Instruction Manual for Home Depot models including: FS-8836D-52-01, FS6930-01-02, FS-8836D Ceiling Fan with Light, Ceiling Fan with Light, Fan with Light, Light
1 день назад — Pairing: Add device→→ Followthe APP operation to tumoff the wall switch, and tum it on after 5 seconds. The device will automatically connect to the Ceiling Fan ...
1 day ago — MANUAL. CEILING FAN WITH LIGHT. Model No.: FS-8836D-52-01. Page 2. F. R. 1H. 4H. | Short Downrod x1. J Remote Control with Holder×1. K Fan Blade ×5. L Blade Arm ...
mutemode 1/2/3/4/5/6 for 1H- ALL OFF LIGHT ON/OFF 2 1 3 FAN/OFF 6 4 5 F R 1H 2H 4H INSTALLATION MANUAL CEILING FAN WITH LIGHT Model No.: FS-8836D-52-01 Note: Installthe"TinySmart" appfromGooglePlay,AppleAppStore,orotherappstoresbyscanningtheQRcode orsearchingfortheappname. Ensurethatyourphoneisconnectedtotheinternetand Bluetoothenabled. Pairing: Adddevice FollowtheAPPoperationtoturnoffthewallswitch,andturnitonafter5seconds. Thedevicewill automaticallyconnect totheCeiling Fan. SlidetoadjusttheFanSpeed. Turnon/offthelight. Turn on/offthefan. Turnoff thefan and light. 1H-8H fortimingthefan. NaturalWind:Simulate naturalwindandautomaticallyadjustthewindspeed. Fan forward& Fanreverse. ALL OFF LIGHT ON/OFF 2 1 3 FAN /O F F 6 4 5 F R 1H 2H 4H I Short Downrod ×1 J RemoteControlwithHolder×1 K Fan Blade×5 L BladeArm ×5 INSTALLATION KIT 3 15 Fan BladeScrew A Receiver ×1 B Canopy×1 C CanopyRing×1 D Long DownrodAssembly×1 E CouplingCover ×1 F Fan MotorAssembly ×1 G LightShade ×1 H LightKit ×1 10 Fan BladeArmScrew Mounting Bracket OutletBox ScrewWithWasher Clevis Pin&"R" Pin Nipple Kit NOTE: 1.Someextra hardwaremay be included.Thequantity listed above isthe number requiredfor installation. 2. Parts "GG"havealreadybeen installedwith Long DownrodAssembly , parts"DD" havebeen installed with Fan MotorAssembly.They needto be disassembled before installation. 9. Install the Light Kit Step 1.Connectthe LightWiresfromthe LightKittothe fixturewires. Step2. FixtheLightKitontotheLightShade(theNipplepassesthroughtheLightKit). LightWire LightKit 10. Install the Nipple Kit and Bulbs Step 1.ThreadtheNipplethroughtheholeintheCoverandsecureitwithNut. Step 2. Install2E26Bulbsnotexceeding60W. Nipple Hole Cover Nut 7. Install the Light Shade Step 1. TakeofftheSetScrewsfromthe FanMotorAssembly. Step2.RotatetheLightKitcounter clockwise and remove it from the Light Shade. Step3.Attach the LightShadeontothe Fan MotorAssemblywith screws taken off. 8. Attaching the Nipple Step 1.Attachthe Nipple(HH) inthe Fan MotorAssembly. LightShade Set Screw Light Kit Nipple 1. Installing the Mounting Bracket Step 1. Take offthescrewsfromoutletbox. Step2.Securethemountingbracket(EE)onto theoutletboxwithscrewstakenofforOutletBoxScrewWithWasher(FF)provided. MountingBracket(EE) OutletBoxScrew WithWasher(FF) 2.Assembling the Fan Step 1.AssembletheCanopyandcouplingcover, route wires from the fan through the downrod. Step 2. Loosen the set screw from the yokebut do not take off, align the holes at the bottom of the downrod with those in the yoke. Step 3. Carefully inserttheclevis pin (GG)throughtheholes intheyokeand downrod (Be careful not tojamthe clevis pin against the wires inside the downrod). Step4. Insertthe "R"pin (GG) intotheend ofthe clevis pin. Step 5.Tightenthesetscrewontheyoketosecurethe downrod. Downrod Set Screw Yoke "R"pin (GG) ClevisPin (GG) 3. Hanging the Fan Step 1. Liftthedownrodintothemountingbracket. Rotatethedownrod until the seat tab in the mounting bracket is seated in the groove in the downrod ball. Seat Tab Mounting Bracket Groove DownrodBal 4. Wring Step 1. Insertthe receivertothemountingbracket Step2.Connectthewires from thefixturetothe house supply wires with wire nuts (AA) , ground wire (green, green/yellow, or bare copper) to ground wire, neutral wire (whiteorblue)toneutralwire,and hot wire (black or brown) to the hot wire. Step3.Wraptheconnectionwithelectrical tape. Note: Thisfanonlyneedsone setof inputwires(black, white,and ground wire). Both of the fan and lightswill be controlled by the remote control. Thisfancanonlybe connected to anon/offswitchifyou have one, not a dimmer switch. 5. Attaching the Canopy Step 1.Slidethecanopyuptotheceiling and attach itto the mounting bracket with the set screws provided. Step2.Slidethecouplingcoverdownwardto cover the yoke andfixthecanopyringtothecanopy. Set Screw CanopyRing CouplingCover 6. Installing the Fan Blade and Blade Arm Step 1.Attachfanbladeontotheblade arms with Fan Blade Screws (BB) provided. Step2.Takeoff Fan BladeArm Screws (DD)fromthe Fan Motor Assembly. Step3.Attachthe Fan BladeArmontothe motorwith the Fan Blade Arm Screws taken off. Fan BladeScrew (BB) Fan Blade ArmScrew(DD)WPS 文字