Emaux Water Technology | Emaux Pool and Spa Equipment
Instruction Manual for Emaux models including: GLOW LED Strip Light, Strip Light, GLOW LED Light, Light, GLOW LED
คู่มือ - POOL&SPA พูลแอนด์สปา
Manuals - POOL&SPA พูลแอนด์สปา
File Info : application/pdf, 5 Pages, 916.65KB
DocumentDocumentGLOW+LED STRIP Installation and Operation Manual EMAUX WATER TECHNOLOGY CO., LTD STRIVE FOR CLEAR WATER www.emauxgroup.com USER MANUAL GLOW+LED STRIP Installation and Operation Manual PAGE 16.5mm TABLE OF CONTENT 2 .... 1. PRODUCT INTRODUCTION 2 .... 2. SPECIFICATION 2.1 ELECTRICAL 2.2 DIMENSIONS (mm) 2.3 WIRING CONNECTOR TYPE AND PART NUMBER 2.4 POWER SUPPLY AND DIMMER 3 .... 3. DESIGN EXAMPLE 5 .... 4. MOUNTING 7 .... 5. ELECTRICAL INSTALLATION 8 .... 6. HOW TO USE GLDIYSC TO CUT THE STRIP AND END CAP ASSEMBLE P1 CONTENT 1. PRODUCT INTRODUCTION The underwater LED strip is designed for to latest waterproof technologies in IP68. It is an extendable and top view bendable LED light strip tube with a 120-degree beam angle and flat rectangular emission for creating underwater profile lighting. It can be controlled by a manual or wireless remote dimmer for lighting effect tuning. The LED strip includes a range of white CCT from 2700K/3000K/3500K/4000K/4500K/5000K/5700K/6500K. To provide a long-life span, reinforced PVC material can resist the harm from UV, saltwater, flame solvents, and dirt, etc. There are seven type of wiring connectors are providing mounting flexibility for layout connections. 2. SPECIFICATION 2.1 ELECTRICAL Operation Voltage Range: DC24V Max Power Rating/meter: 10W Bean angle: Top view 120 degree 2.2 DIMENSIONS (mm) 16.5mm 2.3 WIRING CONNECTOR TYPE AND PART NUMBER CODE 9042915 9042901 9042903 9042905 9042907 9042909 9042911 9042913 Model GL10 GL10SR GL10SL GL10LR GL10SD GL10BD GL10SB GL10BB Description LED strip max 20m length Power connector side right Power connector side left Power connector side both Power connector side direct Power connector side both direct Power connector side bottom Power connector side both bottom PRODUCT INTRODUCTION P2 GL10SR GL10SD GL10LR GL10SL GL10BD GL10SB GL10BB Code example: 9042915 (length 5 meter, CCT 3000K) + 9042901 = 5m LED strip, color temp 3000K with power connector side right. 2.4 POWER SUPPLY AND DIMMER 24V DC power supply provides LED strip power source and dimmer with remote control to adjust the brightness of the strip. Code E042901 106328534 106328535 Mode Description Dimmer Controller Power Supply HLG-240H-24 Power Supply HLG-120H-24 LED Dimmer with remote 24V, 240W, 100-240V AC 50/60Hz input voltage, IP67 24V, 120W, 100-240V AC 50/60Hz input voltage, IP67 Dimmer with Remote Handset Not in scale 3. DESIGN EXAMPLE Design a regular shape 10x20m rectangle pool in 3000K color temperature. 10m 3m 7m 24Vdc 5A power suppler 10m 20m 20m Order details for side power connection cable Code Description length(m) Quantity 9042915 + 9042901 GL10, 10m, color temp 3000K, GL10SR connector side right 10 2 9042915 + 9042901 GL10, 3m, color temp 3000K, GL10SR connector side right 3 1 9042915 + 9042901 GL10, 7m, color temp 3000K, GL10SR connector side right 7 1 9042915 +9042903 GL10, 10m, color temp 3000K, GL10SL connector side left 10 1 9042915 + 9042905 GL10, 20m, color temp 3000, GL10LR, connector side both 20 1 105328534 24V 5A power supply 6 To configure the connector orientation for better installation convenience, change the connector model to GL10BD for both side straight connector and GL10SD for single end straight connector. GL10BD GL10SD P3 DESIGN EXAMPLE DESIGN EXAMPLE P4 Code Description length(m) Quantity 9042915 + 9042909 10m, color temp 3000K, power connector both side direct 10 3 9042915 + 9042907 3m, color temp 3000K, power connector side direct 3 1 9042915 + 9042907 7m, color temp 3000K, power connector side direct 7 1 9042915 + 9042909 10m, color temp 3000K, power connector both side direct 20 1 105328534 24V 5A power supply 6 4. MOUNTING 1.Installing the Glow+ LED stripe required at least 2 people. Make sure the bending radius is not exceeded while installation. Maximum horizontal force not exceed 10KG The maximum horizontal force 5-10KG P5 MOUNTING 2. Mounting clip There are 3 different length of plastic mounting accessories to fit into the mounting and one stainless steel for corner mounting reinforcement. Code 106090026 106090027 106090028 106090029 Mode GLPMC GLPMC1M GLSMC GLDIYSC Description Plastic Mounting Clips Transparent 35mm Plastic Mounting Channel Transparent 1m Stainless steel Mounting Clip 5cm DIY End Connector Kit GLPMC GLSMC GLDIYSC Good mounting example >10mm >10mm Bad mounting example Installation direction Installation direction Installation direction >10mm keep 10mm in natural loose Pulling the wire is not allowed MOUNTING P6 Bending: >100mm Do not bend against light terminals. >100mm Mount the cable junction in waterproof junction box when apply to outdoor mounting. Waterproof Connector -V(Black) -V(Red) 5. ELECTRICAL INSTALLATION The system operation is 24Vdc only and current rating is 5A per 10 m strips. Therefore, a 120W minimum power supply is required to turn on the light in full brightness. Rated power LED Strip length 120W 9.5m 240W 19m Locate the power supply nearby the LED strip and connect the terminal wiring. The recommended distance is as below table. Watts of light 120W 18AWG 0.82mm² 2m 17AWG 1.04mm² 2.5m 16AWG 1.38mm² 3m 14AWG 2.07mm² 4m 12AWG 3.29mm² 8m 1.Connect the Red wiring of LED strip to Red wire of Power Supply. 10AWG 5.62mm² 12m AC Mains Waterproof Connector 24VDC wiring diagram GLOW+LED STRIP P7 ELECTRICAL INSTALLATION Black-GNG Red-24V 2.Wiring diagram with dimmer VV+ + - -V(Black) 24V Power Supply +V(Red) Connect to LED STRIP Dimmer wiring diagram waterproof connector AC Mains GLOW+ LED STRIP 6. HOW TO USE GLDIYSC TO CUT THE STRIP AND END CAP ASSEMBLE Cutting Mark Anti-skidding Aluminum Rubber gasket clip mounting piece Blank end Screw GLCUTTER If it is necessary to cut the LED strip to fit into the layout, use the GLCUTTER to cut the length where marked for the "Dotted Line" or "Scissor Mark". The cut section must have the appropriate IP rated cap flex accessory to maintain water proof IP ratings. Follow the steps below for end cap assemble after cutting. Step 1 Step2 Step3 Step4 Step5 finished assemblyview Step 1 - Place the anti-skidding clip on the very end of the tubing with the 2 tiny tabs that are pointing inwards still touching the end of the material and crimp in place. Step 2 - Line up the aluminum mounting piece so the screw hole face the plug and slide on over the antiskidding clip. Step 3 - Apply 100% clear silicone onto the end face of led neon flex Step 4 - Place the rubber gasket squarely onto the end face of led neon flex. Step 5 - Screw the blank end to the aluminum mounting piece. Code 106090030 Model GLCUTTER Description LED Neon Cutter HOW TO USE GLDIYSC TO CUT THE STRIP AND END CAP ASSEMBLE P8