Heatmiser neoAir V3 Wireless Smart Thermostat
neo Series
Compatibility
| Feature | Status |
|---|---|
| neoHub 2nd Generation | Y |
| neoHub Mini OT, neoHub Mini HW | Y |
| RF-Switch | Y |
| UH8-RF | Y |
| Mesh Networking Facility | N |
Specifications
| Feature | Setting | Feature | Setting |
|---|---|---|---|
| Temperature Range | 5-35°C, 41-95°F | Temperature Override Limit | Y |
| White Back Lit Screen | Y | Output Delay | Y |
| Built In Air Sensor | Y | Frost Protection (7°C - 17°C) | Y |
| Non-Programmable Mode | Y | Mesh Networking Facility | N |
| 5/2 Day Programming | Y | °C/°F Option | Y |
| 7 Day Programming Mode | Y | Remote Air Sensing Mode | Y |
| 24 Hour Mode | Y | Floor Sensing Mode | Y |
| Number of Heating Levels | 4 or 6 with Neo App | Remote Probe Included | N |
| Optimum Start | Y | Floor Temp Limit Protection | Y |
| Number of Switching Times (Timer mode) | 4 | Wireless Fail Safe Function | Y |
| Holiday Function | Y | RF Frequency | 868MHz |
| Keylock Function | Y | Accuracy +/- | 1°C |
| Temperature Hold Function | Y | Adjustable Switching Differential | 0.5°C to 3°C |
| Temperature Override | Y | Supply | 4 x AAA |
| Installed Dimensions | 90x90x23mm (L,H,D) | Weight | 172g |
Feature Table - Thermostat Mode/Thermostat + Timer Mode
| Feature | Description | Setting | Feature | Description | Setting |
|---|---|---|---|---|---|
| P3 | Failsafe | 00 = Disabled 01 = Enabled (Default) | 06 | Sensor Selection | 00 = Built in Sensor (Default) 01 = Remote Air Sensor 02 = Remote Floor Sensor 03 = Built in Sensor & Remote Floor |
| P2 | Pairing to UH8-RF | 00 - 99 = Receiver address, Zone No. & Type | 07 | Floor Temperature Limit | 20°C - 45°C (28°C = Default) |
| P1 | Pairing to RF-Switch | Commences countdown from 99 - 00 seconds. | 08 | Optimum Start | 00 - 05 Hours (00 = Default) |
| 01 | Pairing to Hub | Used to add zone to the neoHub | 09 | Rate of Change | Minutes to raise by 1°C |
| 02 | Switching Differential | 00.5 = 0.5°C 01 = 1.0°C 02 = 2.0°C 03 = 3.0°C | 10 | Not used on this model | |
| 03 | Frost Protection Temperature | 07° - 17°C (12°C = Default) | 11 | Not used on this model | |
| 04 | Output Delay | 00 - 15 Minutes (00 = Default) | 12 | Program Mode | 00 = Non-Programmable 01 = Weekday/Weekend (Default) 02 = 7 Day Programming 03 = 24 Hour Mode |
| 05 | Up/Down Temperature Limit | 00° - 10°C (00 = Default) | 13 | Temperature Format | 00 = °C, 01 = °F (00 = Default) |
Feature Table - Timer Mode
| Feature | Description | Setting | Feature | Description | Setting |
|---|---|---|---|---|---|
| P3 | Failsafe | 00 = Disabled 01 = Enabled (Default) | 01 | Pairing to Hub | Used to add zone to the neoHub |
| P2 | Pairing to UH8-RF | 00 - 99 = Receiver address, Zone No. & Type | 02 | Program Mode | 01 = 5/2 day 02 = 7 day 03 = 24 hour |
| P1 | Pairing to RF-Switch | Commences countdown from 99 - 00 seconds. |
Product Dimensions (mm) & Wiring Specification
The Heatmiser neoAir V3 thermostat has a square design with dimensions of 90mm width, 90mm height, and a depth of 23mm.
The unit features a clear digital display showing the current room temperature (e.g., 21.8°C) and status indicators. Navigation and adjustment buttons are located below the display.
The rear of the unit provides mounting points and electrical terminals for wiring. The product is compatible with remote air or remote floor sensors, which connect via specific wiring terminals as indicated in the diagram.
Dimensions: 90mm (Width) x 90mm (Height) x 23mm (Depth)
Wiring: Supports connection to remote air or remote floor sensors.
Certifications: CE mark [CE symbol], WEEE Registration Number: WEE/GF0052TQ [WEEE symbol].
