Introduction
The information in this leaflet applies to Easee Equalizer P1 (E02-EQP) and Easee Equalizer HAN (E02-EQ), unless specified otherwise.
Read the Important product information guide in the product packaging or at easee.com/manuals before using the product.
Optimal performance
The Equalizer makes it possible to charge smarter, safer and faster if the installation is scaled accordingly. To enable its true potential, the rated value of the chargers circuit fuse should be as high as possible compared to the main fuse.
Product overview
The Easee Equalizer features a magnetic backside, a touch button, and an LED indicator.
Includes one cable.
Includes one wall mounting kit for non-metallic surfaces.
Technical specifications
General
| Specification | Details |
|---|---|
| Dimensions Product | 110 x 110 x 27.5 mm (H x W x D) |
| Dimensions Product Packaging | 130 x 130 x 39 mm (H x W x D) |
| Permitted temperature | -20 °C to +50 °C |
| Weight | 95 g (Equalizer P1) 110 g (Equalizer HAN) |
| IP degree | IP40 |
| Supply | 5-30 V DC 100 mA (Equalizer P1) 20-32 V DC 30 mA (Equalizer HAN) |
Cabling
| Specification | Details |
|---|---|
| Cable length | 1.5 m |
| Custom made cable | RJ12 to RJ12 (Equalizer P1) RJ12 to RJ45 (Equalizer HAN) |
| It can be extended using an extension cable | up to 15 m (Equalizer P1) up to 200 m (Equalizer HAN) |
Diagram shows RJ12 connector (6 pins) and RJ45 connector (8 pins).
Connectivity
- Easee Link RF™ and WiFi¹
- HAN (NVE/AMS) (Easee Equalizer HAN) or P1 (Easee Equalizer P1) smart meter communication
- Modbus connection to energy meter²
- Monitor power consumption with the Easee App
- RFID / NFC reader
¹ WiFi is required for normal operation and for future software updates. Installations with multiple master chargers need to be connected to the same WiFi for load balancing to work. Easee Link RF (TM) via radio may be limited by walls, concrete or other obstacles.
² Only for supported meters.
Installation
Customer setup
Follow these steps if you are a private customer installing the Equalizer in your own household.
-
1 HAN port Activation
In Scandinavia, the communication port on the smart meter is most likely not activated. Contact your utility company to open the HAN port for use with the Equalizer. If you are not in Scandinavia, skip to step 2.
-
2 Easee App Download
Scan the QR code to download the Easee App and create a free account.
[QR code for Easee App download]
-
3 Equalizer Setup
Add the Equalizer in the app, follow the on-screen installation guide and get ready to balance your energy smarter than ever before!
Illustration of a smart meter with 'HAN/P1' indicated.
Installer setup
Follow these steps if you are an installer and use the Installer App to configure the Equalizer in large commercial installations or private households.
-
1 Installer App Download
Scan the QR code to download the Installer App and create a free account.
[QR code for Installer App download]
-
2 Equalizer Setup
Add the Equalizer to a new or existing charging site using the Installer App and follow the on-screen installation guide to set it up.
-
3 Smart meter Connect
Connect the Equalizer to the smart meter using the provided cable. The Equalizer will appear in the Easee Portal after a while.
Illustration of a smart meter with 'HAN/P1' indicated.
LED colours meaning
- White, fast flashing – Booting
- White, breathing every 10s – Normal operation
- Red / white, switching – No WiFi added³
- Red, flashing – No data from power meter⁴
- Red, breathing every 10s – Error⁵
- Purple, breathing every 10s – Offline operation⁶
Touch the Easee logo in the middle to check power consumption:
- Blue, fast flashing – High power consumption
- Blue, slow flashing – Low power consumption
- Count the flashes for percentage – 1 flash (10%), 2 flashes (20%), up to 10 flashes (100%)
Hold the Easee logo for 3 seconds to check connectivity. You will see 2 flashes:
- 1st flash – Easee Link RF status⁷
- 2nd flash – WiFi status
- Green – Connected
- Red – Not connected
³ Use the Easee App to set up the WiFi.
⁴ Contact your utility company to activate the HAN port.
⁵ Go to easee.support.
⁶ Check your internet connection.
⁷ After booting, it can take a few minutes before Easee Link RFTM status flashes green.
Practical details
Warranty
The device is free from material defects and is in accordance with laws and regulations for consumer protection in the country where the product is purchased. All correctly installed Easee hardware is covered by our 3 years* limited warranty.
*Some countries may have extended warranty.
Returns and complaints
Contact your distributor or Easee Customer Support at easee.support regarding the return and complaint of your product.
Disclaimer
The information in this document is for information purposes only, is provided as is, and may be subject to change without notice. Easee ASA including its subsidiaries does not accept any liability for the correctness or completeness of the information and illustrations, and is not liable or responsible for your considerations, assessments, decisions or absence of such, or other use of the information in this document.
No part of this publication may be re-published, reproduced, transmitted or re-used in any other form, by any means or in any form, for your own or any third-party's use, unless otherwise agreed with Easee or its subsidiaries in writing. Any permitted use shall always be done in accordance with good practice and ensure that no harm may be caused to Easee or by misleading the consumer.
Easee and Easee products, product names, trademarks and slogans, whether registered or not, are Easee's intellectual property and may not be used without Easee's prior written permission. All other products and services mentioned may be trademarks or service marks of their respective owners.
September 2023 – Version 1.01 © 2023 by Easee ASA. All rights reserved.
Easee ASA
Vassbotnen 23
4033 Stavanger, Norway
www.easee.com
Easee electric car chargers – Small. Smart. Full of Power.
Easee Help
