Installation Guide
TrueForce Core LED road lamp
Please take the time to read this installation guide. The guide contains important information and notes regarding the installation and operation.
IMPORTANT!
- Always switch off the power supply before commencing work!
- Please read the installation instructions carefully and follow the wiring instructions to ensure safety.
- The product is NOT dimmable.
- The product can be operated on Direct Mains or Electro Magnetic (EM) gear without ignitor. Ignitor ALWAYS needs to be disconnected from the system.
- Recommended to remove capacitor to improve system power factor.
- The product is not compatible with electronic gear.
- Suitable for use in operating temperature range between -40°C to +45°C.
- Do not change the structure or any components of the product to ensure safety.
- The product is designed to fit in standard IEC compliant E27/E40 lamp holders.
- The product should be installed by qualified professional.
- Perform inspection before installation to ensure the luminaire and lamp holder are in good condition to carry the weight and performance of the product.
- Do not use in open luminaire.
- The product fulfills IP65 requirements except lamp cap, outdoor applications require the lamp to be used in luminaires with suitable IP rating.
- Please do not apply the product in applications which contains emergency or/and explosive proof luminaires.
- The total system performance may vary depending on the lighting/luminaire system.
- For latest information, please refer to www.philips.com/lighting.
- In case of doubt, please consult Philips representative.
DISCLAIMER
Signify disclaims liability for any direct, indirect or incidental damages in case of installation performed either not according to this guide or not performed by a professional electrician.
For replacing HPL/SON/Other Lamps, Convert to Direct Mains (Recommended)
Diagrams illustrate converting to direct mains power for HPL/SON/Other lamps. Steps include switching off power, disconnecting existing ballast/ignitor wires, connecting directly to mains, inserting the new LED lamp, and switching power back on. A warning sticker is shown, and the final state is with power ON.
Steps:
- 1 Switch power OFF.
- 2 Disconnect existing ballast/ignitor wires.
- 3 Connect wires directly to mains power.
- 4 Screw in the new LED lamp.
- 5 Apply warning sticker.
- 6 Switch power ON.
Note: Ensure open wires are properly terminated after disconnection. If a capacitor is left connected, the power factor may be lower.
For replacing HPL Lamps and keeping the EM ballast
Diagrams illustrate replacing HPL lamps while keeping the Electromagnetic (EM) ballast. Steps involve switching off power, disconnecting the capacitor (optional), connecting wires to the ballast, inserting the LED lamp, and switching power on. Notes mention proper termination of disconnected wires and potential lower power factor if the capacitor is not removed.
Steps:
- 1 Switch power OFF.
- 2 Disconnect capacitor (optional).
- 3 Connect wires to the EM ballast.
- 4 Screw in the new LED lamp.
- 5 Apply warning sticker.
- 6 Switch power ON.
Note: Ensure open wires are properly terminated after disconnection. If a capacitor is left connected, the power factor may be lower.
For replacing SON Lamps and keeping the EM ballast
Diagrams illustrate replacing SON lamps while keeping the Electromagnetic (EM) ballast. Steps include switching off power, disconnecting wires from both the ignitor and capacitor (optional), connecting wires to the ballast, inserting the LED lamp, and switching power on. Notes emphasize proper termination of disconnected wires and the potential for a lower power factor if the capacitor is not removed.
Steps:
- 1 Switch power OFF.
- 2 Disconnect ignitor and capacitor (optional).
- 3 Connect wires to the EM ballast.
- 4 Screw in the new LED lamp.
- 5 Apply warning sticker.
- 6 Switch power ON.
Note: Ensure open wires are properly terminated after disconnection. If a capacitor is left connected, the power factor may be lower.
[CE mark] [RoHS Compliant] [IP65 rating]
[Philips logo]
© 2021 Signify Holding. All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.
Publication Date: 04/2021. For latest information, please visit www.philips.com/lighting.
Document reference: 3241 658 24591
