MRCOOL Remote Control User Manual

Remote Controller Specifications & Quick Start Guide

Quick Start Guide

Follow these steps for basic operation:

1. FIT BATTERIES: Insert batteries into the remote control.
2. SELECT MODE: Press the MODE button to cycle through AUTO, COOL, DRY, HEAT, and FAN modes.
3. SELECT TEMPERATURE: Use the UP (&and#8593;) and DOWN (&and#8595;) arrow buttons to set the desired temperature.
4. SELECT FAN SPEED: Press the FAN button to choose between AUTO, LOW, MED, or HIGH fan speeds.
5. POINT REMOTE TOWARD UNIT: Ensure the remote is aimed at the indoor unit.
6. PRESS POWER BUTTON: Press the ON/OFF (&power-symbol;) button to turn the unit on or off.

NOT SURE WHAT A FUNCTION DOES? Refer to the 'How to Use Basic Functions' and 'How to Use Advanced Functions' sections for detailed instructions.

SPECIAL NOTE:

• Button designs on your remote may differ slightly from the examples shown.
• If the indoor unit is not equipped with a particular function, pressing the corresponding button on the remote will have no effect.
• In case of differences between this 'Remote Controller Manual' and the 'USER'S MANUAL' regarding function descriptions, the 'USER'S MANUAL' description takes precedence.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries. Install the batteries in the remote control before use by following these steps:

1. Slide the back cover from the remote control downward to expose the battery compartment.
2. Insert the batteries, ensuring the (+) and (-) designations on the batteries match the symbols inside the battery compartment.
3. Reinstall the back cover by sliding it back into place.

BATTERY NOTES

• For optimum product performance: DO NOT mix old and new batteries, or batteries of different types.
• DO NOT leave batteries in the remote control if the device will not be used for more than 2 months.

BATTERY DISPOSAL

DO NOT dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 26 ft (8 m) of the unit.
• The unit will beep when a remote signal is received.
• Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used for more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device should comply with local national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In the USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.

Easy Pro^® & Olympus Series Remote Controller

Buttons and Functions

Familiarize yourself with the remote control. For operating instructions, refer to the 'How to Use Basic Functions' section.

• ON/OFF (&power-symbol;): Turns the unit on or off.
• TEMP (&and#8593;): Increases temperature in 1°F (1°C) increments. Maximum setting is 86°F (30°C). Pressing TEMP UP (&and#8593;) and DOWN (&and#8595;) buttons together for 3 seconds alternates temperature display between °C and °F.
• SET: Scrolls through operation functions: Sleep (&sleep-symbol;), Follow Me (&person-symbol;), AP Mode (&wifi-symbol;). The selected symbol flashes; press OK to confirm.
• TEMP (&and#8595;): Decreases temperature in 1°F (1°C) increments. Minimum setting is 60°F (16°C).
• FAN SPEED: Selects fan speeds: AUTO, 20%, 40%, 60%, 80%, 100%. Press TEMP UP/DOWN to adjust fan speed in 1% increments.
• SWING: Starts and stops horizontal louver movement. Hold for 2 seconds for vertical louver auto swing (model dependent).
• MODE: Cycles through modes: AUTO, COOL, DRY, HEAT, FAN. HEAT mode is not supported by cooling-only versions.
• ECO/GEAR: Enters energy-efficient modes: ECO, GEAR (75%), GEAR (50%), Previous setting mode.
• OK: Confirms selected functions.
• TIMER (&timer-symbol;): Sets the timer to turn the unit on or off at a specified time.
• BREEZE AWAY: Directs airflow away from occupants. Available in COOL, FAN, and DRY modes.
• CLEAN: Starts/stops the Self-Clean or Active Clean function (model dependent). Refer to the USER'S MANUAL for details.
• LED: Turns the indoor unit's LED display and buzzer on/off (model dependent) for a quiet environment.
• TURBO: Enables the unit to reach the preset temperature quickly.

Remote Screen Indicators

Information displayed when the remote controller is turned on:

• Transmission (&signal-symbol;): Lights up when the remote transmits a signal.
• TIMER ON/OFF (&timer-symbol;): Indicates timer status.
• Silence (&wind-blowing-symbol;): Lights up when the Silence function is activated.
• FAN SPEED: Displays selected fan speed (Silence, LOW, MED, HIGH, AUTO). Note: Fan speed cannot be adjusted in AUTO or DRY mode.
• MODE display: Shows the current mode (AUTO, COOL, DRY, HEAT, FAN).
• ECO display: Shows when ECO feature is activated.
• GEAR display: Shows when GEAR feature is activated.
• LOCK display: Shows when LOCK feature is activated.
• Temperature/Timer/Fan speed display: Shows set temperature, fan speed, or timer setting.
• Breeze Away display (&star-symbol;): (some units)
• Follow me feature display (&person-symbol;):
• Wireless control feature display (&wifi-symbol;): (some units)
• Low battery detection display: Flashes when batteries are low.

NOTE: All indicators shown are for demonstration. Only active functions display during operation.

How to Use Basic Functions

ATTENTION: Ensure the unit is plugged in and power is available before operation.

AUTO Mode

1. Press MODE button and select AUTO.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: In AUTO mode, the unit automatically selects COOL, FAN, or HEAT based on the set temperature. Fan speed cannot be set or adjusted by the user.

COOL or HEAT Mode

1. Press MODE button and select COOL or HEAT.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press FAN button to select desired fan speed (AUTO, LOW, MED, HIGH).
4. Press ON/OFF (&power-symbol;) to start the unit.

SETTING TEMPERATURE: The operating temperature range is 62-86°F (17-30°C) or 68-82°F (20-28°C) (model dependent). Use TEMP UP/DOWN buttons for 1°F (1°C) increments.

DRY Mode

1. Press MODE button and select DRY.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: In DRY mode, fan speed is automatically controlled and cannot be set.

FAN Mode

1. Press MODE button and select FAN.
2. Press FAN button to select desired fan speed (AUTO, LOW, MED, HIGH).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: Temperature cannot be set or adjusted in FAN mode. The remote display will not show temperature.

Setting the TIMER

Use the TIMER (&timer-symbol;) button to set the unit to automatically turn on or off at a specified time.

TIMER ON setting

1. Press the TIMER (&timer-symbol;) button to initiate the ON time sequence.
2. Press the TEMP UP (&and#8593;) or DOWN (&and#8595;) button to set the desired ON time.
3. Point the remote control at the unit and wait 1 second for TIMER ON to activate.

TIMER OFF setting

1. Press the TIMER (&timer-symbol;) button to initiate the OFF time sequence.
2. Press the TEMP UP (&and#8593;) or DOWN (&and#8595;) button to set the desired OFF time.
3. Point the remote control at the unit and wait 1 second for TIMER OFF to activate.

NOTE:

• When setting TIMER ON or OFF, time increases in 30-minute increments up to 10 hours, then in 1-hour increments up to 24 hours. The timer resets to 0.0 after 24 hours.
• Cancel either function by setting its timer to 0.0 h.

TIMER ON & OFF setting (example)

NOTE: Time periods set refer to hours after the current time.

Example: If the current time is 1:00 PM, setting the timer for 2.5 hours ON and 5 hours OFF means the unit will turn ON at 3:30 PM and turn OFF at 6:00 PM.

How To Use Advanced Functions

Swing function

Press the SWING button. The horizontal louver will swing up and down. Press again to stop. Holding the SWING button for over 2 seconds activates vertical louver swing (model dependent).

Airflow direction

Pressing the SWING button repeatedly allows selection of five different airflow directions. The louver moves to a new angle with each press. Continue pressing until the desired setting is reached.

NOTE: When the unit is off, press and hold MODE and DOWN buttons simultaneously for 3 seconds to access panel setting mode (display shows F2). Use UP/DOWN buttons to raise/lower the air intake panel for filter maintenance. Press any button to exit. Refer to the Care & Maintenance section for details.

LED Display

Press the LED button to turn the indoor unit's LED display and buzzer on or off (model dependent).

Press and hold the LED button for over 5 seconds (some units) to display the actual room temperature. Press and hold again to revert to the set temperature display.

ECO/GEAR function

Pressing the ECO/GEAR button cycles through energy efficiency modes: ECO, GEAR (75%), GEAR (50%), Previous setting mode.

• ECO operation: In COOL mode, if the set temperature is below 75°F (24°C), the unit adjusts the temperature to 75°F (24°C) and sets fan speed to AUTO to save energy. If the set temperature is above 75°F (24°C), the fan speed changes to AUTO, and the temperature remains unchanged.
• NOTE: ECO operation stops if the ECO/GEAR button is pressed again, the mode is changed, or the set temperature is adjusted below 75°F (24°C). For insufficient cooling under ECO operation, press the ECO button again to turn it off.
• GEAR operation: Selects up to 75% or 50% electrical energy consumption. The display alternates between energy consumption and set temperature.

Silence function

Pressing the FAN button for over 2 seconds activates/deactivates the Silence function (some units). This function may result in reduced cooling/heating capacity due to low-frequency compressor operation. Pressing ON/OFF, MODE, SLEEP, TURBO, or CLEAN cancels Silence mode.

FP function

For heat pump units: Press the button twice within one second while in HEAT Mode. The temperature sets to 60°F (16°C) or 68°F (20°C) (model dependent), activating FP function for faster heating. This function uses high fan speed and the lowest temperature setting (46°F/8°C) for faster cooling. Pressing ON/OFF, SLEEP, MODE, FAN, or Temperature buttons cancels FP mode.

LOCK function

Press CLEAN and TURBO buttons simultaneously for over 5 seconds to activate LOCK. No buttons will respond until both are pressed again for 2 seconds to disable LOCK.

Clean Function (some units)

Press the CLEAN button to start/stop the Self-Clean or Active Clean function. This function cleans the unit automatically to remove moisture, dust, mold, and grease, improving efficiency. After cleaning, the unit turns off. Pressing CLEAN mid-cycle cancels the operation. This function is available only in COOL or DRY mode.

TURBO Function

Press the TURBO button. In COOL mode, the unit blows cool air at the highest fan setting for faster cooling. In HEAT mode, it blows warm air at the highest fan setting for faster heating (some units), or activates electric heaters if equipped.

SET function

Press the SET button to enter function settings. Use SET, TEMP UP (&and#8593;), or TEMP DOWN (&and#8595;) to select a function (e.g., Breeze Away (&star-symbol;), Active Clean (&wind-blowing-symbol;), Follow Me (&person-symbol;), AP Mode (&wifi-symbol;)). The selected symbol flashes; press OK to confirm and activate. Repeat to cancel.

• Breeze Away function (&star-symbol;): Keeps airflow from blowing directly on occupants. Available in COOL, FAN, and DRY modes.
• Active Clean function (&wind-blowing-symbol;): Cleans the heat exchanger by producing condensate, freezing it, then thawing to wash away debris. 'CL' appears on the display. Operation lasts 20-45 minutes, then the unit turns off.
• AP function (&wifi-symbol;): For wireless network configuration. For some units, press LED button seven times within 10 seconds to enter AP mode.
• Follow me function (&person-symbol;): The remote measures and sends the ambient temperature to the unit every 3 minutes, optimizing temperature control at your location. Press and hold TURBO for 7 seconds to start/stop the memory feature (displays 'ON' or 'OF'). This function is not canceled by ON/OFF, mode changes, or power failure when activated.

Buttons and Functions

Familiarize yourself with the remote control. For operating instructions, refer to the 'How to Use Basic Functions' section.

• ON/OFF (&power-symbol;): Turns the unit on or off.
• TEMP &and#8593;: Increases temperature in 1°F (1°C) increments. Maximum setting is 86°F (30°C). Pressing TEMP UP (&and#8593;) and DOWN (&and#8595;) buttons together for 3 seconds alternates temperature display between °C and °F.
• SET: Scrolls through operation functions: Breeze Away (&star-symbol;), Active Clean (&wind-blowing-symbol;), Follow Me (&person-symbol;), AP Mode (&wifi-symbol;). The selected symbol flashes; press OK to confirm.
• TEMP &and#8595;: Decreases temperature in 1°F (0.5°C) increments. Minimum setting is 60°F (16°C).
• FAN SPEED: Selects fan speeds: AU, 20%, 40%, 60%, 80%, 100%. Press TEMP UP/DOWN to adjust fan speed in 1% increments.
• SWING: Starts and stops horizontal louver movement.
• MODE: Cycles through modes: AUTO, COOL, DRY, HEAT, FAN. HEAT mode is not supported by cooling-only versions.
• SLEEP (&sleep-symbol;): Saves energy during sleeping hours. Not available in FAN or DRY mode.
• OK: Confirms selected functions.
• TIMER (&timer-symbol;): Sets the timer to turn the unit on or off at a specified time.
• ECO/GEAR: Enters energy-efficient modes: ECO, GEAR (75%), GEAR (50%), Previous setting mode.
• HUMIDITY: Adjusts room humidity during DRY operation (35%-85%) in 5% increments.
• LED: Turns the indoor unit's LED display and buzzer on/off (model dependent).
• TURBO: Enables the unit to reach the preset temperature quickly.

Remote Screen Indicators

Information displayed when the remote controller is turned on:

• Transmission (&signal-symbol;): Lights up when the remote transmits a signal.
• TIMER ON/OFF (&timer-symbol;): Indicates timer status.
• Silence (&wind-blowing-symbol;): Lights up when the Silence function is activated.
• FAN SPEED: Displays selected fan speed (Silence, LOW, MED, HIGH, AUTO). Note: Fan speed cannot be adjusted in AUTO or DRY mode.
• MODE display: Shows the current mode (AUTO, COOL, DRY, HEAT, FAN).
• ECO display: Shows when ECO feature is activated.
• GEAR display: Shows when GEAR feature is activated.
• LOCK display: Shows when LOCK feature is activated.
• Temperature/Timer/Fan speed display: Shows set temperature, fan speed, or timer setting. Temperature range: 60-86°F (16-30°C). Timer setting range: 0-24 hours. Fan speed setting range: AU - 100%. Humidity setting range: 35%-85%. Display is blank in FAN mode.
• Breeze Away display (&star-symbol;): (some units)
• Active clean feature display (&wind-blowing-symbol;):
• Sleep mode display (&sleep-symbol;):
• Follow me feature display (&person-symbol;):
• Wireless control feature display (&wifi-symbol;): (some units)
• Low battery detection display: Flashes when batteries are low.

NOTE: All indicators shown are for demonstration. Only active functions display during operation.

How to Use Basic Functions

ATTENTION: Ensure the unit is plugged in and power is available before operation.

AUTO Mode

1. Press MODE button and select AUTO.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: In AUTO mode, the unit automatically selects COOL, FAN, or HEAT based on the set temperature. Fan speed cannot be set or adjusted by the user.

COOL or HEAT Mode

1. Press MODE button and select COOL or HEAT.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press FAN button to select desired fan speed (AUTO, LOW, MED, HIGH).
4. Press ON/OFF (&power-symbol;) to start the unit.

DRY Mode

1. Press MODE button and select DRY.
2. Set desired temperature using TEMP UP (&and#8593;) or DOWN (&and#8595;).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: In DRY mode, fan speed is automatically controlled and cannot be set.

FAN Mode

1. Press MODE button and select FAN.
2. Press FAN button to select desired fan speed (AUTO, LOW, MED, HIGH).
3. Press ON/OFF (&power-symbol;) to start the unit.

NOTE: Temperature cannot be set or adjusted in FAN mode. The remote display will not show temperature.

Setting the TIMER

Use the TIMER (&timer-symbol;) button to set the unit to automatically turn on or off at a specified time.

TIMER ON setting

1. Press the TIMER (&timer-symbol;) button to initiate the ON time sequence.
2. Press the TEMP UP (&and#8593;) or DOWN (&and#8595;) button to set the desired ON time.
3. Point the remote control at the unit and wait 1 second for TIMER ON to activate.

TIMER OFF setting

1. Press the TIMER (&timer-symbol;) button to initiate the OFF time sequence.
2. Press the TEMP UP (&and#8593;) or DOWN (&and#8595;) button to set the desired OFF time.
3. Point the remote control at the unit and wait 1 second for TIMER OFF to activate.

NOTE:

• When setting TIMER ON or OFF, time increases in 30-minute increments up to 10 hours, then in 1-hour increments up to 24 hours. The timer resets to 0.0 after 24 hours.
• Cancel either function by setting its timer to 0.0 h.

TIMER ON & OFF setting (example)

NOTE: Time periods set refer to hours after the current time.

Example: If the current time is 1:00 PM, setting the timer for 2.5 hours ON and 5 hours OFF means the unit will turn ON at 3:30 PM and turn OFF at 6:00 PM.

How To Use Advanced Functions

Swing function

Press the SWING button. The horizontal louver will swing up and down. Press again to stop. Holding the SWING button for over 2 seconds activates vertical louver swing (model dependent).

Airflow direction

Pressing the SWING button repeatedly allows selection of five different airflow directions. The louver moves to a new angle with each press. Continue pressing until the desired setting is reached.

NOTE: When the unit is off, press and hold MODE and DOWN buttons simultaneously for 3 seconds to access panel setting mode (display shows F2). Use UP/DOWN buttons to raise/lower the air intake panel for filter maintenance. Press any button to exit. Refer to the Care & Maintenance section for details.

LED Display

Press the LED button to turn the indoor unit's LED display and buzzer on or off (model dependent).

Press and hold the LED button for over 5 seconds (some units) to display the actual room temperature. Press and hold again to revert to the set temperature display.

ECO/GEAR function

Pressing the ECO/GEAR button cycles through energy efficiency modes: ECO, GEAR (75%), GEAR (50%), Previous setting mode.

• ECO operation: In COOL mode, if the set temperature is below 75°F (24°C), the unit adjusts the temperature to 75°F (24°C) and sets fan speed to AUTO to save energy. If the set temperature is above 75°F (24°C), the fan speed changes to AUTO, and the temperature remains unchanged.
• NOTE: ECO operation stops if the ECO/GEAR button is pressed again, the mode is changed, or the set temperature is adjusted below 75°F (24°C). For insufficient cooling under ECO operation, press the ECO button again to turn it off.
• GEAR operation: Selects up to 75% or 50% electrical energy consumption. The display alternates between energy consumption and set temperature.

Silence function

Pressing the FAN button for over 2 seconds activates/deactivates the Silence function (some units). This function may result in reduced cooling/heating capacity due to low-frequency compressor operation. Pressing ON/OFF, MODE, SLEEP, TURBO, or CLEAN cancels Silence mode.

FP function

For heat pump units: Press the button twice within one second while in HEAT Mode. The temperature sets to 60°F (16°C) or 68°F (20°C) (model dependent), activating FP function for faster heating. This function uses high fan speed and the lowest temperature setting (46°F/8°C) for faster cooling. Pressing ON/OFF, SLEEP, MODE, FAN, or Temperature buttons cancels FP mode.

LOCK function

Press TURBO and HUMIDITY buttons simultaneously for over 5 seconds to activate LOCK. No buttons will respond until both are pressed again for 2 seconds to disable LOCK.

Sleep Function

Press the SLEEP (&sleep-symbol;) button. The SLEEP function reduces energy use during sleep. Temperature settings for comfort during sleep differ from awake settings. This function can only be activated via the remote control. Refer to the Sleep Operation section of your unit's USER MANUAL for details. The SLEEP function is not available in FAN or DRY mode.

TURBO Function

Press the TURBO button. In COOL mode, the unit blows cool air at the highest fan setting for faster cooling. In HEAT mode, it blows warm air at the highest fan setting for faster heating (some units), or activates electric heaters if equipped.

SET function

Press the SET button to enter function settings. Use SET, TEMP UP (&and#8593;), or TEMP DOWN (&and#8595;) to select a function (e.g., Breeze Away (&star-symbol;), Active Clean (&wind-blowing-symbol;), Follow Me (&person-symbol;), AP Mode (&wifi-symbol;)). The selected symbol flashes; press OK to confirm and activate. Repeat to cancel.

• Breeze Away function (&star-symbol;): Keeps airflow from being blown directly on the occupants of the room. Available in COOL, FAN, and DRY modes.
• Active Clean function (&wind-blowing-symbol;): The ACTIVE CLEAN function cleans the heat exchanger by producing condensate, freezing it, then thawing to wash away debris. 'CL' appears on the display. Operation lasts 20-45 minutes, then the unit turns off.
• AP function (&wifi-symbol;): For wireless network configuration. For some units, press LED button seven times within 10 seconds to enter AP mode.
• Follow me function (&person-symbol;): The remote measures and sends the ambient temperature to the unit every 3 minutes, optimizing temperature control at your location. Press and hold TURBO for 7 seconds to start/stop the memory feature (displays 'ON' or 'OF'). This function is not canceled by ON/OFF, mode changes, or power failure when activated.

**INTERIOR COMFORT MADE SIMPLE**

Due to updates and constantly improving performance, the information and instructions within this manual are subject to change without notice. Please visit www.mrcool.com/documentation to ensure you have the latest version of this manual.

Version Date: 08-11-22