or a Xiaomi's official seller are not covered by the present warranties. As per applicable law you may benefit from warranties from the non-official retailer who sold the product. Therefore, Xiaomi invites you to contact the retailer from whom you purchased the product.
5. IMPLIED WARRANTIES
Except to the extent prohibited by applicable law, all implied warranties (including warranties of merchantability and fitness for a particular purpose) will have a limited duration up to a maximum duration of this limited warranty. Some jurisdictions do not allow limitations on the duration of an implied warranty, so the above limitation will not be applied in these cases.
6. DAMAGE LIMITATION
Except to the extent prohibited by applicable law, Xiaomi shall not be liable for any damages caused by accidents, indirect, special or consequential damages, including but not limited to loss of profits, revenue or data, damages resulting from any breach of express or implied warranty or condition, or under any other legal theory, even if Xiaomi has been informed of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of special, indirect, or consequential damages, so the above limitation or exclusion may not apply to you.
7. XIAOMI CONTACTS
For customers, please visit the website: https://www.mi.com/en/service/warranty/. The contact person for the after-sale service may be any person in Xiaomi's authorized service network, Xiaomi's authorized distributors or the final vendor who sold the products to you. If in doubt please contact the relevant person as Xiaomi may identify.