Caséta Wireless Quick-Start Guide

In-Wall Fan Control

Welcome and thank you for purchasing a Caséta Wireless in-wall fan control. To control your ceiling fan from an app or remote, you need to replace an existing switch with a Caséta Wireless in-wall fan control. Please read this quick-start guide and watch the installation video at www.casetawireless.com/support. Enjoy the convenience of Caséta Wireless!

Double Your Warranty: Share your feedback on Caséta Wireless controls at www.casetawireless.com/register to extend your warranty by one year.

Contents Supplied

• In-wall fan control (PD-FSQN)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Installing Your Fan Control

Installation for Ceiling Fans with One Wall Switch (Single Pole)

This guide covers single-pole installations. For 3-way switch applications, visit www.casetawireless.com/3way for instructions and videos.

WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at the circuit breaker or fuse before installing.

Step 1: Install the Fan

Install the fan according to the manufacturer's instructions and ensure proper operation.

Step 2: Set Fan Speed

Use the fan's pull chain to set the fan speed to the highest setting.

Step 3: Turn Off Power

Turn off power at the circuit breaker or fuse.

Step 4: Remove Existing Switch

Remove the wallplate and the existing switch from the wall. Tag the load wire. Disconnect all wires from the switch.

[Diagram: Existing switch wiring with wires labeled Ground, Line/Hot, and Load. The load wire is indicated for tagging.]

*If your switch has more than 3 wires, consult the 3-way installation video at www.casetawireless.com/3way.

Step 5: Remove Side Sections (If Necessary)

For multi-gang installations, remove side sections of the control as needed to fit the box. Controls at the ends of a gang require only inner side sections removed. Controls in the middle require all side sections removed.

[Diagram: Illustrates which side sections to remove for controls in single-gang, two-gang (end), and two-gang (middle) installations.]

Step 6: Connect the Fan Control

1. Connect the bare copper or green ground wire from the wallbox to the green wire on the fan control using a wire connector.
2. Wrap the line/hot wire around the appropriate screw terminal on the fan control and tighten securely (5 in-lb / 0.55 N•m).
3. Connect the neutral wire from the wallbox to the white wire on the fan control using a wire connector.
4. Connect the load wire from the wallbox to the yellow wire on the fan control using a wire connector.

[Diagram: Shows the fan control with terminals labeled for Ground (green wire), Line/Hot (terminal screw), Neutral (white wire), and Load (yellow wire), illustrating the connections.]

Step 7: Mount the Fan Control

Secure the fan control in the wallbox using the provided screws.

Step 8: Attach the Wallplate

Attach the adapter plate to the fan control using the provided screws, then snap the wallplate into place. Ensure the wallplate has the correct number of openings for all installed devices.

Step 9: Turn On Power

Turn the power back on at the circuit breaker.

Using Your Caséta Wireless Kit

(Sold Separately)

With a smartphone or tablet (Bridge required, sold separately)

Control your fan from a smartphone or tablet using the Lutron Smart Bridge (sold separately). If using with a third-party bridge, follow that manufacturer's setup instructions.

Step 1: Download and Launch the Lutron App

Search for "Lutron Caseta" in your app store and download the Lutron app. Launch the app.

[Icons: App Store, Google Play. Logo: Lutron.]

Step 2: Connect to the Fan Control

Press and hold the "Off" button on the in-wall fan control. The app will guide you through the remaining setup steps.

[Diagram: In-wall fan control with the 'Off' button highlighted.]

Step 3: Complete Setup in App

Follow the on-screen instructions in the Lutron app to complete the setup process.

[Diagram: Lutron Smart Bridge and Lutron app interface.]

Without a Smartphone or Tablet (Bridge Not Required)

Pairing Fan Control and Pico Remote

1. Initiate Pairing on Fan Control: Press and hold the "Off" button on the in-wall fan control for 6 seconds until its LEDs start blinking.

[Diagram: In-wall fan control with 'Off' button pressed, indicating LEDs blinking.]

2. Initiate Pairing on Pico Remote: Press and hold the "Off" button on the Pico remote control for 6 seconds until its LEDs flash 3 times.

[Diagram: Pico remote control with 'Off' button pressed, indicating LEDs flashing.]

Repeat these steps to pair additional Pico remote controls.

Changing the Favorite Fan Speed Setting

The "Favorite" button on the Pico remote or fan control recalls a preset fan speed. The default is Medium, but you can set your preferred speed.

1. Set Desired Speed: Adjust the fan speed using the fan control or remote to your preferred setting.

2. Save Favorite Speed: Press and hold the "Favorite" button on either the remote or the fan control for 6 seconds until the LEDs blink twice. The new favorite speed is now saved.

[Diagram: In-wall fan control or Pico remote with the 'Favorite' button pressed, indicating LEDs blinking twice.]

Using Your Controls

In-Wall Fan Control Buttons

• On: Turns the fan on.
• Off: Turns the fan off.
• Slower: Decreases fan speed.
• Faster: Increases fan speed.
• Favorite: Recalls the saved favorite fan speed.
• FASS (Front Accessible Service Switch): A safety switch that disconnects power to the fan control.

Pico Remote Control Buttons

• On: Turns the fan on.
• Off: Turns the fan off.
• Slower: Decreases fan speed.
• Faster: Increases fan speed.
• Favorite: Recalls the saved favorite fan speed.

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).
• Use only with permanently installed paddle-type ceiling fans (permanent split-capacitor).
• Ensure the fan's pull chain is set to the highest speed setting before operation.
• Do not use with shaded-pole motors (e.g., bath exhaust fans).
• Do not use with fans that have integrated speed controls, unless the integrated control is removed.
• Do not connect to other motor-operated appliances or lighting loads.
• Do not use to control DC motor fans.

Troubleshooting

Symptom: Fan does not turn ON and no indicator lights turn ON.

• Ensure Front Accessible Service Switch (FASS) is fully pushed in to the ON position.
• Ensure the fan pull chain is set to the highest possible setting.
• Check wiring: Neutral wire may not be connected.
• Check circuit breaker or fuse: Ensure it is ON or replace fuse. Contact Lutron Customer Assistance or a licensed electrician if the issue persists.
• Wiring may be reversed: Check Load and Line wires against wiring diagram in Step 6.

Symptom: Fan does not work.

• Fan direction switch is between forward and reverse. Set switch to the desired position.

Symptom: Fan vibrates or wobbles.

• Fan direction switch is between forward and reverse. Set switch to the desired position.
• Fan blades may need balancing. Consult the fan manufacturer's installation guide for balancing instructions.

Symptom: Fan speed is too slow.

• Set the fan pull chain speed to high.

For additional troubleshooting suggestions, visit www.casetawireless.com/support.

Device Ratings

Codes: Install in accordance with all national and local electrical codes.

Grounding: When no "grounding means" exist in the wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove the green wire before screwing the control into the wallbox.

FCC/IC Information: This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Warranty: For warranty information, please visit www.casetawireless.com/warranty.

Trademarks: Lutron, Caséta, and Pico are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. FASS and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Google and the Google logo are registered trademarks of Google Inc., used with permission. Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

©2018 Lutron Electronics Co., Inc.

P/N 0301907 REV A

Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.