Legrand radiant® WNRL10 Smart Switch with Netatmo

Overview

The radiant® WNRL10 Smart Switch with Netatmo offers advanced control for your home lighting. This guide provides instructions for installation, setup, and basic operation.

Key Specifications:

Legrand reserves the right to change specifications without notice.

Before You Start

Important Safety Information:

• Review this entire guide before installation. Consult a qualified electrician if you have any questions or concerns about your abilities.
• Warning: Incorrect installation can result in death, serious injury, or damage to your home or devices.
• Caution: For dry, indoor use only. Do not use to power medical equipment. Do not exceed device load ratings.
• Connect only to a 120 VAC, 60 Hz power source. Always use copper wire and follow all applicable electrical codes.

What You Need

Required Tools:

• Phillips-head screwdriver
• Flat blade screwdriver

Recommended Tools:

• Voltage tester
• Pliers
• Wire cutter
• Wire stripper
• Electrical tape
• Flashlight
• Wiring leads (included)
• Wire nuts (included)

Installation & Setup

1. Turn off power to the device at the circuit breaker.

   Flip the existing light switch multiple times to confirm power is off. Ensure power is off to all devices in the electrical box.

2. Remove existing device.

   Identify the following wires:

   • HOT or LINE: Receives power from the circuit box.
   • LOAD: Directs power to your light(s).
   • NEUTRAL: Required for switch operation; creates a path to return current to the power source.
   • GROUND: Provides a safe path for electricity in case of a short circuit.

3. Wire the Smart Switch.

   Use the included wire nuts to secure connections:

   • Connect the WHITE neutral wire from the switch to the neutral wires in the box using a red wire nut.
   • Connect the LOAD wire from the switch to the load wire(s) in the box.
   • Connect the HOT wire from the switch to the hot wire(s) in the box.
   • Connect the GREEN ground wire from the switch to the ground wire(s) in the box.

4. Secure the Smart Switch.

   Fold wires neatly into the electrical box, taking care not to pinch them. Use the included screws to secure the smart switch to the electrical box. Do not fully tighten the screws yet.

5. Test the Smart Switch.

   Turn the power back on at the circuit breaker. Press the switch paddle to turn the light on and off. If the device is not powering on, check that the "HOT" and "LOAD" wires are not reversed.

6. Attach the Wall Plate.

   Use the provided sub-plate screws to secure the sub-plate to the smart switch. Tighten the device screws to secure the switch to the electrical box. Angle the UP end of the wall plate over the top edge of the sub-plate and push it down and in until it snaps into place. To remove the wall plate, insert a flat blade screwdriver into the slot under the plate and twist gently.

7. Set Up Your System.

   Download and launch the Legrand Home + Control app from the App Store or Google Play. Follow the step-by-step instructions within the app to connect your smart device to your home network and control it.

Getting to Know Your Switch

Components:

• 1. Paddle Switch: Press the top to turn the light on, and the bottom to turn it off.
• 2. LED Locator Light: Indicates the current state of the device.
• 3. EZ Button: Used to enter setup mode.

LED Locator Light Explanations:

Resetting to Factory Defaults:

Deleting the device from the app will reset it to factory defaults. To manually reset, press and hold the EZ button for 10 seconds until the LED blinks red, then release. The LED will turn solid red upon completion.

Regulatory Information

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to two conditions: it may not cause harmful interference, and it must accept any interference received. This equipment has been tested and found to comply with Class B digital device limits, designed for reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If interference occurs, try reorienting the antenna, increasing separation, or connecting to a different circuit. Changes not expressly approved by the manufacturer may void the warranty and user authority. Contains FCC ID: 2AU5D982057.

IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to two conditions: it may not cause interference, and it must accept any interference received. This equipment meets SAR evaluation limits (RSS-102 Issue 5) at a minimum separation distance of 10 mm. Changes not expressly approved by the manufacturer may void the warranty and user authority. IC: 25764-982057, HVIN: 982057.

Limited One Year Warranty

Legrand warrants this product against defects in workmanship or material for one year from the date of purchase. This warranty covers repair or replacement at Legrand's option. It is in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. This warranty does not cover labor costs for removal or reinstallation. Legrand is not liable for incidental or consequential damages. Some states may have different limitations. For warranty service, contact Legrand, Syracuse, New York 13221, for instructions.

Support & More Information

Questions? We’re here to help.

• Phone: 1-877-833-3303 (8:00 a.m. to 8:00 p.m. EST, M-F)
• Email: smartlighting@legrand.us
• Chat: https://www.legrand.us/radiant/smart-lighting.aspx (Click the chat icon)

For the most recent instruction sheets or more information, visit https://www.legrand.us/p/wnrl10wh.

For covering patents, see www.legrand.us/patents.