Ikan PT4900S-PEDESTAL Quick Start Guide

Step 1

Place the Hood Attachment Frame over the Glass Holder. Position the glass against the Glass Holder, ensuring screws pass through the holes on both the Hood Attachment Frame and the Glass Holder.

Step 2

Secure the Glass Holder by fastening the knurled nuts to the screws as shown in the diagram.

Step 3

Remove the monitor mounts from the teleprompter base using the included 4mm hex key to loosen them from the 15mm rods.

Step 4

Place washers onto the screws before tightening. Washers and four additional screws are provided in a bag on the bottom foam.

Step 5

Attach the monitor mounts. Adjust the 15mm rods to accommodate the monitor, leaving approximately 1 inch of space for the teleprompter bracket. Ensure the 15mm rods pass through both sets of monitor mounts and that all screws are tightened after inserting the monitor. SAFETY NOTE: Ensure at least 2 inches of the rods remain inside the teleprompter base.

Step 6

While sliding the teleprompter bracket into the slot of the Glass Frame Holder Bracket, pull the red knob to allow the bracket to slide in fully.

Step 7

Once the bracket is in place, tighten the side screw to lock it. Double-check that all screws are tightened using the included hex keys.

Step 8

Fold the flaps of the Hood alongside the edges of the Hood Attachment Frame. The hood flaps are magnetic and will attach automatically.

Step 9

To prevent light leakage through the hood, seal both zippers down.

Step 10

Slide the Riser plate of your choice onto the Base by aligning the screws on the riser plate with the slots on the Base. Once aligned, slide the riser plate into the Base.

Step 12

Mount your tripod plate to the bottom plate using the 1/4-20 and/or 3/8-16 screws. It is recommended to attach the tripod plate to the front of the Bottom Plate for easier balancing. Once connected, mount the tripod plate to your tripod head.

Step 13

Slide the entire teleprompter system into the Bottom Plate. Balance the system by sliding it along the Bottom Plate until the center of gravity is determined.

Step 14

Once the center of gravity is determined, tighten the thumb screws to secure the base and prevent sliding.

Step 15

To secure your teleprompter system, insert the included headless screws into the threads located behind and in front of the Base.

Step 16

Insert the headless screws into the threads as pictured.

Monitor Ports

The monitor features several input and control ports:

• 3G-SDI: Serial Digital Interface Connection
• VGA: Video Graphics Array DE15 Connection
• HDMI: High-Definition Multimedia Interface Input Connection
• Power Port: 12-24v Input

Button functions include:

• HDMI: Switch HDMI input
• VGA: Switch to VGA input
• SDI: Switch to 3G-SDI input
• Flip: Toggle image flip (can be set to horizontal, vertical, or both via menu)
• Up Arrow: Toggle up to adjust setting
• Menu: Access to monitor settings
• Down Arrow: Toggle down to adjust setting

Monitor Menu Settings

The monitor offers configurable settings:

Video Config

• Contrast (White Level)
• Brightness (Black Level)
• Tint (Chroma Hue)
• Chroma (Chroma Saturation)
• Sharpness (Detail)
• RGB Setup: Manually configure RGB
• Return

System Config

• Menu Duration: Set duration of how long the menu stays on screen
• Video Ratio: Set screen aspect ratio to 16:9 or 4:3 (4:3 is native resolution; 16:9 creates black bars)
• Flip-H: Assign toggle button to flip image horizontally
• Flip-V: Assign toggle button to flip image vertically
• Reset: Factory reset
• Return

PC Setup (Only available for VGA)

• H-Position: Adjust horizontal position
• V-Position: Adjust vertical position
• Auto: Monitor automatically adjusts position
• Return

Exit

How to Set Up FLIP Button Feature

1. Press the MENU button.
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H.
4. Change FLIP-V and/or FLIP-H to "ON".
5. Exit MENU.
6. The FLIP button is now activated and can be pressed to mirror the image horizontally or vertically.
7. When FLIP-H is ON, the image flips horizontally.
8. When FLIP-V is ON, the image flips vertically.
9. If both are ON, the FLIP button toggles both horizontal and vertical flip.

E-IMAGE EP880SK Pedestal

The EP880SK pedestal is designed for professional camera support, offering stability and height adjustment.

Key specifications and components include:

Features include a pneumatic column pedestal system with adjustable air pressure, a fluid head with a 100mm ball, and double-wheel 125mm casters with adjustable cable guards.

E-IMAGE GH25 100mm Fluid Head

The GH25 is a professional fluid head designed for smooth and precise camera movements.

Features

• 7 plus 0 grades of pan & tilt drag for controlled motion.
• 15 steps of counterbalance for stable camera mounting.
• Illuminated leveling bubble for accurate setup.
• Additional standard 1/4" & 3/8" screw holes for accessories.

Specifications

E-IMAGE EP880S Pedestal

The EP880S pedestal offers robust support for professional camera setups.

Key specifications and components include:

Features include a pneumatic column pedestal system with adjustable air pressure, an ergonomic hand wheel, and double-wheel 125mm casters with adjustable cable guards.

E-IMAGE EI-7007 Super Dolly

The EI-7007 Super Dolly is designed for pedestal systems and other heavy-duty setups. Its 125mm/5-inch wheels with cable guards can be individually braked, and the movement direction can be fixed. It also folds for transport.

Features

• Pull the knob to extend the dolly, making it easy to maneuver.
• Height: 21.5cm / 8.5in; Radius: 50cm / 19.7in.
• Casters diameter: 125mm / 4.9in.
• Rubber wheels are non-marring during normal use, protecting the floor surface. Each wheel has a foot-activated brake.
• Cable guards and brakes are integrated.
• Supports up to 100kg of tripod, camera, and accessories.

E-IMAGE GB3 Pan Bar

The GB3 Pan bar is a telescopic pan bar compatible with GH08L, GH10L, GH15, and GH25 heads.

Specifications

• Length range: 405-605mm / 15.9-23.8in
• Net weight: 385g / 0.8lbs