Playzoom Walkie Talkies

Belt Clip Attachment

1. To remove the belt clip, press the tab at the top of the clip and slide upward.
2. To reattach, slide the clip piece down with the clip facing inward until you hear a click.

Battery Installation

1. Press down on the back panel of the unit and slide the battery cover off. You may need to remove the belt clip for easier access.
2. Insert 4 AAA Batteries (not included).
3. Replace the cover.

On / Off Button

Press and hold the power button (right of the LCD screen) for 3 seconds to power the device on or off. A beep will indicate operation.

Receive / Transmit

To transmit, press and hold the TALK button while talking into the device at a close range. Release the button to finish talking. When the button is released, your walkie-talkie can receive transmissions.

Note: Walkie-talkies must be set to the same channel and CTCSS code.

Release the TALK button when you're finished talking to receive a response.

How to Change Channels

• Press the MENU button once; the current channel number will flash on the LCD screen.
• Press the up and down buttons to change the channel.
• Press the TALK button to confirm and return to Standby mode.

Note: If no button is pressed, the device will return to Standby Mode.

CTCSS (Continuous Tone-Coded Squelch System)

These devices have an "8/20/22" channel system, allowing you to find a free channel if someone in your vicinity is using one and you wish to avoid interference.

Your devices also have sub-channels called CTCSS. Using this transmits one of 99 low-frequency tones (67-250 Hz) along with your voice signal.

Note: This feature does not impact operation or quality. To disable, select code "0F" in the menu. Press the TALK button to confirm.

Change the CTCSS Code

• Press the MENU button twice; the current CTCSS code will flash on the LCD screen.
• Press the up and down buttons to change the code.
• Press the TALK button to confirm.

VOX Selection

These devices are capable of voice-activated (VOX) control. This means the walkie-talkie will transmit any sound it picks up without pressing the TALK button. It is not recommended that VOX mode be used in a noisy or windy environment.

Note: Walkie-talkies must be set to the same channel and CTCSS code.

• VOX Mode is overridden when you press the TALK button.
• Press the Menu button 3 times and the current VOX setting will flash on the screen with an icon.
• Press the up button to set VOX intensity between 1 and 3. The higher the number, the more sensitive the device.
• Press the down button until you see "0F" to turn off VOX Mode.
• Press the TALK button to confirm.

Customer Service

For customer service, email: support@playzoom.com

Disclaimer and Limitation of Liability

Playzoom and its suppliers assume no responsibility for any damage or loss resulting from the use of this Quick Start Guide. Playzoom and its suppliers assume no responsibility for any loss or claims to third parties that may arise through the use of this product. Playzoom and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs.

Company: American Exchange Group

Important Note

Creating and developing STEM Learning products is accompanied by a responsibility that Playzoom takes very seriously. Playzoom makes every effort to ensure the accuracy of the information which forms the value of its products. However, errors sometimes can occur. Playzoom stands behind its products and encourages customers to contact Customer Service with any concerns.

FCC Compliance

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2ARUI-WT388US

Safety Warning

WARNING: All packaging materials such as tape, plastic sheets, and tags are not part of this toy, and should be discarded for your child's safety.