Sonodyne | Residential, Studio, Install, Live, Cinema
Owner's Manual for SONOSYNE models including: SSW 2020 Front Firing Powered Subwoofer, SSW 2020, Front Firing Powered Subwoofer, Firing Powered Subwoofer, Powered Subwoofer, Subwoofer
File Info : application/pdf, 8 Pages, 7.62MB
DocumentDocumentSSW 2020 front firing powered subwoofer · owners manual INTRODUCTION · UNPACKING INTRODUCTION The SSW 2020 is a stereo passive subwoofer with both direct (4 Ohm) and 70/100V input, and a pair of highpass outputs for satellite speakers. 10 20 4 20 4 80W are available, by connecting to the respective input terminal. Selection between inputs (direct and 70/100V) is carried out with a slide switch. Also provided is a mode switch which provides stereo mode operation and mono mode operation (in case of 70/100V input). In mono mode, the subwoofers are connected in series while the highpass output is available from the left channel only. Connection to the subwoofer is via Euroblock terminals which greatly facilitates wiring. protective covers. Please ensure that the following are attached to the rear of the unit. 1. 2 x wall-mount brackets fitted to the rear plate 2. 3 x female headers of Euroblock terminals Inspect the speaker for any sign of damage. Please retain all packing materials in case you have to transport the unit in future. SSW 2020 · page 1 DIMENSION · 225.0 mm 480.0 mm 370.0 mm SSW 2020 · page 2 MOUNTING The SSW 2020 comes fitted with wall mount brackets so that you can hang it on the wall. Please follow the steps given below The wall mount bracket of SSW 2020 consists of 2 parts - one that is fitted to the cabinet and the other part a fish-plate and 2 screws, for transit purposes. First open the 4 screws, and remove the plate. Please see Fig.1 below FIG.1 OPEN BOTH SCREWS UNPACKED CABINET (REAR VIEW) WALL MOUNT BRACKETS Next, drill holes on the wall for the screws supplied, as per the following diagram, where you want to mount the SSW 2020. Please see Fig. 2 below STEP 1 FIG.2 294 Now fit the wall mounting brackets to the wall with the help of the screws supplied. Please see Fig. 3 below STEP 2 FIG.3 60 310 480 SSW 2020 · page 3 MOUNTING Hold the cabinet vertically and align it, so that the tongue of the cabinet bracket is just above the groove on the wall bracket. Lower the cabinet so that the pins on the cabinet bracket engage with the corresponding holes on the wall bracket. Please see Fig. 4 below STEP 3: MOUNT THE CABINET FIG. 4 SSW 2020 · page 4 REAR VIEW SSW 2020 · page 5 REAR VIEW 1. INPUT SELECT SWITCH This is a slide switch for input selection. When connecting the 4 Ohm speaker output of your amplifier to the input of the SSW 2020, keep the switch in DIRECT mode. When connecting the 70V or 100V output of your amplifier, keep it in 70/100V position. 2. MODE SWITCH This is a slide switch for stereo/ mono mode. If you have connected 2 channels of your amplifier output to the input of the SSW 2020, keep the mode switch in stereo position. If, however, the input is mono, as for instance, 70/100V output of an amplifier, keep the switch in mono position. In mono mode, the subwoofers are connected in series while the high-pass output is available from the left channel only. Do not connect speaker to right input and amplifier output to right input as this may cause malfunctioning. 3. DIRECT INPUT Connect the 4 Ohm speaker output of your amplifier to these terminals. There is a pair of terminals making connections 4. and the other for right channel. In stereo mode, the impedance of satellite speakers should be 4 Ohm for each channel. In mono mode, the satellite speaker connected to the left channel will only 5. 70/100V INPUT Connect the 70/100V output of your amplifier to this terminal of are printed on the rear plate. Connect the amplifier to the COM pin and any of the power tap pins. SSW 2020 · page 6 SPECIFICATIONS DESIGN ENCLOSURE TRANSDUCER COMPLEMENTS SPL @ RATED POWER IMPEDANCE, DIRECT INPUT AMPLIFIER POWER, DIRECT INPUT IMPEDANCE 70V IMPEDANCE 100V DIMENSIONS (H x W x D) MM COLOUR MOUNTS NET WEIGHT GROSS WEIGHT Front firing powered subwoofer, vented MDF 1 x 8" dual voice-coil subwoofer 40Hz ~ 200Hz 45Hz ~ 200Hz 90dB (half space) 109dB @ 80W 4 Ohm + 4 Ohm (stereo), 8 Ohm (mono) 150W + 150W 10W, 20W, 40W 20W, 40W, 80W 490, 245, 122 Ohm 500, 250, 125 Ohm 370 x 480 x 225 White/ Black Wall-mounting brackets 15.5kg 17.1kg NOTE: Due to continuous improvements, all specifications are subject to change SONODYNE, India· H.O.: 98 NB Block E New Alipore, Kolkata 700053 sonodyneofficial +91 9830855260 SonodyneMusic sonodyneofficial response@sonodyne.com www.sonodyne.com