Easee Equalizer

User Guide and Installation Manual

Introduction

This manual applies to both versions of the product: Easee Equalizer (E02-EQP) and Easee Equalizer HAN (E02-EQ). All instructions apply to both versions unless otherwise stated.

Purpose

This product is designed to optimize power consumption by automatically balancing the load between the Easee Charger(s) and the building. It is used to prevent overloads and power interruptions during electric vehicle charging.

The product must only be operated within the approved operating parameters and under the specified environmental conditions (see page 45). Do not use the product if it is damaged or not functioning correctly. Any use other than that specified herein is not permitted.

Operating Conditions

The product must be coupled with a charger and connected to a compatible meter using the supplied cable. For the Equalizer to function, the communication port of the Smart Meter must be activated in most cases. The Equalizer supports multiple Smart Meters. A full list of compatible meters can be found at easee.support.

A smartphone with an internet connection is required for installation and operation.

Optimal Performance

The Equalizer enables smarter, safer, and faster charging when the installation is scaled accordingly. To unleash its full potential, the rated current of the circuit breaker for the charger should be as high as possible compared to the main fuse. Even for 1-phase installations, a 3-phase cable is recommended to make the installation future-proof.

Product Overview

Equalizer Unit

Magnetic Back
Touch Button
LED Indicator

Cable

Includes specific cables for connection to Smart Meters (e.g., RJ12 to RJ12 for Equalizer, RJ12 to RJ45 for Equalizer HAN).

Wall Mounting Set

For non-metallic surfaces. Includes mounting hardware (e.g., screws).

Safety Instructions

Read the entire manual carefully before installing and operating the product. Observe the following guidelines:

Do not use the product if it is damaged or not functioning correctly.
Always have repair work carried out by an authorized electrician in accordance with local regulations.
This product is intended for use in dry environments only. If installed outdoors, it must be protected from the elements using an enclosure.
Do not immerse the product in water or other liquids.
Avoid direct sunlight or exposure to heat.
Keep the product away from open flames and extreme heat.
Ensure that children do not play with the product.

Technical Data

General

Product Dimensions (mm): H: 110 x W: 110 x D: 27.5
Packaging Dimensions (mm): H: 130 x W: 130 x D: 39
Operating Temperature: -20 °C to +50 °C
Weight: 95 g (Equalizer), 110 g (Equalizer HAN)
IP Rating: IP40
Power Supply: 5-30 V DC 100 mA (Equalizer), 20-32 V DC 30 mA (Equalizer HAN)
Connector: RJ12

Wiring

Cable Length: 1.5 m
Connectors: RJ12 to RJ12 (Equalizer), RJ12 to RJ45 (Equalizer HAN)
Extension possible: up to 15 m (Equalizer), up to 200 m (Equalizer HAN)

Visual representation of RJ12 (6 Pole) and RJ45 (8 Pole) connectors.

Maximum Transmitted Power

Radio: 25 mW at 863–870 MHz
WiFi: 50 mW at 2.4–2.472 GHz

Connectivity Options

Easee Link RF™ and WiFi¹
HAN (NVE/AMS) (Equalizer HAN) or P1 (Equalizer) Smart Meter Communication
Modbus connection to the energy meter²
Monitor power consumption with Easee App
RFID/NFC Reader

¹ WiFi is required for normal operation and future software updates. In case of no or unstable internet connection, Easee Link RF™ is used as a backup in small installations with a primary charger. Easee Link via radio can be limited by walls, concrete, or other obstacles.

² For supported energy meters only.

Installation

Customer Setup

Follow these steps if you are installing the Equalizer as a private customer in your own home.

1. HAN Port Activation

In Scandinavia, the communication port on the Smart Meter is likely not activated. Contact your energy provider to enable the HAN port for use with the Equalizer. If you are not in Scandinavia, proceed directly to step 2.

2. Easee App Download

Scan the QR code to download the Easee App and create a free account. [QR code for easee.com/app]

Visual: A smartphone displaying the Easee app interface with an option to "Add Product".

3. Equalizer Setup

Add the Equalizer in the app, follow the on-screen installation guide, and get ready to manage your energy more intelligently!

Visual: A Smart Meter labeled "Smart Meter" with a port labeled "HAN / P1".

Installer Setup

Follow these steps if you are an installer and use the Installer App to configure the Equalizer in large commercial installations or private homes.

1. Installer App Download

Scan the QR code to download the Installer App and create a free account. [QR code for easee.com/installer-app]

2. Equalizer Setup

Add the Equalizer using the Installer App to a new or existing charging location and follow the on-screen installation guide to set it up.

3. Smart Meter Connection

Connect the Equalizer to the Smart Meter using the supplied cable. The Equalizer will appear in the Easee Portal after a while.

Visual: A Smart Meter labeled "Smart Meter" with a port labeled "HAN / P1".

Daily Use and Operation

Meaning of LED Colors

White, fast blinking – Starting
White, every 10 sec. – Normal operation
Red-White, alternating – WiFi not added³
Red, blinking – No data from energy meter⁴
Red, every 10 sec. – Error⁵
Purple, every 10 sec. – Offline operation⁶

Checking Connectivity and Power Consumption

Touch the Easee logo in the center to check power consumption:

Blue, fast blinking – High power consumption
Blue, slow blinking – Low power consumption
Count blink signals for percentage: 1 blink (10%), 2 blinks (20%), up to 10 blinks (100%)

Press and hold the Easee logo for 3 seconds to check connectivity. You will see 2 sets of blink signals:

Blinks – Easee Link RF Status⁷
Blinks – WiFi Status

Status indicators:

Green – Connected
Red – Not connected

³ Use Easee App to set up WiFi.

⁴ Contact your utility provider to activate the HAN connection.

⁵ Go to http://easee.support.

⁶ Check your internet connection.

⁷ After startup, it may take a few minutes for the Easee Link RF status to turn green.

Practical Details

Warranty

The device is free from material defects and complies with the laws and regulations for consumer protection in the country where the product is purchased. A limited warranty of 3 years* applies to all correctly installed Easee hardware. *In some countries, the warranty may be longer.

Standards

Easee AS hereby declares that the radio equipment of type Easee Equalizer (E02-EQP) and Easee Equalizer HAN (E02-EQ) complies with Directive 2014/53/EU. The EU Declaration of Conformity is available at: easee.support.

Storage

The product should be stored in a temperate, dry, and well-ventilated room to preserve the packaging and its contents. Relative humidity should not exceed 80%, and no corrosive gases should be present. The storage or transport environment should never exceed the limits specified in the technical data.

Disposal

A crossed-out waste bin symbol indicates that a product and its accessories must not be disposed of with household waste at the end of their life cycle. Free collection and drop-off points may be available near you for returning old equipment. Observe local regulations for proper and environmentally sound disposal. If the old electrical or electronic equipment contains personal data, you are responsible for deleting it before returning it. This can be done via the Easee App or the Installer App.

Maintenance

This product requires no maintenance. If it needs to be repaired, please contact your Easee provider.

Returns and Claims

For returns and claims regarding your product, contact your dealer or Easee Customer Support at easee.support.

Legal Information and Contact Details

This document contains information that is subject to change without notice.

The latest version of this publication can be downloaded at http://easee.support.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including, but not limited to, copying, recording, retrieving data, or computer networks without the written permission of Easee AS.

Easee and all other Easee product names and slogans are trademarks or registered trademarks of Easee AS. Easee products can be protected by one or more patents.

All other products and services mentioned may be trademarks or service marks of their respective owners.

Illustrations of the product and user interface are exemplary and may differ from the actual appearance.

Contact Details

Easee AS
Grenseveien 19
4313 Sandnes, Norway
Org. nr: 920 292 046

You can find additional contact details for your country at easee.com.

	Easee Equalizer Installer and User Guide Comprehensive guide for installing and using the Easee Equalizer, covering technical specifications, setup instructions for customers and installers, LED indicators, and warranty information.
	Vilkår og betingelser for Easee-produkter og skytjenester Offisielle vilkår og betingelser for bruk av Easee-produkter for elbillading, smarte energistyringsløsninger og tilhørende skytjenester. Dette dokumentet beskriver brukeravtaler, ansvar, datahåndtering og juridiske aspekter for forbrukere og partnere i Norge.
	Easee Terms and Conditions for Products and Cloud Services Official terms and conditions governing the use of Easee's electric vehicle charging products, smart power management hardware, cloud services, applications, and related digital services. Covers user acceptance, responsibilities, liability, and support.
	Easee Charging Robot: Important Product Information for Home, Charge, and One Models Comprehensive product information for Easee Charging Robot models (Home, Charge, One), covering intended use, operating conditions, safety instructions, declarations of conformity, warranty, and support.
	Allmänna Villkor för Easees Produkter och Molntjänster Allmänna villkor som reglerar användningen av Easees elfordonsladdningsprodukter, laddningsrobotar, molntjänster och relaterade applikationer.
	Easee Charge Pro: Professional EV Charging Solution for Installers Explore the Easee Charge Pro, a professional EV charging solution engineered for installers. Learn how it simplifies installation, boosts reliability, and drives profitability for large-scale EV charging projects.
	Easee Home & Easee Charge User and Installation Guide Comprehensive user and installation guide for the Easee Home and Easee Charge electric vehicle charging stations, covering setup, operation, safety, and technical specifications.
	Easee Charge Pro: Profesjonell Elbillader for Installatører Oppdag Easee Charge Pro, den profesjonelle ladeløsningen for elektriske kjøretøy designet for installatører. Forenkle installasjon, øk lønnsomheten og lever konkurransedyktige prosjekter med avanserte funksjoner som innebygd MID-måler og skybasert administrasjon.