Operation
5. Left Trim
If the boat veers to the right while moving forward, slightly turn the "steering" control to the left until the boat moves straight.
6. Right Trim
If the boat veers to the left while moving forward, slightly turn the "steering" control to the right until the boat moves straight.
7. Rudder Setting
Turn the switch to the left to increase the turning radius. Turn the switch to the right to reduce the turning radius. A turning radius that is too small can cause the boat to tip over.
8. Capsize Recovery
If the boat capsizes, push and pull the throttle control backwards and forwards repeatedly until the boat flips upright.
9. Dive Mode
1. Pull the throttle control backwards, and the boat moves forward.
2. Push the throttle control all the way forward, then press the dive button. The boat will dive for approximately 3-5 seconds before rising to the surface.
Note: If the boat cannot dive after following instructions, adjust the rudder setting on the remote control to the right, then try diving again.
Alerts
Weak Signal and Low Power Alert
- When the transmitter beeps once repeatedly and the POWER RED light flashes, it indicates that the transmitter's battery is low. Replace all batteries in the transmitter with new ones.
- When the transmitter beeps twice repeatedly and the ALERT LED flashes GREEN, it indicates that the boat's battery is low. Bring the boat back immediately and replace or recharge the battery.
- When the transmitter beeps three times repeatedly and the ALERT LED is solid GREEN, it indicates that the boat is about to go out of range. Quickly steer the boat back within range or risk losing control of the boat.
Note: If the boat is diving and the transmitter beeps or has a green signal sometimes, that is normal and it may not happen every time with diving.
Parts List
| Part Number | Description |
|---|---|
| H153-01 | Receiving Plate |
| H153-02 | Motor |
| H153-03 | Battery |
| H153-04 | Steering Engine |
| H153-05 | USB Charging Line |
| H153-06 | Discharge Tube |
| H153-07 | Steering Engine Bar |
| H153-08 | Propeller |
| H153-09 | Tail Vane |
| H153-10 | Guiding Rudders |
| H153-11 | Screw |
| H153-12 | Spindle Tube |
| H153-13 | Body |
| H153-14 | Hatch |
| H153-15 | Display Racks |
| H153-16 | Silicone Waterproof Plug |
Changing the Boat's Waterproof Ring
Follow these steps to replace the waterproof ring:
- Place the tool on the waterproof ring.
- Push the tool downward to push out the waterproof ring on the boat.
- Take out the old waterproof ring.
- Install the new waterproof ring into the boat.
Please contact Support@force1rc.com with your order number and shipping address for fast and friendly service!
FCC Compliance Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
