Omada Switch | Datasheet
SG6654X
Omada Campus 48-Port Gigabit Stackable L3 Managed Switch with 6× 10G Slots
Highlights
- 48× Gigabit RJ45 ports and 6× 10 Gbps SFP+ slots
- 216 Gbps switching capacity per unit
- Physical Stacking up to 8 units for built-in redundancy and performance**
- L3 features: RIP, OSPF, ECMP, VRRP, PIM-DM, PIM-SM, and DHCP Server/Relay
- Security Strategies: ACL, Port Security, DoS Defend, 802.1X
- Highly Available with two internal fixed power supplies, VRRP, and ERPS
- Centralized cloud management via Omada SDN controller
- Standalone management via web, CLI, SNMP, and RMON
**Physical stacking up to 8 units at standalone mode and 4 units at controller mode
Omada Solution
The Omada Solution illustrates a network architecture designed for campus environments. It features Omada Access Points (Ceiling Mount AP, Wall Plate AP, Outdoor AP), Long-range Outdoor Bridges, and the Omada Switch. These devices connect to the internet and cloud, managed either by On-Premises Controllers (Hardware or Software) or through Omada Central (Cloud-Based). An Omada VPN Gateway is also part of the solution, connecting to the internet and facilitating secure access.
Product Pictures
The SG6654X switch is presented with detailed views:
- Front View: Displays 48× Gigabit RJ45 ports, 6× 10 Gbps SFP+ ports, 1× RJ45 Management Port, 1× USB Type-C Console Port, and 1× RJ45 Console Port.
- Rear View: Shows 4× Fixed Fans, Locking Strap Slots, 2× Fixed Power Supplies (with RPS - Redundant Power Supply) supporting 100-240V~50/60Hz 1.5A input, and a Physical Security Lock. It also indicates support for Physical Stacking, OSPF, VRRP, PIM, ERPS, and DHCP Server functionalities.
- Side View: Highlights the switch's rackmountable design with dimensions: 17.3 in (440 mm) width, 15.0 in (380 mm) depth, and 1.7 in (44 mm) height.
Specifications
Hardware Features & Performance
Category | Feature | Description |
---|---|---|
Interface | Ports | 48× 10/100/1000Mbps RJ45 ports, 6× 10G SFP+ Slots* |
Console Ports | 1× RJ45 + 1× USB Type C | |
Management Port | 1× RJ45 | |
General | USB Ports | 2× USB 2.0 |
Flash | 2×4 MB Nor + 8GB EMMC | |
DRAM | 4 GB DDR4 | |
Processor | Dual-core ARM @1.5GHz CPU | |
Switching Capacity | 216 Gbps | |
Forwarding Bandwidth | 108 Gbps | |
Packet Forwarding Rate | 160.7 Mpps | |
Performance | MAC Address Table | 32 K |
Packet buffer | 3MB | |
Stacking Port | 10G SFP+ slot (all uplink ports can be used as stacking ports) | |
Stacking bandwidth | Up to 120 Gbps (6 stack ports) | |
Stacking number (max) | 8 units at standalone mode and 4 units at controller mode | |
Compatible models for stacking | SG6428X, SG6428XHP, SG6654X, SG6654XHP | |
Transmission Method | Store and Forward | |
Jumbo Frame | 9 KB | |
Physical & Environment | Power Supply | 100-240 V~50/60 Hz |
Redundant Power Supply (RPS) | 2 internal fixed power supply modules | |
Max Power Consumption | 39.8 W (220 V/50 Hz) | |
Max Heat Dissipation | 135.81 BTU/hr (220 V/50 Hz) | |
Standby Power Consumption | 16.2 W (220 V/50 Hz) | |
Noise | Min: 14.8 dBA @1m 25 °C, Max: 40.7 dBA @1m 25 °C | |
Fan Quantity | 4 internal fixed fans | |
Airflow | Front-to-back | |
Surge Protection | Service port: ±6 kV in common mode; Power port: ±4 kV in differential mode; ±4 kV in common mode | |
ESD Protection | Air: ±15 kV, Contact: ±8 kV | |
MTBF | 547,093 h @ 25 °C | |
Dimensions (W x D x H) | 17.3 × 15.0 × 1.7 in (440 × 380 × 44 mm) | |
Installation | Rackmount | |
Operating Temperature | -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters; -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters; -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters | |
Storage Temperature | -40 °C to 70 °C (-40 °F to 158°F) | |
Operation Humidity | 10% to 90% RH, non-condensing | |
Storage Humidity | 5% to 90% RH, non-condensing | |
Certification | CE, FCC, RoHS |
*No more than two 10G RJ45 SFP+ modules (SM5310-T) are supported, and they can only be inserted into SFP+ slots 49&53.
Software Features
SDN Support
- Support Omada Controller
- Automatic Device Discovery
- Batch Configuration
- Batch Firmware Upgrading
Basic Function
- Auto Negotiation/Auto MDI/MDIX
- 802.3X Flow Control & Back Pressure
Physical Stacking
- Basic Feature: Max Unit Number, Topology, Hot Plug in/out
- Global Fabric Config: Unit ID Config, Stack Status/Error-Info, Automatic Stacking
L3 Features
- IP Interfaces: IPv4: Max 256, IPv6: Max 256
- Static Routing: Max 1,024, IPv6: Max 512
- Host Route Table: Max 6,100 entries
- RIP: Version v1/v2, Max 8,190; RIPng: Max 4,097
- OSPF: Version v2/v3; v2: Max 8,190, v3: Max 4,097
- VRRP: Version v2/v3, Max 64 groups
- ECMP: 256 entries, max 32 ECMP Nexhops per Destination
- Policy-based Routing (PBR)
L2 Features
- Link Aggregation: Static link aggregation, 802.3ad LACP, Up to 8 ports per group, Up to 64 LAG Groups
- Spanning Tree Protocol: 802.1d STP, 802.1w RSTP, 802.1s MSTP, Up to 16 MSTI instances, STP Security (TC Protect, BPDU Filter, BPDU Protect, Root Protect, Loop Protect)
- Loopback Detection: Port based, VLAN based
- Flow Control: 802.3x Flow Control, HOL Blocking Prevention
L2 Multicast
- IGMP Snooping: IGMP v1/v2/v3 Snooping, Fast Leave, IGMP Snooping Querier, IGMP Authentication, L2 Multicast Table (Dynamic: Max 4,093 entries, Static: Max 4,093 entries)
- IGMP Authentication
- Static Multicast IP
- Multicast VLAN Registration (MVR): Max 4,093 entries
VLAN
- VLAN Group (802.1q VLAN): Max 4K VLAN Groups
- 802.1Q Tagged VLAN
- MAC VLAN entries: 200
- Multicast VLAN
- Management VLAN
- VLAN VPN (QinQ): Max 256 entries
- GVRP
QoS
- Class of Service: 8 Queues of Priority, Port Priority, IEEE 802.1p Priority, DSCP Priority, Queue Min-Bandwidth, Schedule Mode (SP, WRR, SP+WRR)
Additional Software Features
- Intelligent Network Monitoring
- Abnormal Event Warnings
- Unified Configuration
- Reboot Schedule
- Auto-Uplink Every Port
- Fabric Port Config (Port Config, Port Status)
- Virtual MAC Config
- Static ARP: 512 static entries
- Dynamic ARP: 7,680 dynamic entries
- Proxy ARP
- DHCP Server: Max 64 IP Pools, Max 8000 Leases, Max 1,000 Manual Binding Entries
- DHCP Relay: Relayed Interface, Relayed VLAN
- IPv4/IPv6 dual stack
- IGMP: Version v1/v2/v3, Max 2048 IGMP Groups
- PIM: PIM-DM(v4), PIM-SM(v4), PIM-SSM(v4), Max 1024 Multicast Route Entries
- Supports 2,048 IGMP groups
- ERPS: Up to 16 ERPS rings
- Mirroring: Port Mirroring, CPU Mirroring, One-to-One, Many-to-One, Tx/Rx/Both
- RSPAN
- Mac Address: MAC Address Table (Static: Max 128 entries, Dynamic: Max 32k entries, Filtering: Max 128 entries)
- MLD Snooping: MLD v1/v2 Snooping, Fast Leave, MLD Snooping Querier, Static Group Config, Limited IP Multicast
- Multicast Filtering: 256 profiles and 16 entries per profile
- Protocol VLAN (IEEE 802.1v): Protocol Template 16, Protocol VLAN 12 entries
- VLAN VPN: VLAN Mapping, VLAN Replace
- Voice VLAN
- Private VLAN
- Bandwidth Control: Rate Limit, Storm Control
- User-Defined OUI
- Smoother Performance
- Action for Flows: QoS remark (802.1P Remark, DSCP Remark)
ACL
- MAC ACL: Source MAC, Destination MAC, VLAN ID, User Priority, Ether Type
- IP ACL: Source IP, Destination IP, Fragment, IP Protocol, TCP Flag, TCP/UDP Port, DSCP/IP TOS
- Combined ACL
- IPv6 ACL
- Policy: Mirroring, Redirect, Rate Limit, QoS Remark
- ACL apply to Port/VLAN
- Time-based ACL
- Templates: default (IPv4 ACL Rules: 300, MAC ACL Rules: 300, Combined ACL: 300, IPv4 Source Guard: 299); IPv4 access (IPv6 ACL Rules: 0, MAC ACL Rules: 300, Combined ACL: 500, IPv4 Source Guard: 499); IPv6 access (IPv4 ACL Rules: 0, MAC ACL Rules: 200, IPv6 ACL: 250, IPv6 Source Guard: 249); Omada (IPv4 ACL Rules: 0, MAC ACL Rules: 0, Combined ACL: 600, IPv4 Source Guard: 0)
Security
- Port Isolation
- CPU-Deffend
- Dynamic ARP Inspection (DAI)
- DoS Defend
- IP-MAC-Port Binding: 1,024 Entries (DHCP Snooping, ARP Inspection, IPv4 Source Guard)
- IPv6-MAC Port Binding: 1,024 Entries (DHCPv6 Snooping, ND Detection, ND Snooping, IPv6 Source Guard)
- DHCP Filter
- Static/Dynamic Port Security: Up to 64 MAC addresses per port
- Broadcast/Multicast/Unknown-unicast Storm Control (kbps/ratio control mode)
- 802.1X: Port base authentication, Mac base authentication, VLAN Assignment, MAB, Guest VLAN, Support RADIUS authentication and accountability
- AAA (including TACACS+)
- Secure web management through HTTPS with SSLv3/TLS 1.2
- Secure Command Line Interface (CLI) management with SSHv2
- IP/Port/MAC based access control
ISP Features
- 802.3ah Ethernet Link OAM
- L2PT (Layer 2 Protocol Tunneling)
- PPPoE ID Insertion
Management
- Web-based GUI
- Web-Based HTTP or HTTPS
- TFTP/TFTPv6
- FTP/FTPv6
- File System
- Debug
- CLI: Console, Telnet, Telnetv6
- SNMP: v1/v2c/v3, SNMP Trap, SNMP Inform, RMON (1, 2, 3, 9 groups)
- Link Layer Discovery Protocol (LLDP)
- VCT (Virtual Cable Test)
- System IP: Static IP, DHCP Client, BOOTP Client
- 802.1ab LLDP/LLDP-MED
- DHCP Auto Install
- Device Link Detect Protocol (DLDP)
- sFlow
- DDM
- Maintenance: CPU/Memory Monitor, System Log, Cable Test, Ping/Tracert, Pingv6, ICMP/ICMP v6
- Time Setting: NTP, DST
- System Tools: Dual Image, Config Restore/Backup, Firmware Upgrade, System Reboot/Reset
- User Management: User Settings, Access Level, Password Recovery Settings
- SDM Template
- IEEE 802.3az Energy Efficient Ethernet (EEE)
MIBs
- MIB II (RFC1213)
- Interface MIB (RFC2233)
- Ethernet Interface MIB (RFC1643)
- Bridge MIB (RFC1493)
- P/Q-Bridge MIB (RFC2674)
- RMON MIB (RFC2819)
- RADIUS Accounting Client MIB (RFC2620)
- RADIUS Authentication Client MIB (RFC2618)
- Remote Ping, Traceroute MIB (RFC2925)
- Support TP-Link Private MIB
Ordering Information
Host Switch
Model | Description |
---|---|
SG6654X | Omada Campus 48-Port Gigabit Stackable L3 Managed Switch with 6× 10G Slots |
SFP/SFP+ Modules
Model | Description |
---|---|
SM311LS | Gigabit SFP module, Single-mode, LC interface, Up to 20km distance |
SM311LM | Gigabit SFP module, Multi-mode, LC interface, Up to 550m distance |
SM321A | Gigabit WDM Bi-Directional SFP Module, single-mode, LC connector, TX: 1550 nm/RX: 1310 nm, 20 km |
SM321A-2 | Gigabit WDM Bi-Directional SFP Module, single-mode, LC connector, TX: 1550 nm/RX: 1310 nm, 2 km |
SM321B | Gigabit WDM Bi-Directional SFP Module, single-mode, LC connector, TX: 1310 nm/RX: 1550 nm, 20 km |
SM321B-2 | Gigabit WDM Bi-Directional SFP Module, single-mode, LC connector, TX: 1310 nm/RX: 1550 nm, 2 km |
SM5110-LR | 10GBase-LR SFP+ LC Transceiver, single-mode, LC connector, 1310nm, 10 km |
SM5110-SR | 10GBase-SR SFP+ LC Transceiver, multi-mode, LC connector, 850nm, 300 m |
RJ45 SFP/SFP+ Modules
Model | Description |
---|---|
SM331T | 1000BASE-T RJ45 SFP Module |
SM5310-T | 10GBASE-T RJ45 SFP+ Module |
MC Series Media Converter
Model | Description |
---|---|
MC210CS | Gigabit Single-Mode Media Converter, up to 20 km, chassis mountable |
MC200CM | Gigabit multi-mode SC SFP Transceiver, up to 550 m, chassis mountable |
MC200L | Gigabit SFP slot supporting mini-GBIC modules, chassis mountable |
MC1400 | 14-slot power supply chassis for TP-LINK MC Series Media Converter, 19-inch rack-mountable |
Some models featured in this guide may be unavailable in your country or region. Visit TP-Link website for local sales information: www.omadanetwokrs.com. Specifications are subject to change without notice. All the brands and product names are trademarks or registered trademarks of their respective holders. © 2025 TP-Link