Redragon ARCO K670-RGB Mechanical Keyboard

US UK - Dear User

Thank you for choosing a Redragon product. To protect your rights and for better customer service, please read the following warranty rules carefully.

• Within 18 months of purchase date, repair is guaranteed for failure due to electrical circuit problems. Other damages, such as disassembly, hard impacts, submersion into water, plugging into improper current or voltage, and damage caused by natural disasters such as fire, flood, or earthquake are not included.
• Consumable parts (such as foot pads) and spare parts replacement are not included in our warranty.

Function Introduction

The keyboard connects to your computer's USB port without needing to install drivers or software.

Backlight Brightness Control

• Press and hold the [FN] key, then press the arrow key "↑" to increase backlight brightness.
• Press and hold the [FN] key, then press the arrow key "↓" to decrease backlight brightness.

Backlighting Effects

• FN + [Insert]: Switch between 3 backlighting modes: 1. The trial of Light; 2. Breathing; 3. Normally on.
• FN + [Home]: Switch between 3 backlighting modes: 1. Ripple Graff; 2. Pass without Trace; 3. Coastal.
• FN + [Page Down]: Switch between 3 backlighting modes: 1. Both ways; 2. Surmount; 3. Fast and the furious.
• FN + [Del]: Switch between 3 backlighting modes: 1. Go with the stream; 2. Clouds fly; 3. Winding Paths.
• FN + [Page Up]: Switch between 3 backlighting modes: 1. Hurricane; 2. Accumulate; 3. Digital Times.
• Customized Backlighting Mode: Press FN+[~] to prepare for setting key colors. The [~] key acts as your palette. Press FN+[→] for color switching (9 modes including 8 color options and light-off mode). The 3 indicators [Num, Cap, Scroll] will twinkle simultaneously during customization. Press the desired key to set its color. Press FN+[~] again to save the customization.
• Switchable Backlighting Modes on Sides: Press FN+PAUSE to switch lighting modes.
• Adjustable Lighting Speed on Sides: Press FN+SCRLK to adjust lighting speed.
• Restore Factory Settings: Press FN+PRTSC.
• Disable [WIN] Key: Press and hold the [FN] key, then press the left [WIN] key to turn off the [WIN] key function, preventing accidental exit from games. Repeat the operation to restore the function.
• Adjustable Lighting Direction: When backlit keys are cycling through effects, press FN + [-] to change directions.
• Adjustable Colors: Press FN+[→] to cycle through backlight colors (8 color options).
• Adjustable Lighting Speed: Press FN+ [-] or FN+ [+] to adjust light rotating speed.

Multi-media Keys (FN+F1~F12)

FAQ

1. Question: If the keyboard doesn't respond, what should I do?

   Answer: Please check if the keyboard's USB cable is correctly inserted into the corresponding USB port on the computer, or try another USB port on the computer.

2. Question: What should I do if liquid is spilled on the keyboard?

   Answer: If you spill liquid on the keyboard, please unplug the keyboard's USB cable from the computer immediately. Wipe off excess liquid and place the keyboard in a dry and ventilated place. Ensure the keyboard dries naturally before the next use.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.