May in Color Outdoor Motor Sun Shade
This document provides detailed instructions for the assembly and installation of the May in Color Outdoor Motor Sun Shade.
Assembly Instructions
Carefully unpack all components and verify that all necessary parts are included as listed in the packaging. Identify each component and refer to the provided assembly diagram or step-by-step instructions. Assemble the unit in the order specified to ensure proper alignment and fit. Use the provided tools or recommended tools for assembly. Do not use excessive force when tightening screws or bolts. If difficulties arise during assembly, consult the troubleshooting section or contact customer support.
Tools You May Need
- Screwdriver ?
- Measuring Tape ?
- Pencil ✏️
- Drill bits (Optional) ?
[Tools not included]
Package Contents
The package contains the following components:
| Size | Roller Tube Assembly | Mounting Brackets (a) | Screws (b) | Wall Anchors (c) |
|---|---|---|---|---|
| 6ft | 1 | 4 | 12 | 12 |
| 8ft | 1 | 4 | 12 | 12 |
| 10ft | 1 | 5 | 14 | 14 |
Product Assembly
Ceiling Mounting
- Step 1: Locate the drilling holes with a measuring tape or straight ruler. Mark the mounting bracket locations through the holes with a pencil. (Diagram shows ceiling with measurements indicating bracket placement, and a pencil marking holes).
- Step 2: Use the screws to anchor in the (pencil marked) bracket holes to firmly attach the mounting brackets to the surface. (Diagram shows a close-up of a mounting bracket being attached to a surface using screws and anchors, with a drill.
- Step 3: Place the top rail under the brackets and touch the plastic plug to the rail's outer ridge, then press inward and lift upward to complete the mount. (Diagram shows the top rail being inserted into the brackets, with arrows indicating the locking motion).
- Step 4: Operate the shade. (Diagram shows the shade in its operating position).
- Step 5: Tie down the cable in a true vertical or allowable position. (Diagrams show two options for tying down the control cable, with dashed lines indicating the cable path and crossed-out circles indicating incorrect tie-down points. Labels "VALANCE" and "FABRIC" are visible).
- Step 6: The assembled shade is ready for operation. (Diagram shows the fully assembled shade with its remote control).
Wall Mounting
- Step 1: Locate the drilling holes with a measuring tape or straight ruler. Mark the mounting bracket locations through the holes with a pencil. (Diagram shows a wall with measurements indicating bracket placement, and a pencil marking holes).
- Step 2: Use the screws to anchor in the (pencil marked) bracket holes to firmly attach the mounting brackets to the surface. (Diagram shows a close-up of a mounting bracket being attached to a surface using screws and anchors, with a drill).
- Step 3: Place the top rail under the brackets and touch the plastic plug to the rail's outer ridge, then press inward and lift upward to complete the mount. (Diagram shows the top rail being inserted into the brackets, with arrows indicating the locking motion).
- Step 4: Operate the shade. (Diagram shows the shade in its operating position).
- Step 5: Tie down the cable in a true vertical or allowable position. (Diagrams show two options for tying down the control cable, with dashed lines indicating the cable path and crossed-out circles indicating incorrect tie-down points. Labels "VALANCE" and "FABRIC" are visible).
- Step 6: The assembled shade is ready for operation. (Diagram shows the fully assembled shade with its remote control).
Care and Maintenance
- Please measure your window or wall before you install the shades; you can use a pencil to mark the right position before you install them.
- If the package or product comes damaged, please take photos and contact NINGBO JIAYUAN WINDOW COVERINGS CO.,LTD. They will arrange replacement or other solutions according to the situation.
- Your satisfaction is the best motivation. Please leave a review to help improve the product and service.
- To clean the shade fabric, simply rinse with water and soap and scrub with a soft brush. Remember to unplug the shade before cleaning; do not allow the motor to get wet. Note: using bleach or an abrasive cleaner will void your warranty.
- Roll the shade down to air dry. Your shade should be rolled up during high wind conditions.
Frequently Asked Questions (QA)
Q1: How to wash this roller shade?
A: Dust with a dry cloth or wipe with a damp cloth.
Q2: What if the product can't work and my return window has closed?
A: NINGBO JIAYUAN WINDOW COVERINGS CO.,LTD offers a 2-year warranty. If you come across any problems during your usage, please contact customer support.
Q3: How long will it take to use the roller shade after I install it?
A: Normally you can use it immediately once it is assembled, but please check if it is fully assembled. It might fall off if the screws are not tightened.
Thank You
Thank you for purchasing May in Color products.
Your satisfaction is the best motivation to us. Please leave us your review to help us improve our product and service. [?]
[Scan QR code to review your purchase]
[Scan QR code to contact us]
If you have any problems, please feel free to contact us.
Email address: service@heynemo.com
You get a 2-year warranty for May in Color Roller Shades.
FCC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.