Honeywell SRX Series Wireless Headset User Guide

Installing the Stability Strap

1. Step 1

   Prepare to attach the stability strap. One hand holds the headset band, while another hand holds a strap attachment. An arrow indicates the attachment should be inserted into a circular opening on the headset band.

   [Diagram: Hand holding headset band and strap attachment, with an arrow pointing attachment to opening.]

2. Step 2

   Secure the strap component to the headset band. A close-up view shows a hand fastening the strap.

   [Diagram: Close-up of hand attaching strap component to headset band.]

3. Step 3

   The stability strap is now installed on the headset and ready for use on a user's head.

   [Diagram: Completed stability strap installation on a user's head.]

Starting a Shift - Wireless Headset

Follow these steps to start a shift using your Honeywell wireless headset.

1. Step 6: Select Device

   Choose your device from the charging or docking station. An icon featuring a play/pause symbol indicates the active device.

   [Diagram: Device selection from a station, highlighting a play/pause icon.]

2. Step 7: Power On SRX Device

   Press and hold the power button on the SRX2 (or SRX device). The indicator light should turn solid green.

   [Diagram: Finger pressing power button on SRX2 device, showing 'solid green' indicator.]

3. Step 8: Connect Headset to Device

   For Personal Devices: Touch the electronic module of the wireless headset to the mobile device at the designated symbol (likely NFC or pairing indicator).

   For Shared Devices: First, touch the headset headband to the device at the symbol. Then, touch the electronic module to the device at the symbol.

   [Diagram: Wireless headset being touched to a mobile device at a symbol. For shared devices, shows headband then module connection.]

4. Step 9: Position Headset and Microphone

   Put on the headset and adjust the microphone. Position the microphone approximately 1 inch (2 cm) from the corner of your mouth for optimal voice capture.

   [Diagram: Headset being worn, with microphone positioned near the corner of the mouth.]

Ending a Shift - Wireless Headset

Follow these steps to properly end your shift and store your Honeywell wireless headset.

1. Step 1: Power Off Device

   Press and hold the Play/Pause button on the device until the LED indicator rotates red, indicating it is powered off.

   [Diagram: Device with Play/Pause button highlighted, showing press-and-hold action for power off.]

2. Step 2: Slide Device Out of Holster

   Remove the device from its holster. For A730 models, pull the device away, sliding it along the clip. For A710 or A720 models, open the Velcro and slide the device out.

   [Diagram: Device being removed from holster, showing two methods for A730 and A710/A720.]

3. Step 3: Insert into Slot

   Insert the device into its designated slot. Ensure the button controls face outwards and the Operator button is on top.

   [Diagram: Device being inserted into a slot with specific orientation requirements.]

4. Step 4: Power Off Headset

   Power off the wireless headset.

   [Diagram: Headset with power off action indicated.]

5. Step 5: Remove Battery

   To remove the battery, squeeze the battery release buttons on the sides.

   [Diagram: Battery removal showing squeeze action on release buttons.]

6. Step 6: Place in Charger

   Place the device or headset components into the appropriate charging unit.

   [Diagram: Devices/headsets being placed into a multi-bay charger.]

7. Step 7: Remove Belt

   If applicable, remove the belt by releasing the buckle.

   [Diagram: Belt buckle release mechanism.]

Charging the Headset Battery

Instructions for charging the Honeywell SRX series headset battery.

1. Step 1

   Locate the relevant buttons on the headset, indicated by circles.

   [Diagram: Headset with specific buttons highlighted.]

2. Step 2

   Arrows indicate the correct orientation for inserting the headset or battery into the charger.

   [Diagram: Arrows showing insertion into charger.]

3. Step 3

   Connect the headset to the charging unit.

   [Diagram: Headset connected to charger.]

4. Step 4

   Place the battery into the charger. Observe indicator lights (green, yellow, red) which may show charging status.

   [Diagram: Battery in charger with indicator lights.]

5. Step 5

   Charging typically takes less than 4 hours (<4h). Once charged, the battery can be recycled if necessary.

   [Diagram: Charging time indicator and recycling symbol.]

Sharing the Headset

Guidelines for sharing the Honeywell SRX series headset.

1. Step 1

   Attach a strap to the headset.

   [Diagram: Strap being attached to headset.]

2. Step 2

   Connect the headset to a mobile device.

   [Diagram: Headset connected to a mobile device.]

3. Step 3

   Adjust the headset for a comfortable fit.

   [Diagram: Headset being adjusted on a user's head.]

4. Step 4

   Ensure the headset is properly connected to the device.

   [Diagram: Close-up of headset connection to device.]

5. Step 5

   Store the headset in its designated storage unit.

   [Diagram: Headset being placed into a storage unit.]

6. Step 6

   A user is shown wearing and operating the headset.

   [Diagram: Person using the headset.]