SIG SAUER SV50-LRF Thermal Sight
This document provides instructions and specifications for the SIG SAUER SV50-LRF Thermal Sight.
Attention!
Export of SV50-LRF models may have export limitations depending on the laws in your region.
⚠ The proper usage of the device is important for safe exploitation! Therefore, read carefully the present manual!
⚠ If the device was left in storage for a longer period of time, before exploitation, check its functionality.
⚠ Disassembling of the device is prohibited, except in authorized repair centers.
⚠ The external optical surfaces should be clean at all times. Touching the optical surfaces with bare hands is not recommended.
⚠ Sand and sea water can damage the optical coatings!
⚠ Do not point the device directly at the sun!
⚠ Image performance is dependent on scenery and atmosphere conditions. Contrast in the same image may vary as a function of the time of day due to the effect of the sun. For example, at sunset, objects will have absorbed different levels of heat, resulting in greater temperature differences and better contrast.
⚠ When left in storage for a longer period of time, batteries have to be removed and stored in polyethylene bags to prevent contact with metal. It is recommended to recharge the batteries every two to three months.
⚠ When carrying or transporting the device, put the protective lens cap!
⚠ Condensation can cause fogging of the optical surfaces! Condensation occurs when the temperature or humidity changes as follows:
- When moving the device from cold to warm place or vice versa;
- In places with high humidity.
When equalizing the temperature of the device with the environment, the condensation disappears. Use the towel to remove moisture.
⚠ Clean the lens surfaces with the Lens Cloth or with the napkin!
⚠ LEGAL NOTICE
Before attaching to weapons, check the regional legal regulations in the area of application. The attachment to a weapon is always the sole responsibility of the user.
Device Operations
Power Off
Long press Middle button to power off the device.
Take Photo/Video On-boarding
Short press [Right Arrow] button to take a photo.
Please note the following before using:
- You cannot take photos/videos while connecting with PC. Otherwise, the photos/videos are not actually saved.
- Photos/videos can only be taken when WiFi is on.
- When you take photos, do not press too quickly.
How to Replay on PC?
Connect the Type-C USB cable to PC.
A visual representation shows navigating a PC's file system: "This PC" > "Hard Disk Drives" (listing C:, D:, E:, F:, G:) and "Devices with Removable Storage" (listing USB Drive H:). A sub-window shows the contents of the USB drive, with folders like "picture" and "video", indicating where to find saved photos and videos.
Storage and Transportation
- Before storing, clean the device thoroughly (if its surface has moisture, dust, or traces of dirt).
- Make sure that there are no traces of moisture, and the battery compartment is empty.
- For short periods, the device can be stored in a suitable soft pack, bag, or cartridge box.
- For long-term storage, the premises must be dry, enclosed, unheated, and ventilated.
- During storage, avoid exposure to aggressive environments, temperatures below -50°C and above +60°C, relative humidity greater than 80%, and prolonged periods of direct sunlight.
- Before each transportation, the product should be neatly packed in its original packaging (transport bag), with all items and accessories carefully and steadily placed in the bag. The bag should then be steadily placed in the transport suitcase.
- The product can be shipped via all types of transport at different distances and altitudes up to 12000 m.
SV50-LRF Specification
| Detector Type | Uncooled Vox |
| Resolution | 640x512 |
| Frame rate | 50Hz |
| Pixel | 12μm |
| Spectral range | 8-14μm |
| NETD | < 20mk |
| Optical Characteristics | |
| Objective lens | 50mm |
| Magnification | 1.5X |
| FOV(H×V), m@100m | 8.8×7° |
| Close-up range | 5m |
| Functions | |
| Palettes | 2 |
| WIFI | Yes |
| Storage capacity | 32G |
| Display | |
| Type | OLED |
| Resolution | 1024×768 |
| Power Supply | |
| Battery | 2×18650 |
| External power supply | 5V Type-C |
| Operating time (at t=22°C) | 12h |
| Physical Characteristics | |
| Weight without battery | ≤500g |
| Dimension | ≤179×101×70mm |
| Environmental Compatibility | |
| Ingress protection rating | IP67 |
| Operating temperature | -20°C-50°C |
| Storage temperature | -40°C-60°C |
FCC Caution
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
§ 15.21 Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
