Installation Manual

Thank you for choosing and using our product.

[QR Code for Installation Video]

[QR Code for App Control]

Tools Required

• Ladder
• Pliers
• Wire Strippers
• Screwdrivers

Packing List

Note: 1. Some extra hardware may be included. The quantity listed above is the number required for installation. 2. Parts "GG" have already been installed with Short Downrod Assembly, parts "DD" have been installed with Fan Motor Assembly. They need to be disassembled before installation.

Remote Control Instructions

Please insert 2 AAA 1.5V batteries (not included).

• ① Turn on/off the light.
• ② Turn on/off the fan.
• ③ Natural wind mode.
• ④ Turn on/off the mute mode.
• ⑤ 1/2/3/4/5/6 for Fan speed.
• ⑥ Turn off the fan (remote signal pairing).
• ⑦ Fan forward.
• ⑧ Fan reverse.
• 1H-4H for timing the fan.

Remote Signal Pairing

If the remote control loses the signal of the fan, turn off the power from the wall switch, then turn it on. Press ⑥ immediately for around 3 seconds. After the fixture beeps or flashes, then it's down.

Remote Diagram Description: The remote control has buttons labeled 1-6 for fan speed, F for forward, R for reverse, and 1H, 2H, 4H for timing. Other buttons control light, fan on/off, and natural/mute modes.

App Control Instructions

Note: Install the "Tiny Smart" app from Google Play, Apple App Store, or other app stores by scanning the QR code or searching for the app name. Ensure that your phone is connected to the internet and Bluetooth enabled.

Pairing

Add device → Follow the APP operation to turn off the wall switch, and turn it on after 5 seconds. The device will automatically connect to the Ceiling Fan.

App Functions

• Slide to adjust the Fan Speed (5 levels).
• Turn on/off the light.
• Turn on/off the fan.
• Turn off the fan and light (All Off).
• 1H-8H for timing the fan.
• Natural Wind: Simulates natural wind and automatically adjusts the wind speed.
• Fan forward & Fan reverse.

Installation

Step 1: Install the Mounting Bracket

Step 1. Take off the Set Screw and Nut from Mounting Bracket (EE).

Step 2. Secure the Mounting Bracket (EE) onto the Ceiling with Wood Screw with Washer (FF) and Anchor (FF).

Diagram Description: Illustrates attaching the mounting bracket (EE) to the ceiling using screws (FF) and anchors (FF). Shows the bracket, ceiling, screws, washers, and anchors.

Step 2: Assemble the Fan

Step 1. Assemble the Canopy and coupling cover, route wires from the fan through the downrod.

Step 2. Loosen the set screw from the yoke but do not take off, align the holes at the bottom of the downrod with those in the yoke.

Step 3. Carefully insert the clevis pin (GG) through the holes in the yoke and downrod (Be careful not to jam the clevis pin against the wires inside the downrod).

Step 4. Insert the "R" pin (GG) into the end of the clevis pin.

Step 5. Tighten the set screw on the yoke to secure the downrod.

Diagram Description: Shows the downrod being attached to the fan yoke. Illustrates loosening a set screw, inserting a clevis pin (GG) and an "R" pin (GG) to secure the downrod to the yoke.

Step 3: Hanging the Fan and Locking the Hanging Wire

Step 1. Lift the downrod into the Mounting Bracket. Rotate the downrod until the seat tab in the mounting bracket is seated in the groove in the downrod ball.

Step 2. Fix the Set Screw and Nut onto the Mounting Bracket.

Step 3. Wrap the Hanging Wire around the side of the mounting bracket and thread it through the lock to secure it.

Step 4. Pull on the hanging wire strands to tighten them in place and secure it with screws.

Diagram Description: Depicts the fan downrod ball fitting into the mounting bracket. Shows the set screw and nut securing the bracket, and the hanging wire being wrapped and secured.

Step 4: Wiring

Step 1. Insert the receiver into the mounting bracket.

Step 2. Connect the wires from the fixture to the house supply wires with wire nuts (AA): ground wire (green, green/yellow, or bare copper) to ground wire, neutral wire (white or blue) to neutral wire, and hot wire (black or brown) to the hot wire.

Step 3. Wrap the connection with electrical tape.

Diagram Description: Shows the receiver being placed in the mounting bracket. A simplified wiring diagram illustrates connecting the green (ground), white (neutral), and black (hot) wires from the fixture to the corresponding house supply wires using wire nuts (AA).

Note:

• This fan only needs one set of input wires (black, white, and ground wire). Both the fan and lights will be controlled by the remote control.
• This fan can only be connected to an on/off switch if you have one, not a dimmer switch.

Step 5: Attaching the Canopy

Step 1. Slide the canopy up to the ceiling and attach it to the mounting bracket with the set screws provided.

Step 2. Slide the coupling cover downward to cover the yoke and fix the canopy ring to the canopy.

Diagram Description: Shows the canopy being slid up to the ceiling and secured with set screws. The coupling cover is then slid down to conceal the yoke, and the canopy ring is attached.

Step 6: Installing the Fan Blade and Blade Arm

Step 1. Attach fan blade onto the Blade Arms A and Blade Arms B with Fan Blade Screws (BB) provided.

Step 2. Insert the end of the Fan Blade into the Blade Cover and secure it with Blade Cover Screw (HH).

Step 3. Take off Fan Blade Arm Screws (DD) from the Fan Motor Assembly.

Step 4. Attach the Fan Blade Arm onto the motor with the Fan Blade Arm Screws taken off.

Diagram Description: Illustrates attaching fan blades (N) to blade arms (M, P) using screws (BB). Then, the blade assembly is attached to a blade cover (O) with screws (HH). Finally, the blade arms are attached to the fan motor assembly (F) using screws (DD).

Note: Make sure to assemble the blades in sequence and fasten the screws with equal force.

Step 7: Install the Light Kit Mounting Plate

Step 1. Take off the Set Screws from the Fan Motor Assembly.

Step 2. Secure the Light Kit Mounting Plate onto the Fan Motor Assembly with screws taken off.

Diagram Description: Shows the fan motor assembly. Set screws are removed, and the light kit mounting plate is attached to the motor assembly using these screws.

Step 8: Install the LED Light Kit and Light Shade

Step 1. Connect the Light Wire terminal to the interface on the LED Light Kit.

Step 2. Rotate the Light Shade clockwise to secure it to the Light Kit Mounting Plate.

Diagram Description: Depicts connecting the light wire to the LED light kit. The light shade is then attached to the light kit mounting plate by rotating it clockwise.