LED Floodlight BVP151
Mounting Instructions
General Safety and Installation Precautions
- Please read this manual carefully before using the product.
- Do not switch on before complete installation.
- The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEE electrical regulations or the national requirements.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire shall be replaced.
- The luminaire is complied with IEC 60598.
- Luminaire must not be used or stored in corrosive environments where hazardous materials such as Sulphur, Chlorine, phthalates, etc., are present.
- This marking ♻️ indicates that this product should not be disposed of with other household wastes throughout the EU. Recycle it responsibly to promote the sustainable reuse of material resources.
Product Specifications
| Type | CCT (K) | Power (W) | Lumen Output (lm) | LEDs | Dimensions (mm) AxBxCxD | Projected Area (m²) | Voltage | Frequency | Surge Rating |
|---|---|---|---|---|---|---|---|---|---|
| BVP151 LED12/WW PSU 10W SWB MDU G2 GM | 3000K | 10W | 1100lm | 36 | 63.8x155x52x82.8 | 0.005 | 220-240V~ | 50/60Hz | 2KV/2KV |
| BVP151 LED12/NW PSU 10W SWB MDU G2 GM | 4000K | 10W | 1200lm | 36 | 63.8x155x52x82.8 | 0.005 | |||
| BVP151 LED12/CW PSU 10W SWB MDU G2 GM | 6500K | 10W | 1200lm | 36 | 63.8x155x52x82.8 | 0.005 | |||
| BVP151 LED24/WW PSU 20W SWB MDU G2 GM | 3000K | 20W | 2200lm | 60 | 82x172x52x100 | 0.008 | |||
| BVP151 LED24/NW PSU 20W SWB MDU G2 GM | 4000K | 20W | 2400lm | 60 | 82x172x52x100 | 0.008 | |||
| BVP151 LED24/CW PSU 20W SWB MDU G2 GM | 6500K | 20W | 2400lm | 60 | 82x172x52x100 | 0.008 | |||
| BVP151 LED36/WW PSU 30W SWB MDU G2 GM | 3000K | 30W | 3300lm | 90 | 117x220x53x145 | 0.017 | |||
| BVP151 LED36/NW PSU 30W SWB MDU G2 GM | 4000K | 30W | 3600lm | 90 | 117x220x53x145 | 0.017 | |||
| BVP151 LED36/CW PSU 30W SWB MDU G2 GM | 6500K | 30W | 3600lm | 90 | 117x220x53x145 | 0.017 | |||
| BVP151 LED60/WW PSU 50W SWB MDU G2 GM | 3000K | 50W | 5500lm | 120 | 150x263x53x185 | 0.028 | |||
| BVP151 LED60/NW PSU 50W SWB MDU G2 GM | 4000K | 50W | 6000lm | 120 | 150x263x53x185 | 0.028 | |||
| BVP151 LED60/CW PSU 50W SWB MDU G2 GM | 6500K | 50W | 6000lm | 120 | 150x263x53x185 | 0.028 | |||
| BVP151 LED84/WW PSU 70W SWB MDU G2 GM | 3000K | 70W | 7700lm | 170 | 175x293x53x215 | 0.038 | |||
| BVP151 LED84/NW PSU 70W SWB MDU G2 GM | 4000K | 70W | 8400lm | 170 | 175x293x53x215 | 0.038 | |||
| BVP151 LED84/CW PSU 70W SWB MDU G2 GM | 6500K | 70W | 8400lm | 170 | 175x293x53x215 | 0.038 |
Electrical Specifications
| Type | Run Current (A) (@230V) | Start (Inrush) Current (A) / Ipeak (A) | Start Current Duration (µs) / T (@50% of Ipeak) (µs) | Touch Current or Protective Conductor Current (mA) | Max. Luminaire on MCB 16A Type B (pcs) | Max. Luminaire on MCB 16A Type C (pcs) |
|---|---|---|---|---|---|---|
| BVP151 10W | 0.055 | 0.78 | 6.48 | <3.5 | 218 | 254 |
| BVP151 20W | 0.1 | 1.1 | 7.4 | <3.5 | 109 | 127 |
| BVP151 30W | 0.15 | 1.22 | 7.2 | <3.5 | 73 | 85 |
| BVP151 50W | 0.25 | 1.68 | 8.2 | <3.5 | 44 | 51 |
| BVP151 70W | 0.35 | 3.64 | 22.2 | <3.5 | 31 | 36 |
The leakage current (touch current or protective conductor current) is dependent upon electrical supply cables, connections, and site conditions.
Mounting and Wiring
IP65 Junction Box
Use an IP65 or higher rated junction box/connector for wiring connections. Ensure the wiring connection is not submerged in water, soil, or snow. An IP68 junction box can also be used.
The terminal block should comply with EN60998-2-1/EN60998-2-2.
The exposed wire length is 1000mm for all wattages (10W/20W/30W/50W/70W).
Mounting hole dimensions (a, b, c, d, e) are provided in a diagram, with specific values listed for different wattages:
- Dimension 'a': 4.2mm (10W, 20W), 4.5mm (30W), 6.5mm (50W, 70W)
- Dimension 'b': 4.2mm (10W, 20W), 4.5mm (30W), 6.5mm (50W, 70W)
- Dimension 'c': 79mm (10W), 97mm (20W), 133mm (30W), 173mm (50W), 203mm (70W)
- Dimension 'd': 35mm (10W), 50mm (20W), 70mm (30W), 90mm (50W), 110mm (70W)
- Dimension 'e': 45mm (10W), 60mm (20W), 85mm (30W), 110mm (50W), 130mm (70W)
Wiring connections: L (Brown wire), N (Blue wire), GND (Yellow-Green wire). Cable type: H05RN-F 3x1.0 mm² (60245IEC57).
The warranty is void if instructions are not followed. This product is not supplied with a junction box/connector.
Working Modes
Sensor Mode
The product will light up when people pass by.
- Time-Delay: Adjustable from 10 sec ± 3 sec (min) to 7 min ± 3 min (max).
- Ambient Light: Adjustable from 3-2000 LUX.
- Sensing Distance: 0-8m.
The sensor controls are labeled TIME, SENS, LUX. The detection range is illustrated, showing coverage up to 5.0m and 8.0m.
Non-Sensor Mode (Always ON)
To activate non-sensor mode:
- Turn on the light.
- After 5 seconds, quickly switch the light OFF and then ON again (two cycles).
- The product will enter non-sensor mode.
To return to sensor mode: Turn off the light and wait for more than 10 seconds.
Mechanical Installation
Fasten the bolt securely. Torque specifications:
- 10W, 20W, 30W: 3 Nm
- 50W, 70W: 8 Nm
Install the luminaire according to national regulations and ensure it is securely mounted to prevent it from falling.
Manufacturer Information
Signify Luminaires (Shanghai) Co., Ltd.
Address: 2F, Building 6, No. 1805, Huyi Highway, Malu Town, Jiading District, Shanghai, P.R. China. Postal code: 201801.
Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips N.V.
