Manuals+

Q Smart Home Lights 833385: Installation and Fitting Guide

This document provides instructions for the installation, setup, and basic operation of the Q Smart Home Lights model 833385.

Product Overview and Specifications

Model: 833385

Power Supply:
230V/50Hz~
LED Board:
1x LED-Board 24V DC/28W (not changeable)
Wireless Connectivity:
? 2.4 GHz, 10 dBm
Light Output (LED Board):
28W, 3000 lm
Power Consumption:
33W
Luminous Flux:
1150 lm
Lifespan (t):
20,000 h
Color Temperature (T_K):
2700-5000 K
Switching Cycles:
15,000 x
Features:
?️ Dimmable with remote control

Included Accessories:

Compliance Symbols: CE, ♻️ (WEEE Directive)

Image Description: A modern, circular LED ceiling light fixture with a metallic finish. Below it are a remote control with various buttons and two AAA batteries.

Installation Instructions

Step 1: Fitting (As Ceiling Light)

This step involves mounting the fixture to the ceiling.

Diagram Description: 1. Shows a terminal block with screw terminals for wire connections (labeled '0'). A finger is shown inserting a wire. 2. Illustrates attaching a mounting bracket to the ceiling using screws and possibly wall plugs. The bracket is shown with screw holes. 3. Indicates the placement of the bracket on the ceiling. 4. Shows screws and possibly drill bits for mounting. A dimension of Ø8mm is indicated, likely for the mounting holes. The final part of the diagram shows the light fixture itself, ready to be attached to the mounted bracket.
  1. Secure the mounting bracket to the ceiling using the provided screws. Ensure it is firmly attached.
  2. Prepare the electrical wiring.
  3. Attach the light fixture to the secured bracket.

Step 2: Electrical Connection

Connect the fixture to the 230 Volt/50Hz power supply.

Diagram Description: Shows a close-up of the terminal block where wires are inserted. - Label 'N' indicates the Neutral wire connection. - Label 'L' indicates the Live wire connection. - Arrows show the direction of wire insertion into the terminals. - The diagram illustrates connecting the mains supply wires (Live and Neutral) to the corresponding terminals on the fixture's internal connector block. - The connection is for a 230V/50Hz AC supply. - Symbols like 'a=N' and 'b=L' clarify which wire goes where.
  1. Ensure the power supply is switched off before making any connections.
  2. Connect the Live wire (L) to the terminal marked 'L'.
  3. Connect the Neutral wire (N) to the terminal marked 'N'.
  4. Secure the wires in the terminal block.
  5. Ensure all connections are safe and properly insulated.

Step 3: Teach Remote Control

Pair the remote control with the light fixture.

Diagram Description: Illustrates the process of pairing the remote control with the light. - The light fixture is shown with a symbol indicating a 'Q-receiver (Antenna)'. - A remote control is shown. - Instruction 9: 'Leuchte einschalten / Switch on the lamp' - shows a hand turning on a light switch. - Instruction 10: 'Bedienungsanleitung lesen / Read instruction manual' - shows the instruction manual cover. - Instruction 11: 'Q-Fernbedienung anlernen / Teach Q-remote control' - shows the remote control being used. - A note indicates to refer to the 'Q-remote control manual' for detailed instructions.
  1. Refer to the separate "Q-remote control manual" for detailed pairing instructions.
  2. Typically, this involves switching the lamp on and off in a specific sequence, or pressing buttons on the remote control while the lamp is powered.
  3. Ensure the remote control is within range of the light fixture.

Reset Procedure

Reset the lamp to its factory default settings.

Diagram Description: Illustrates a sequence of turning the light on and off to perform a factory reset. - The sequence is labeled "5x on/off". - The first step shows turning the light off for 5-10 seconds. - Subsequent steps show turning the light on for 1-2 seconds, then off, repeating this cycle four more times. - Visuals show light bulbs transitioning from off (dark) to on (lit).

To reset the lamp to factory settings:

  1. Turn the lamp OFF and leave it off for 5-10 seconds.
  2. Turn the lamp ON for 1-2 seconds.
  3. Turn the lamp OFF for 1-2 seconds.
  4. Turn the lamp ON for 1-2 seconds.
  5. Turn the lamp OFF for 1-2 seconds.
  6. Turn the lamp ON for 1-2 seconds.
  7. Turn the lamp OFF for 1-2 seconds.
  8. Turn the lamp ON for 1-2 seconds.
  9. Turn the lamp OFF for 1-2 seconds.
  10. Turn the lamp ON for 1-2 seconds.

The lamp should now be reset to its factory default state.

Declaration of Conformity

This device fulfills the fundamental requirements of Directive 2014/53/EU (Radio Equipment Directive) of the European Parliament and of the Council of the European Union, dated 16.04.2014, on items of radio equipment.

The full declaration of conformity can be accessed at the following internet address:

https://scm.paul-neuhaus.de/public/conformity/

Manufacturer:

Paul Neuhaus GmbH
Olakenweg 36
D-59457 Werl

Contact:

Telefon: +49(0)2922-9721-0
Telefax: +49(0)2922-9721-9120
E-Mail: Kundenservice@neuhaus-group.de

Models: 8414-55, Q-VITO Stainless Steel Ceiling Light LED, 8414-55 Q-VITO Stainless Steel Ceiling Light LED, Stainless Steel Ceiling Light LED, Ceiling Light LED, Light LED

File Info : application/pdf, 6 Pages, 325.44KB

PDF preview unavailable. Download the PDF instead.

074025-IM-8414-55-01

References

GPL Ghostscript 9.25

Related Documents

Preview Q Smart Home Lights Fitting Instructions and Technical Specifications
Comprehensive fitting instructions and technical details for Q Smart Home Lights, including power, brightness, color temperature, lifespan, and remote control operation. Features multilingual support for German and English.