OYPLA Garden Wagon

Safety Information

Please ensure you read and fully understand these instructions before use.

While every attempt is made to ensure the highest degree of protection in all equipment, we cannot guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold on this condition, which no representative of the company can waive or change.

• This product is not a toy, and is only to be used for its designated purpose.
• This product is intended for outdoor use only.
• Do not carry out alterations or modifications to this product.
• Clean only with a damp cloth. Do not use strong industrial cleaning substances.
• Leaving the product outside exposed to weather, especially direct sun, rain and salt air, will speed the weathering process. This can be slowed by removing the product from these conditions, or covering it with a suitable cover.
• Do not fill the tires with too much air as this may cause for them to become damaged due to the density.
• Before using the product, make sure all the fastenings are tightly in place and that everything is in order, and checked periodically by an adult.
• The maximum weight capacity is 400kg. Do not exceed this.
• Ensure the load is evenly spread. Don't turn too quickly as this may cause the load to become unsafe and fall out.
• Don't pull the trolley off of curbs or other elevated places as this may damage the load and/or the trolley. Use a ramp where possible.
• If the product is damaged or has any defects, please contact cservice@oypla.com.
• Warning! This product contains small parts that could be a choking hazard. Keep children and pets away whilst assembling the product.

What's In The Box?

Please note that you will be referring to the below parts list during assembly. If any of the below parts are missing or damaged, please contact our dedicated team at cservice@oypla.com.

• 2pcs Platform Front/Rear Panel: Two mesh panels that form the front and rear of the wagon bed.
• 2pcs Platform Side Panel: Two mesh panels that form the sides of the wagon bed.
• 1pcs Trolley Platform: The main base frame of the wagon.
• 1pcs Handle Beam: The main horizontal bar that connects to the steering mechanism.
• 1pcs Handle Beam Axle: The axle that the handle beam pivots on.
• Rear Axle: The axle supporting the rear wheels.
• 8pcs Hitch Pin: Small pins used for securing certain components.
• 1pcs Handle Support Bolt: A bolt used to attach the handle beam.
• 8pcs Trolley Support Bolts: Bolts used to secure the platform panels to the frame.
• 1pcs Handle Beam Washer: A washer for the handle beam assembly.
• 8pcs Support Washers: Washers used with support bolts.
• 9pcs Support Nuts: Nuts used with support bolts.
• 5pcs Securing Pin: Pins used to secure axles and other components.
• 1pcs Wheel: A single pneumatic tire with a rim. (Diagram shows 4 wheels total).
• 1pcs Rotation Joint: A component likely related to the steering or handle attachment.
• 1pcs Handle: The main handle for steering and pulling the wagon.

Assembly Instructions

Please refer to the below information to help assemble your Oypla product. If you require assistance with the assembly of your Oypla product, please contact our dedicated team at cservice@oypla.com.

1. Step 1: Handle Beam Assembly

   Place the handle beam (part 1) on top of the handle beam axle (part 2), ensuring that the handle beam (part 1) is as far down as possible. This should leave a section of the handle beam axle (part 2) exposed. Slide the handle beam washer (part 3) onto the exposed section of the handle beam axle (part 2). Secure these in place with a securing pin (part 4). Please see the accompanying diagrams for visual guidance.

2. Step 2: Attaching Handle Beam to Platform

   Slide the handle beam (part 1) onto the trolley platform (part 5) so that it aligns with either group of holes in the bottom of the trolley platform (part 5). Once done, hold the handle beam (part 1) in place using a trolley support bolt (part 6) and secure this in place with a support washer (part 7) and a support nut (part 8). Repeat for the other holes. Please see the accompanying diagrams for visual guidance.

3. Step 3: Attaching Rear Axle

   Slide the rear axle (part 9) onto the other set of holes on the trolley platform (part 5). As with the handle beam, secure these in place using the trolley support bolts (part 6), support nuts (part 7), and support washers (part 8). Repeat for the other holes. Please see the accompanying diagram for visual guidance.

4. Step 4: Attaching Wheels

   Push a wheel (part 10) onto either the handle beam axle (part 2) or the rear axle (part 9). Then, slide a wheel washer (part 11) onto either axle and secure both the wheel (part 10) and the wheel washer (part 11) into place with a securing pin (part 4). Repeat this step on the opposite side and the remaining axle to complete the attachment of all wheels. Please see the accompanying diagrams for visual guidance.

5. Step 5: Attaching Side Panels

   Align the metal tube on the bottom of the platform side panel (part 12) with the corresponding metal tube on the trolley platform (part 5). Secure this in place with a hitch pin (part 13). Repeat this process on the other side of the platform side panel (part 12) to complete this side. Then, repeat this entire process on the opposite side of the trolley platform (part 5) to complete both sides. Please see the accompanying diagram for guidance.

6. Step 6: Attaching Front Panel

   Align the metal tube on the bottom of the trolley platform front panel (part 14) with the metal tube on the trolley platform (part 5). Secure this in place with a hitch pin (part 13). Repeat this on the other side of the platform front panel (part 14) to complete this side. Then, repeat this process on the opposite side of the platform (part 5) to complete both sides. Please see the accompanying diagram for guidance.

7. Step 7: Attaching Handle

   Slide the handle (part 15) into the handle rotation pod (part 16), making sure the holes in both parts are aligned. After this, push the handle support bolt (part 17) through both parts, holding them into place. Secure these with a support nut (part 7) and a support washer (part 8).

Final Checks and Usage Notes

Once completed, ensure that all the support nuts (part 8) are tightened so the parts are secure and won't fall off over time. Ensure that the securing pins (part 4) are all bent to prevent the wheels from falling off when using the Heavy Duty Garden Trolley.

Make sure to pump the wheels (part 10) up before use. This will help prevent the wheels from wearing out at a faster rate when transporting heavy loads in the Heavy Duty Garden Trolley. Do not overfill the wheels, as this may cause them to become too dense and more likely to burst.

Support and Environmental Information

Have a Question About Your Purchase?

Our dedicated customer services team are happy to help. Contact them via:

• Telephone: 020 3600 22 55
• Email: cservice@oypla.com
• Live Chat: www.oypla.com

Consider the Environment!

By recycling the cardboard box in which this product was packed, you contribute towards helping the environment. If you see a recycling logo such as the one below on the packaging, it can be recycled. If a recycling logo is not present, please check with your local authority before recycling.

♻️ [Recycling Symbol] ♻️ [Recycling Symbol] ♻️ [Recycle Me Symbol]

PLEASE RETAIN A COPY OF THESE INSTRUCTIONS FOR FUTURE CONSULTATION

An Official Oypla Branded Product

Imported by Oypla.com LLP, Uxbridge, UB8 2FX