Safety Notes
Read all safety notes and all instructions. Failure to follow the notes and instructions may result in electric shock, fire or serious injury. Save this manual for future reference.
DANGER: Electric shock caused by high voltages inside!
Within the unit there are areas where high voltages may be present. To reduce the risk of electric shock do not remove any covers unless the AC mains power cord is removed. Covers should be removed by qualified service personnel only. There are no user-serviceable parts inside.
DANGER: Electric shock caused by short circuit!
Always use proper ready-made insulated mains cabling (power cord) with a protective contact plug. Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.
Power supply
Notice:
Malfunction or damage to equipment!
Ensure that the input voltage (AC outlet) matches the voltage rating of the product. Failure to do so could result in damage to the product and possibly the user. Unplug the unit before electrical storms occur and when unused for long periods of time.
Operating conditions
Always install and use the device in accordance with these instructions.
Notice:
Malfunction or damage to equipment!
This device has been designed for indoor use only. Do not expose the device to any liquid or moisture. Do not install the unit near any direct heat source. Keep the unit away from naked flames. Do not block areas of ventilation. Failure to do so could result in fire.
Handling
Notice:
Malfunction or damage to equipment!
To avoid breakage, do not apply excessive force to the switches or controls.
CAUTION: Pinching hazard
Be careful, the sliding key cover may pinch your fingers. Do not insert a finger or hand into any gaps on the sliding key cover or instrument.
WARNING: Hearing damage
Using the instrument or headphones for a long period of time at a high or uncomfortable volume level can cause permanent hearing loss. Use the piano and headphones at a moderate volume level.
Notice:
Damage to equipment!
When the top cover is closed, you can put any objects on it. To avoid falling objects, be careful where you place monitors, a laptop, speakers or other devices on the piano.
Main Features
Better than acoustic pianos
The Thomann DP-S 307 UP has a brilliant sound quality that is unmatched by some acoustic pianos. It features pure and true sound with each tone that remains unchanged for the lifetime of the instrument.
Rich acoustic sounds
Eight popular, high-quality sounds are built into the Thomann DP-S 307 UP. Some of the sounds include a stereo grand piano and a jazz trio. You can utilize the layer function to simultaneously play two sounds.
Luxurious design
High-gloss ebony paint provides an exquisite feel to match your specific taste. It will always stand out, no matter where you have it, because of its distinguished design.
No need for tuning
Tuning is a difficult and expensive process. Tuning is not required when you have this piano in your hands. We can guarantee that the sound will remain unchanged, no matter how long you have this piano in your possession. Through advanced technological advances, we have made this possible for your convenience.
Keyboard and effects
You can play the piano with graded hammered action keys and adapt various effects to the selected source.
Multi-purpose
The Thomann DP-S 307 UP features wireless device connection as well as a USB audio interface for sound recording and VST (Virtual Studio Technology) plug-ins. This product also features clean true-sound speakers which are untainted by any filters, providing only the purest of sounds. What you play is what you hear; what you hear is what you get.
Perfect link with the computer
You can connect the Thomann DP-S 307 UP with a computer via a USB cable. In addition, you can operate lots of software with Thomann DP-S 307 UP, such as multimedia players, recording software, lesson programs and so on.
Unlimited sound samples
The Thomann DP-S 307 UP can be connected to a computer with a USB cable. That means, you can use any VSTs installed in your computer as the sound samples of the Thomann DP-S 307 UP.
Digital audio workstation
The Thomann DP-S 307 UP is equipped with a USB audio interface and is compatible with ASIO 2.0 and CoreAudio drivers. It can be used as a professional digital audio workstation.
Control Panel
Please open the top cover of the Thomann DP-S 307 UP to access the control panel. It is located inside the cabinet. For reasons of better visibility, the left-hand and the right-hand side of the control panel are shown separately in the following two figures.
Left-hand side of the control panel
The left-hand side features several buttons for selecting sounds and effects, along with a master volume slider.
- 1. MASTER VOLUME slider: Adjusts the volume for the output, headphones, and connectors.
- 2. FX SOURCE: Selects the source for effects (MIC, LINE, SOUND). SOUND is preselected.
- 3. FX TYPE: Selects internal effects (REVERB, CHORUS, ECHO). REVERB is preselected.
- 4. FX DEPTH: Controls the amount of effect mixed in (LOW, MID, HIGH). LOW is preselected.
- 5. SOUNDS: Buttons to select a sound (Single Mode). Holding down one button while pressing another mixes two sounds (Layer Mode).
- 6. DEMO FUNCTION: Pressing FUNCTION + INT. SOUND OFF simultaneously starts sound demos. Pressing a flashing sound button replays its demo.
- 7. DEMO INT. SOUND OFF: Switches off the internal sound completely.
Right-hand side of the control panel
The right-hand side includes speaker level controls, a power switch, and a wireless indicator.
- 8. POWER switch: Turns the unit on/off once the power cord is connected.
- 9. Wireless audio module indicator: Shows the status of the wireless module.
- Sensitivity knobs: Control the left and right speaker output levels individually.
Functions
Touch sensitivity
This function allows setting the touch sensitivity. While holding down the FUNCTION button, select one of the touch sensitivity keys (SOFT, MID, HEAVY, or FIX) on the keyboard. The default setting is MID.
Visual representation of keys: SOFT (B1), MID (C2), HEAVY (D2), FIX (E2).
Transpose
This function shifts the pitch of the entire keyboard up or down in semitone intervals (up to 12 semitones). While holding FUNCTION, select a transposition key between C3 and C5. Press FUNCTION + C4 to return to the original pitch.
Visual representation of keys: C3 to C5 for transposition, with labels -12, 0, +12.
Layer mode
When playing two instruments in layer mode, adjust the volume of the second instrument. While holding FUNCTION, press DOWN [-] or UP [+] keys to set the volume. Press FUNCTION + E5 to decrease the level.
Visual representation of keys: E5, G5 for adjusting layer balance.
Microphone level
Control the microphone input level. While holding FUNCTION, press the corresponding key to adjust volume. C6 decreases the level, E6 increases it. A high-impedance microphone is required.
Visual representation of keys: C6 (decrease), E6 (increase) for microphone level.
Rear Panel
The rear panel of the Thomann DP-S 307 UP provides the connectors shown in the following figure.
Diagram showing the rear panel connectors: AC power input, MIDI IN/OUT, USB, LINE IN/OUT, MIC input, and Headphone output.
| Connector | Description |
|---|---|
| AC cord connector | AC power 220-240 V, 50/60 Hz |
| MIDI IN/OUT connectors | Connect to other MIDI devices (sequencer, keyboards). MIDI OUT sends data, MIDI IN receives data. |
| USB connector | Connects to a computer using the provided USB cable. |
| LINE IN/OUT connectors | LINE IN: Connect audio players (MP3, CD) to play through DP-S 307 UP speakers. LINE OUT: Connect to external audio devices (amplifiers, speakers) to output DP-S 307 UP sound. |
| MIC input | Connect a dynamic microphone with a TRS cable for listening and recording. |
| Headphone output | Two standard 1/4-inch jacks located on the left side under the keyboard. |
The Pedals
The 3 pedals are the Soft, Sostenuto, and Sustain pedals. They function similarly to those on an acoustic piano.
Soft pedal
Notes played while this pedal is down will sound softer.
Sostenuto pedal
Pressing this pedal sustains only those notes depressed at the same time the pedal is pressed; future notes played will be unaffected.
Sustain pedal
Pressing this pedal causes notes to sustain even when you lift your fingers from the keys.
Wireless Audio Setup
Overview of the Bluetooth wireless audio module
Diagram of the Bluetooth wireless audio module with numbered controls:
- 1. Earphone jack
- 2. Power switch
- 3. Fast-Forward button
- 4. Rewind button
- 5. Microphone
- 6. Indicator light
- 7. Adaptor jack
- 8. Play/Pause/Stop button
- 9. Volume up button
- 10. Talk button
- 11. Volume down button
Charging the wireless audio module
This module has a rechargeable internal battery. Fully charge the battery before first use. Insert the adapter into the jack and a power outlet; the indicator light turns red.
Pairing with your wireless device
- Enter pairing mode: Slide the power switch while pressing and holding specific buttons. The indicator light turns blue. If it's the first use, it enters pairing mode automatically.
- Search and connect with your Bluetooth device according to its user's guide. (Bluetooth PIN: 0000, 4 zeros)
Note:
When paired, press [▶️||] to reconnect via Headset Profile or Hands-Free Profile, or press [▶️||] to reconnect via Advanced Audio Distribution Profile.
Using music control functions
- Press [▶️||] to play/pause music.
- Press and hold [▶️||] to stop playback.
- Press [⏪] or [⏩] to skip tracks.
- Press and hold [⏪] or [⏩] to scan backward or forward in a file.
- Press [▲] or [▼] to adjust the volume.
Specifications
- Supported profiles: Hands-free headset, advanced audio distribution, audio/video remote control
- Operating range: Up to 10 meters (30 feet)
Connection to External Devices
The connection to external MIDI devices
What is MIDI?
MIDI (Musical Instrument Digital Interface) is an international standard for connecting and transferring data between electronic musical instruments, computers, and other devices.
What can you do with MIDI?
Use the Thomann DP-S 307 UP to control other instruments, or be controlled by them. Use a sequencer to create complex musical pieces. MIDI signals can be transmitted to other instruments or recorded by a sequencer.
Diagram showing MIDI IN and MIDI OUT ports on the DP-S 307 UP and a generic MIDI device.
Connections
Connect the MIDI OUT connector of the transmitting (master) device to the MIDI IN connector of the receiving (slave) device. To connect the Thomann DP-S 307 UP to a computer, you need a MIDI interface, sequencing or musical notation software, and two standard MIDI cables.
Diagram showing DP-S 307 UP connected to a computer via MIDI interface, sequencing software, and MIDI cables.
Connection to a Computer
The Thomann DP-S 307 UP includes both an onboard MIDI interface and an audio interface. Connect it directly to your computer without a special interface to use these functions.
Connections
Connecting to your computer is straightforward. Find the USB port on the rear of the Thomann DP-S 307 UP. Connect the provided USB cable (Type B) to the DP-S 307 UP and the other end (Type A) to a USB port on your computer.
Diagram illustrating the USB connection between the DP-S 307 UP and a computer.
Driver software installation
Visit www.asio4all.com and download the latest ASIO universal driver. Double-click the downloaded file, click "Next", and follow the on-screen instructions. This installation makes the DP-S 307 UP ASIO- and MIDI-compliant.
Screenshot of the ASIO4ALL 2.10 Setup Wizard, guiding users through installation.
How to Adjust Audio Settings
Windows
Configure sound and audio default devices via the system control panel. Settings may vary based on your specific audio configuration and installed software. Refer to Windows operating instructions for details. After setup, you can play the Thomann DP-S 307 UP while listening to audio files via Windows Media Player for practice.
Mac OS
After connecting the Thomann DP-S 307 UP, your Macintosh computer will detect it automatically. Configure it in "Audio MIDI setup" (found in Applications\Utilities). The DP-S 307 UP is fully compatible with Mac OSX's Core Audio drivers.
Connection to external audio equipment
Connect the Thomann DP-S 307 UP's LINE outputs to external audio equipment like power amplifiers, powered studio monitors, recorders, or Hi-Fi audio systems to listen to its sound. You can also record the DP-S 307 UP's sound using an external audio recorder. Connect an audio player to the DP-S 307 UP to listen to music through its speakers, or record the DP-S 307 UP's sounds from a computer's audio player.
Diagram showing LINE OUT/LINE IN connections from the DP-S 307 UP to external audio equipment like speakers and an audio recorder, with auxiliary inputs.
Technical Specifications
| Specification | Details |
|---|---|
| Cabinet | High-gloss ebony paint, Spruce sound board and ribs, Damping-system safety shutter |
| Keyboard | 88 piano Fatar hammer action keys, Sensitive velocity response |
| Polyphony | 64-note polyphony with effects |
| Tone-generating technology | Stereo PCM sampling |
| Speakers | Embedded Infrasonic Blow5 Studio Active Monitor technology, 180 W (80 W HF and 100 W LF), Full discrete power amplifiers with servo-loop and perfect protections, 2-way bass-reflex bi-amplified 5 inch near field, Flat frequency response (± 1.5 dB, 58 Hz to 20 kHz) and wide pass-band frequency (50 Hz to 22 kHz), 3/4-inch natural-silk dome high-frequency transducer, 5-inch polymer-coated paper-fiber cone low-frequency transducer |
| Sound programs | 8 realistic instrument voices (Piano, Jazz Trio, E.P1, E.P2, Organ1, Organ2, Strings, Pad) |
| Effects | FX source: MIC, LINE, SOUND; FX type: REVERB, CHORUS, ECHO; FX depth: LOW, MID, HIGH |
| Functions | Key transpose: ± 12 semitones; Touch control: 4 velocity curves (Soft, Mid, Heavy, Fix); Layer: Yes, Local Mode |
| Pedals | Sustain, soft, sostenuto |
| Controls | Master volume |
| Inputs/outputs | Wireless Audio interface; Headphones: 2 stereo standard 1/4-inch phone jacks; MIDI: Standard IN/OUT jacks; LINE IN/OUT: stereo RCA jacks; USB port: Type B |
| Audio interface | Built-in USB audio interface with ASIO driver for Windows® XP/VISTA/7 (32-bit and 64-bit) or later and Mac OS X (10.3 or later) |
| Dimensions (W × H × D) | 144 cm × 105.5 cm × 48 cm (56.7 in. × 41.5 in. × 18.9 in.) Diagram showing dimensions: 144 cm width, 105.5 cm height, 48 cm depth. |
| Weight | 115 kg (254 lbs) |
Protecting the Environment
Disposal of the packaging material
For transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed and are not within reach of babies and young children. Choking hazard! Do not dispose these materials with normal household waste; ensure they are fed to a recovery. Please follow the notes and markings on the packaging.
[♻️ Recycling Symbol]
Disposal of your old device
Electrical and electronic equipment often contain materials that can be unhealthy and environmentally harmful if not properly treated and disposed of. However, they are essential for proper operation. At the end of its operating lifetime, do not dispose of the device with normal household waste. This device is subject to the European directive 2002/96/EC. Dispose of this device through an approved waste disposal firm or your local waste facility. Comply with local rules and regulations when discarding the unit. If in doubt, consult your local waste disposal facility.
[♻️ Recycling Symbol]
