IKEA TINAD Fridge/Freezer

Product Description

The appliance features a refrigerator compartment and a freezer compartment. Key components include glass shelves, bottle racks, crisper drawers, and various door balconies.

Refrigerator Compartment:

• 1 Fan
• 2 Glass shelves
• 3 Bottle rack
• 4 Crisper Cover
• 5 Crisper (vegetable components)
• 9 Control panel with LED light
• 10 Dairy balcony
• 11 Door balcony
• 12 Bottle holder
• 13 Bottle balcony

Zones within the refrigerator compartment include: Least cold zone, Intermediate temperature zone, and Coldest zone.

Freezer Compartment:

• 6 Small drawer
• 7 Big box drawer
• 8 Lower drawer

Note: Characteristics, technical data, and images may vary according to the model.

First Time Use

After installation, wait at least two hours before connecting the appliance to the power supply. The appliance will start automatically. Ideal storage temperatures are preset. Allow 4-6 hours for the correct storage temperature to be reached in a normally filled appliance.

Control Panel

The control panel features:

• A: LED light
• B: Refrigerator compartment temperature display
• C: Button for temperature regulation and Stand-by function

LEDs indicate the set temperature:

• High (least cold)
• Medium-high
• Intermediate
• Medium-low
• Low (coldest)

Functions

Fan

The fan is pre-set to ON. It can be turned on/off by pressing the light button (A) and button C simultaneously. A single flash indicates the fan is OFF; three flashes indicate it is ON. The fan is essential for proper food preservation when ambient temperature exceeds 27°C or if condensation forms on the glass shelves. Deactivating the fan optimizes energy consumption.

Stand-by

Press and hold button C for 3 seconds to deactivate the appliance. The control panel and lights will turn off. Briefly press the button again to reactivate. Note: This function does not disconnect the appliance from the power supply. Ambient temperature, door opening frequency, and appliance placement can affect internal temperatures and should be considered when setting the thermostat.

Fast Cooling Function

To quickly cool the refrigerator compartment or to prepare the freezer for a large quantity of food, activate the 'Fast Cooling' function by repeatedly pressing button C until the three icons flash green and remain lit. The function automatically turns off after 30 hours, returning the temperature to the previous setting. To avoid food waste, refer to recommended settings and storage times in the user manual.

Installation

Safety Precautions:

• Installation and handling require at least two people to prevent injury. Use protective gloves to avoid cuts.
• Installation, water supply, electrical connections, and repairs must be performed by a qualified technician.
• Keep children away from the installation site.
• Check for transport damage after unpacking. Contact the dealer or Aftersales Service for any issues.
• Keep packaging waste out of reach of children to prevent suffocation.
• Disconnect the appliance from the power supply before installation to avoid electric shock.
• Ensure the power cable is not damaged during installation to prevent fire or electric shock.
• Activate the appliance only after installation is complete.
• Be careful not to damage floors when moving the appliance. Install on a stable, level surface capable of supporting the weight.
• Ensure the appliance is not near a heat source.
• Allow at least two hours after installation before switching on to ensure the refrigerant circuit is efficient.
• Ensure the supply cord is not trapped or damaged.
• Secure the appliance according to manufacturer instructions. Do not allow contact between the appliance's rear wall (condenser coil) and gas/water pipes or electrical wires.
• Ensure adequate ventilation by leaving space on the sides and above the appliance. Maintain a 50 mm gap between the rear of the appliance and the wall to avoid hot surfaces. Reducing this gap increases energy consumption. Remove the power cord from the condenser hook during installation before connecting to power supply.

Inspection Checklist:

Follow the checklist before use. If any answer is 'No', follow the relevant action.

• Condensation tray: Check if the tube is inside the tray. If not, place the tube inside the tray.
• Door gasket seal: Ensure the gasket seals all around the door when closed. If not, refer to the AI - door alignment step.
• Collision check: Ensure no collision between parts/furniture when opening/closing the cooling door. If there is, refer to the AI - door alignment step.
• Kitchen system security: Secure the installation within any kitchen system and fix as required. If not, follow the AI for proper installation.

Note: On the rating plate, the article number is 8 digits, and the serial number is 12 digits.

When contacting the Service Provider, state the codes from the product's identification plate. Model information can be retrieved using the QR-Code on the energy label, which links to the https://eprel.ec.europa.eu database portal.

General Information

Keep drawers, baskets, and shelves in their current positions unless otherwise specified. The LED lighting system provides better illumination and lower energy consumption compared to traditional bulbs. Remove doors and lids before disposing of the appliance to prevent entrapment of children or animals. This product contains a light source of energy efficiency class G.

Technical Data

Download Full Version

For the complete user manual, visit www.ikea.com.