SpiderENTRY S23 Access Control Keypad Installation Guide

Step 1: Unpack and Verify Contents

Unpack the box and ensure all items shown are present:

• SpiderENTRY Keypad
• Nuts & Bolts (for mounting)
• 2 sets of Keys (for manager override)
• Power Adapter (12-24 volts DC)

The Power Adapter is rated for 12-24 volts DC.

Step 2: Mount and Wire the Keypad

Unlock and open the front door of the unit to install and wire it. The door swings forward.

Closed position [Keypad shown in closed state]

Open position [Keypad shown in open state, revealing internal wiring]

Mount the keypad box to the pedestal using the four holes on the back of the box. Four bolts and four nuts are provided.

Ensure the CAT5 wire is pulled through the opening in the middle of the box.

WARNING: AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH! ALWAYS CHECK THAT THE GATE PATH IS CLEAR PRIOR TO OPENING! SAFETY REVERSING DEVICES SHOULD ALWAYS BE USED!

Step 3: Connect to Gate Motor Relay

The relay wire from your gate motor should connect to the green relay input labeled "GATE". This connection signals the gate to open when a valid code is entered.

[Diagram description: Shows a circuit board with a green terminal labeled "GATE". A wire is shown connecting from a gate motor to this terminal.]

Step 4: Connect Power

Connect the power supply to the green input labeled "GND / V+". This connection should be made using the supplied adapter to ensure the proper voltage.

Note: The keypad is designed to handle voltages between 12V and 24V only. Voltages outside this range are not supported. Improper power installation may void the warranty and damage the unit.

[Diagram description: Shows a circuit board with a green terminal labeled "GND / V+". Wires from a power adapter are shown connecting to this terminal.]

Step 5: Manager Override Key

The key switch on the side of the unit serves as a manager override. By turning the key clockwise a half turn, managers can physically open the gate.

This function bypasses the keypad's code entry and directly activates the gate motor to open and stay open. The gate will remain open until the key is turned back counterclockwise a half turn.

NOTE: If the override key is left turned clockwise during installation, the gate may remain in the open position.

[Diagram description: Shows the side of the keypad with a key inserted and turned. Text indicates "Managers Override Key" and "This switch will allow a manager to open the gate with a key."]

Step 6: Connect Magnetic Lock (Optional)

For walk-through doors using a magnetic lock, connect to the green input labeled "Mag Lock (N/C and common)".

Connect the magnetic lock wires to the normally closed (N/C) and common ports on the lock.

[Diagram description: Shows a circuit board with a green terminal labeled "Mag Lock". Wires are shown connecting to this terminal and then to a magnetic lock.]

Keypad Sound Codes:

ACTIVE CODE: A solid 4-second buzz indicates a successfully entered code.

INACTIVE CODE: Three short beeps signify that a code is inactive or invalid.

Required Action

REQUIRED: Visit www.Spiderdoor.com to "Request Install" 24 hours in advance, or email Support@Spiderdoor.com.

Compliance Information

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Product Name: Access Control Keypad

Product Model: S23, S33

Manufacturer: Spiderdoor

Address: 2284 Brock Circle, Birmingham, Alabama 35242

Contact: xxx@spiderdoor.com | www.spiderdoor.com

Modular Components Used:

• NAME: nRF91
• MODEL: nrRF9160
• FCC ID: 2ANPO00NRF9160

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure statement

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 30cm between the radiator and any part of your body.

Canadian Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : L'appareil ne doit pas produire de brouillage; L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

RF exposure statement (Canada)

This equipment meets the exemption from the routine evaluation limits in section 6 of RSS-102. It should be installed and operated with a minimum distance of 30cm between the radiator and any part of your body. Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 6 de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 30 cm entre le radiateur et toute partie de votre corps.