DEWERT OKIN HE200 System & RF-WW-BEST Quick Reference Guide

System Overview

⚠️ Electrical components should be connected or disconnected only when the power cord is unplugged.

ℹ️ There is a delay after the supply voltage is applied before the device actually turns on. Wait at least 7 seconds before commissioning.

Connectable Components

Diagram showing the DEWERT OKIN HE200 System overview. It illustrates the central HE200 Control Unit connected via cables to components such as DELTADRIVE DS2/DZ actuators, a massage motor, and optional accessories like the RF-WW-BEST transmitter, power supplies, and USB devices. Numbered callouts identify each component.

• 1. HE200 Control Unit
• 2. RF-WW-BEST 2
• 3. RF-WW-BEST 1 (with light button)
• 4. DELTADRIVE DS2
• 5. DELTADRIVE DZ
• 6. Massage motor
• 7. POWER SUPPLY SP-A2
• 8. Connection cable
• 9. Power cord US Version
• 10. Optional: POWER SUPPLY SP-B2
• 11. Optional: Bluetooth® Receiver
• 12. Optional: USB Charger
• 13. Optional: USB Socket
• 14. Optional: Junction cable
• 15. Optional: Synchronous cable
• 16. Optional: LED-Set-3 with Power Box

HE200 Control Unit

Diagram of the DEWERT OKIN HE200 Control Unit. It shows the unit's casing with labeled ports and buttons: Power LED, Multifunction port, Reset/Pairing button, Pairing LED, and ports for optional drives. Numbered labels indicate specific connection points and functions.

Connections and Functions

• 1. Massage motor: foot end
• 2. Massage motor: head end
• 3. Multifunctions port for optional accessory
• 4. Reset button / Pairing button
• 5. Pairing LED
• 6. Power LED
• 7. Port for optional drives with direct circuit

Technical Data

RF-WW-BEST Transmitter

Diagram of the DEWERT OKIN RF-WW-BEST transmitter. The handheld remote is shown with numbered buttons corresponding to functions like drive control (up/down), memory positions (CUST 1, CUST 2), programming, massage intensity adjustment, and massage on/off. The 'POSITION', 'HEAD', 'FOOT', 'MASSAGE' labels are also visible.

Button Functions

• 1. Drive M1 up (Head)
• 2. Drive M1 down (Head)
• 3. Drive M2 up (Foot)
• 4. Drive M2 down (Foot)
• 5. Light on/off (only RF-WW-Best 1)
• 6. Memory position 1 (CUST 1)
• 7. Memory position 2 (CUST 2)
• 8. Programming button
• 9. Reset M1 + M2 up
• 10. Massage off
• 11. Massage intensity + (Head)
• 12. Massage intensity - (Head)
• 13. Massage intensity + (Foot)
• 14. Massage intensity - (Foot)
• 15. Massage on/off

Programming the RF-WW-BEST Transmitter

To put the handset into operation and establish radio communications with the HE200 control unit, follow these steps:

1. Press the Reset / Pairing button 4 on the control unit 2 times in quick succession. The Pairing LED will illuminate, and the HE200 control unit enters learning mode for approximately 10 seconds.
2. Press buttons 1 and 9 on the RF-WW-BEST transmitter simultaneously and hold them until the Pairing LED extinguishes (this programmable process takes about 10 seconds). The learning mode is now complete.

Adjusting the Intensity of the Massage

To turn the massage (head and foot end) on or off, press button 15 on the RF-WW-BEST hand-held remote control.

If the massage function is turned off, it can be turned on using buttons 11 or 13 (+). If the massage function is turned on, it can be turned off, starting from the lowest intensity, using buttons 12 or 14 (-).

The massage intensity is changed through 3 steps each time one of the buttons 11, 12, 13, or 14 is pressed.

Perform a Reference Drive

The HE200 control unit features a position feedback system that requires a one-time referencing procedure for optimal function. Actuate the Reset / Pairing button 4 until all drives travel back to their end positions. The system is then ready for operation.

FCC ID: O3YRF139C1HS31
IC: 10744A-RF139C1HS31

Saving Memory Positions

You can save 2 different memory positions on buttons "CUST 1" (button 6) and "CUST 2" (button 7) as follows:

• Move to the desired position using buttons 1 to 4.
• Press button 8 (SET) for 1 second. The massage function and the optional light will turn on for approximately 1 second.
• Within 3 seconds, press button 6 (CUST 1) or 7 (CUST 2) to save the position, massage function, and optional light. The light will turn on for approximately 1 second.

The desired position is now saved on buttons 6 or 7. You can overwrite a saved memory position at any time by repeating this process.

Switching to Automatic Moving and Factory Setting

Using the buttons "CUST 1" (button 6), "CUST 2" (button 7), and "FLAT" (button 9), you can move to various saved positions by pressing them briefly (press and release). The button does not need to be held down.

Activation

• Press buttons 11 and 13 simultaneously. The massage function and the optional light turn on for approximately 1 second.
• Briefly press button 6 (CUST 1), button 7 (CUST 2), or button 9 (FLAT). The drives will move automatically to the desired position.

Deactivation (Factory Setting)

• Press buttons 8 (SET) and 9 (FLAT) simultaneously. The massage function and the optional light turn on for approximately 1 second.

Synchronizing Two HE200 Systems

⚠️ Electrical components should be connected or disconnected only when the power cord is unplugged.

When two HE200 systems are used together, they can be connected using a synchronous cable in the multifunction port.

• Use the Reset/Pairing button 4 on the HE200 control unit to move both HE200 systems to their end positions (the lower limit positions for the drives).
• Disconnect the power plug on both HE200 systems from the power socket.
• Connect both HE200 systems by connecting the proper synchronous cable into the multifunction port.
• Insert the power plug on both HE200 systems into the power socket. Synchronous operations are possible as soon as both systems are connected to the main power.
• Both programmed handsets can be used to move the HE200 systems.

Cleaning and Care

The system was designed to be easy to clean.

• Be sure to unplug the power cord on the power supply before cleaning.
• Clean the system using a dry cloth.
• Be sure that you do not damage the connecting cables during cleaning.

Disposal

The system consists of electronic components, cables, and metal and plastic parts. Observe all corresponding national and regional environmental regulations when disposing of the system. The disposal of the end product is regulated in Germany by Elektro-G, internationally by the EU Directive 2011/65/EC (RoHS), or by any applicable national laws and regulations. (The end product is not regulated by the EU Directive 2012/19/EC (WEEE).)

The system should not be disposed of with normal household waste! [disposal icon]

FCC WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

IC WARNING

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:

• (1) This device may not cause interference; and
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.