Congratulations

Dear Customer:

Welcome to the Euhomy family. Thank you for purchasing one of our products. Our goal is to provide you with superior service. If there is anything missing from or wrong with your order, or if you have any questions about using our ice maker, PLEASE contact us.

✉️ Email: support@euhomy.com f Facebook: @Euhomy.Official

The Euhomy team is available 24/7 to address your questions, comments, and concerns. Your satisfaction is our ultimate goal. We want to make everything right so you'll share your positive experience with other shoppers on Amazon.

If you experience any problems, please send an email to support@euhomy.com.

Our mission:

• To be the most trusted appliance brand.
• To create practical, compact appliances that better your life.

Be sure to register at www.euhomy.com/register for updates, warranty, and other relevant information.

Q&A

Contents

• Safety Precautions (02-03)
• Operation & Installation (04-07)
• Tips & Maintenance (08)
• Specifications (09)
• Warranty (10)
• Troubleshooting (support@euhomy.com) (11)

Safety Precautions

IMPORTANT SAFETY TIPS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance:

• Do not operate this or any other appliance with a damaged cord. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to prevent hazards.
• This ice maker must be positioned so that the plug is accessible. Connect to properly polarized outlets only. No other appliances should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle.
• Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep the cord away from traffic areas. Do not submerge the cord or the appliance in water.
• We do not recommend the use of an extension cord, which may overheat and become a fire hazard. If you must use an extension cord, use No. 14 AWG minimum size, rated no less than 1875 W.
• Unplug the ice maker before cleaning, maintaining, or repairing it.
• Exercise caution and use reasonable supervision when the appliance is used near children.
• Do not use your ice maker outdoors. Place the ice maker out of direct sunlight. Be sure to leave at least 6 inches of space between the back of your unit and the wall. Keep a minimum distance of 6 inches on each side of your unit free.
• Do not try to make ice cubes with liquids other than water.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
• Do not tip over the ice maker or turn it upside down.
• If the ice maker is brought in from outside in a cold season or climate, give it a few hours to warm up to room temperature before plugging it in.

Risk of Fire or Explosion: Flammable Refrigerant Used!

• Do not use mechanical devices to defrost the ice maker.
• Do not puncture the refrigerant tubing.
• Appliance is to be repaired only by trained service personnel.
• Consult the repair manual/owner's guide before attempting to install or service this product. All safety precautions must be followed.
• Dispose of this appliance in accordance with federal or local regulations.
• Follow handling instructions carefully.
• The ice maker should be installed in accordance with the safety standard for refrigeration systems, ASHRAE 15.
• The ice maker shall not be installed in corridors of public buildings.
• If the unit needs maintenance or repairs, replace failed parts only with like parts. Service shall be done only by factory-authorized service personnel to minimize the risk of possible ignition due to incorrect parts or improper service.

Note:

The wires in this electrical cord are color-coded as follows: Green or green with stripe

To prevent a hazard resulting from instability of the appliance, it must be placed on a flat, level surface.

Operation & Installation

ASSEMBLY AND PARTS

1. Water tank cover
2. Unit top cover
3. Water separator pipe
4. Evaporator
5. Ice basket
6. Ice scoop
7. Window
8. Control panel

Control Panel Description:

• A. Timer button [TIMER button]
• B. Power button [Power button]
• C. LCD display
• 1. Ambient temperature <M> and ice-making countdown <°F> indicators.
• 2. Ice-making (steady) or ice ready (flashing) indicator.
• 3. ON/OFF indicator.
• 4. Error codes: See “Troubleshooting” section on page 10.
• 5. Water low warning indicator.
• 6. Ice full warning indicator.
• 7. Time setting indicator: <H> = timer ON/OFF; <M> = ice-making cycle length
• D. Ice-making and timer decrease button [- button]
• E. Ice-making and timer increase button [+ button]

9. Hot air vent

10. Water drainage port

Diagram showing the ice maker's internal components and control panel. The control panel shows buttons for Timer, ON/OFF, -, and +. The LCD display has various indicators. The ice maker itself shows numbered parts like the water tank cover, unit top cover, ice basket, and drainage port.

UNPACKING YOUR ICE MAKER

• Remove the exterior and interior packaging. Check that the ice basket and ice scoop are included. If any parts are missing, please contact Customer Service.
• Clean the interior with a soft cloth dampened with plain lukewarm water. Take out the ice basket and scoop, and wash them in warm, soapy water. Then rinse, dry, and re-place the basket and scoop.
• Find a location for your ice maker that is out of direct sunlight and away from other sources of heat (e.g., a stove, furnace, or radiator).
• Place the ice maker on a flat, level surface.
• Be sure that there is at least 6 inches of space between the back and sides of your ice maker and any walls.
• After unpacking or moving the ice maker, allow 1 hour for the refrigerant fluid to settle before plugging in the appliance.
• The appliance must be positioned so that the plug is accessible.

Note: Fill with potable water only.

CONNECTING YOUR ICE MAKER

• Improper use of the grounded plug can increase the risk of electrical shock. If the power cord is damaged, please call Customer Service.
• This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug, which mates with standard three-prong wall outlets to minimize the possibility of electric shock.
• Plug your appliance into an exclusive, professionally installed, grounded wall outlet. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed to a certified electrician.
• This appliance requires a standard 110–120V, 60Hz electrical outlet with three-prong ground.

OPERATION PANEL AND DISPLAY AREA

Diagram showing the operation panel and display area. The display area shows indicators for ambient temperature, ice-making status, and power. The operation area shows the TIMER, ON/OFF, -, and + buttons.

Remove the water tank cover and pour potable water into tank. Be sure to keep the water level below the max level. See the FULL mark in the following picture. Re-place the cover at once to prevent foreign matter from entering the tank.

Diagram illustrating the water tank and its cover, with a 'FULL' mark indicating the maximum water level. A warning symbol is present.

Note:

• Do not pour water into the inner water tank located underneath the ice basket. This tank does not hold enough water, so ice-making performance will be negatively affected.
• When you plug in the unit, the power symbol [power symbol] will flash. Press the [ON/OFF button] to turn on the ice maker. The unit will start making ice cubes, and the ice-making symbol [ice making indicator] will remain on display. The upper left corner of the display shows the ambient temperature. After several minutes, this area will show a flashing number to indicate the countdown for the ice-making cycle. For example, "10M” means your ice will be ready in 10 minutes.
• When the ice maker harvest, the [ice ready indicator] will flash. Water will flow from the top water tank to the bottom tank through the solenoid valve, and the [water low indicator] will be on. When the bottom water tank is full, the [ice full indicator] will be off. Then the ice-making cycle will start again. When there is no water in the top water tank, the [water low indicator] will stay on. Turn off the unit and fill the tank with water again. Then restart the unit to make ice cubes. Or fill water directly and wait 20mins, the unit will restart.

Note:

• The ice-making cycle lasts about 13 to 25 minutes, depending on the ambient temperature. Depending on the initial water temperature, the first ice-making cycle may take a little longer. In an extremely hot environment, the ice-making cycle may vary but it will not exceed 35 minutes.
• If the ice cubes are not thick or large enough, during ice-making, press the [+] or [-] to change the ice-making cycle length in 1-minute increments to a maximum of 6 minutes. This can only be changed before the cycle starts.
• When the Ice Full indicator [ice full indicator] is on, the unit will stop. Take out the ice cubes and the unit will start working again.
• Pressing the [ON/OFF button] for more than 5 seconds while the ice maker is working will start harvest. Press the [ON/OFF button] again to turn off the unit.
• There is a timer setting function on the machine. When the machine is working, you can set the shutdown time at regular intervals. The appointment time would be invalid after shutdown. When the machine is turned off you can make an appointment to turn on the machine. Press the [TIMER button]. The display will show <1H>. Press [+] and [-] to set the time. The <H> will flash while you are setting the time. After 5 seconds idle, the <H> will stay on and your time setting will be saved.
• Water drainage: Remove the drain plug cap on the back of unit. Take out the silicone plug. Then drain out the water inside the ice maker. It is ideal to change the water every 24 hours and clean the unit every 3 days.

Diagram showing the water drainage port at the back of the unit, with 'OPEN' and 'CLOSE' indicators for the plug.

Note:

• Be sure the water tank, water filter, and water separator pipe are not clogged. If they are, clean them.
• The water temperature will affect the ice-making capacity. The lower the water temperature, the more ice cubes will be produced.
• The cooler the ambient temperature, the more ice cubes will be produced.
• Always use good-quality water to ensure smooth operation of the pump. Bad-quality water will cause the pump to make noise but will not keep the unit from working.
• The compressor restart 3mins later if you turn off the unit.

Tips & Maintenance

CLEANING AND MAINTAINING YOUR ICE MAKER

Before using your ice maker, it is strongly recommended to clean it thoroughly.

• Take out the ice basket.
• Clean the interior with diluted detergent, warm water, and a soft cloth.
• Rinse the interior with clean water. Drain out the water through the drainage port by removing the drain cap on the back and taking out the silicone plug.
• The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
• Dry the interior and exterior with a soft cloth.
• When the machine will not be used for a long time, open the drain cap to drain water completely out of the water tank.
• After using your ice maker for about 3 days, we suggest that you clean the unit. The water separator pipe and water filters in particular must be cleaned periodically.
• If you don't hear liquid flowing while the compressor and water pump are running, the water separator pipe may be clogged. Please turn off the unit. Then remove this pipe down and clean it. Clean each hole along the pipe wall, as shown in the following picture. After cleaning, reinstall the water separator pipe in its original orientation, making sure that the right end of the pipe is connected to the silicone pipe well.

Diagram illustrating the water separator pipe, showing its connection points and holes. The evaporator is also shown.

• Clean both water tanks with diluted detergent, warm water, and a soft cloth. Use clean water to rinse the inside of the unit. Drain out the water through the drainage port by removing the drain cap and plug on the back. Regular cleaning will keep the unit and your ice cubes sanitary, and also help the unit work normally.
• If, when you are cleaning the ice maker, you find that ice cubes are frozen onto the evaporator and cannot be removed easily, you can turn on the unit to start the ice-making process. Then press the [ON/OFF button] for at least 5 seconds so the unit can start the ice harvest process and melt the ice cubes. These steps will help you remove any stuck ice cubes.
• How to completely drain the internal tank and large water tank: The water in the large water tank is kept out of the drainage port by the water valve. If you want to drain out all the water, please plug on the unit but do not start it. Then remove the drainage port cap at the back. Wait a few minutes and then all of the water will flow out.

Specifications

TECHNICAL PARAMETERS

CIRCUIT DIAGRAM

Circuit diagram for the ice maker, detailing the electrical connections including power supply, compressor, solenoid valve, water pump, fan, and various sensors and control panel components. Key components include: Power Supply, Compressor, Solenoid Valve, Magnetic Control Switch, DC Water Valve, DC Water Pump, DC Fan Motor, Liquid Level Switch, and sensors for suction pipe and room temperature, all connected via a control panel with MCU and LCD.

Warranty

Euhomy offers a limited 1-year warranty ("warranty period") on all of our products purchased new and unused from Euhomy company, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period. The warranty does not apply where damage is caused by other factors, including without limitation:

• (a) normal wear and tear;
• (b) abuse, mishandling, accident, or failure to follow operating instructions;
• (c) exposure to liquid or infiltration of foreign particles;
• (d) servicing or modifications of the product other than by Euhomy;
• (e) commercial or non-household use.

The Euhomy warranty covers all costs related to restoring the proven defective product through repair or replacement of any defective part and necessary labor so that it conforms to its original specifications. A replacement product may be provided instead of repairing a defective product. Euhomy's exclusive obligation under this warranty is limited to such repair or replacement. A receipt indicating the purchase date is required for any claim, so please keep all receipts in a safe place. Although greatly appreciated, the product registration is not required to activate any warranty and product registration does not eliminate the need for the original proof of purchase. The warranty becomes void if attempts at repair are made by non-authorized third parties and/or if spare parts, other than those provided by Euhomy, are used.

You may also arrange for service after the warranty expires at an additional cost. These are our general terms for warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you have an issue with a Euhomy product, please contact us (support@euhomy.com), and we will do our best to resolve it for you.

Troubleshooting

support@euhomy.com