Ikon Smart One-Piece Smart Toilet Installation Manual

Important Safeguards

❗ DANGER: To reduce the risk of electrocution:

• Do not use while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not place in or drop into water or other liquid.
• Do not reach for a product that has fallen into water. Unplug immediately.
• Do not wash the main unit or electrical plug with water or detergent.
• Do not handle the electrical plug with wet hands.
• Never block the outlet of the air dryer.
• Never disassemble, repair or modify this product.
• During installation, disassembly, repair and maintenance of the product, the power plug must be switched off and water supply be shut off.

⚠️ WARNING: To reduce the risk of burns, electrocution, fire, or injury to persons.

• Close supervision is necessary when this product is used by, on, or near children or individuals with disabilities.
• Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
• Keep the cord away from heated surfaces.
• Never use while sleeping or drowsy.
• Never drop or insert any object into any opening or hose.
• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Connect this product to a properly grounded outlet only. See Grounding Instructions.
• Do not throw cigarettes and other burning materials into toilet, otherwise it might cause fire. This product is an electric appliance, so it must be placed far away from water and other liquids.
• Do not lay the product on its side or upside down during the electrical circuit.
• It is prohibited to use other electric appliances in the same socket.
• It is forbidden to use the power extension or unstable loose outlet.
• Do not reuse any existing water supply hoses, otherwise it might cause leakage, fire or electrical shock. Installation should include specified components and a new water supply hose.

? CAUTION: Indicates that failure to follow the instruction may cause body injury or property damage.

• Do not install or use the product in wet places like steam rooms etc.
• It is recommended to use a water-proof electrical outlet which should be installed in a place where it will not easily get wet.
• This product should be used with 110V-120V, 50/60Hz electrical current only, load current is at least 15A. Power plug must be equipped with a ground fault circuit interrupter or ground fault electrical leakage protector or similar high sensitive, rapid type leakage switch (Rated sensitive current under 6mA).
• When it thunders, it is strongly recommended to pull out the power plug.
• Do not stand on the ceramic toilet.
• Ceramic toilet must install floor fixing bolts.
• Do not stand on the product unit, seat and lid.
• Do not lean against the seat lid when using the product, to avoid damage.
• This product is equipped with a soft-closing seat lid. Do not push the toilet seat closed, or damage may occur.
• Do not use any caustic chemicals or scrubbing brush to clean this product.
• Exposure to direct sunlight is prohibited.
• Only use tap water or potable water, otherwise it may cause chafing.
• Do not connect water supply to heater outlet. Make sure inlet water temperature is between 3~35°C (37.4~95°F).
• When the room temperature is below zero degrees, please drain the water tank to avoid freezing.
• Raise room temperature to prevent the toilet from damage due to freezing.
• When moving the product from a cold or wet environment into normal room temperature, wait for 2 hours until the condensation water is fully volatilized. Doing so can prevent the product from electrical short-circuit.
• When not using the product for over three (3) days, drain the water out of the toilet and pull the electrical plug from the wall outlet.
• Stop using the product and shut off the power when the product malfunctions. Call for professional service.

Grounding Instructions

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

❗ DANGER: Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire. This product is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided -- if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel.

SAVE THESE INSTRUCTIONS

Technical Specifications

Main Unit

Cleaning device

Drying device

Heated seat

Deodorization

Other Features

Rated power: Under the condition of ambient temperature 23°C/73°F, water static pressure 0.18MPa±0.02MPa, water temperature 5°C/41°F, power toilet on, set water pressure, seat temperature, water temperature to the highest level in turn and perform one rear washing cycle.

List of Materials

• Main Unit: Ikon Smart One-Piece Smart Toilet
• Installation Manual
• Sealing Flange
• Angle Valve
• Mounting Kit
• Remote Controller
• Components Installation Cardboard
• Flange Braided Hose

Technical Drawing

Dimensions are provided for reference: Width approximately 390mm/15.4", Depth approximately 700mm/27.6", Height approximately 476mm/18.7". The drawing is for reference only, and the manufacturer reserves the right to modify the product appearance. Product appearance is subject to change in kind.

Parts Identification

Left side: Lid Button

Right side: Front washing, Spray nozzle, Nozzle shield, Dryer shield, Bumper, Seat, Ceramic toilet

Front: Remote control sensor, Approach the sensing area with foot (optional)

Toilet Installation

Precaution before installing

Minimum dynamic working water pressure: 0.09+MPa (3.96+Gal/min or 15+L/min). Failure to meet this pressure will not achieve the best flushing effect. Note: Apply the methods below if you don't have a water pressure testing device.

Water Volume Check: Open the angle valve to check the water volume. If the water volume after 10 seconds is greater than 0.66Gal (2.5L), then it is OK to proceed with installation.

Installation Steps

1. Installation of angle valve

Draw the drain outlet centerline on the floor. Install the angle valve at the proper position on the wall according to the dimensions of the toilet.

2. Cardboard installation

Align the cardboard with the centerline of the drain outlet. Draw the contour line according to the cardboard.

3. Hose

Connect the water inlet and angle valve of the toilet with the matching braided hose and tighten it.

4. Mounting bracket installation

Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.

5. Ceramic toilet installation

Install a sealing flange into the drain outlet. Install the ceramic toilet on the corresponding position, ensuring the toilet outlet sits perfectly on the drain outlet. Clean up the drain outlet before installation.

Note: Two people are required to carry the toilet.

6. Screw installation

Put the screw through the fixing sleeve and then install it through the holes (on both sides of the toilet ceramic) to the mounting bracket on the ground. Lock tight. Install the decorative cap on the fixing sleeve.

Preparation

1. Turn on the angle valve

Check the threaded connection for leaks to ensure complete sealing. Turn the angle valve counterclockwise to the full open position. (Note: The angle valve may require significant torque for the first time.)

2. Power Connection

Insert the leakage protection plug [GFCI plug] into a power socket, press the reset switch. The plug indicator lights up, indicating that the power is on.

Note: Press the TEST button prior to usage. The reset switch popping up indicates that the leakage protection function is normal. Press the TEST button (then RESET button) every month to assure proper operation.

WARNING: TEST BEFORE EACH USE. 1. PLUG INTO RECEPTACLE. 2. PRESS RESET BUTTON: VISUAL INDICATOR APPEARS. 3. PRESS TEST BUTTON: VISUAL INDICATOR DISAPPEARS. 4. PRESS RESET FOR USE. DO NOT USE IF ABOVE TEST FAILS.

3. Self-inspection

1. Once power is connected, the buzzer beeps, the button lights up in white, and the self-inspection starts.
2. The buzzer beeps again, then the self-inspection completes. The button lights up in white.
3. The product is ready to use.

Lid Automatic Open/Close

* Only for the product with lid auto opening/closing function. This function is turned off by default. For the first use, please turn on this function by remote control.

1. Approaching the toilet

When a user enters the sensing range, the seat lid opens automatically.

2. Leaving the toilet

The seat lid closes automatically 180 seconds after the user leaves.

3. Standing up to urinate

1. Open the seat by remote control or hand. 2. The seat and lid close automatically 180 seconds after the user leaves.

Foot Sensor

If the model you purchased has a foot sensor option:

1. Lid open

When the lid and seat are both closed, approach the sensing area with foot to open the lid. Sensing range is within 3±1cm.

2. Seat open

When the lid is open and the seat is closed, approach the sensing area with foot to open the seat. Sensing range is within 3±1cm.

3. Close seat and lid / Half flush

When the seat and lid are both open, approach the sensing area with foot to close the seat and lid and activate a half flush. Sensing range is within 3±1cm.

Maintenance

Main unit care and maintenance

• Shut off power supply before doing maintenance.
• Use only a soft, damp cloth to clean. Avoid using harsh chemicals.
• Once cleaning is completed and all surfaces are dry, reconnect the power plug.

Filter maintenance

If poor spray performance occurs under normal conditions:

1. Turn off power and the angle valve.
2. Unscrew angle valve nut.
3. Remove filter net.
4. Clean out the filter net under running water using a toothbrush.
5. Reinstall filter net and angle valve nut.
6. Turn on the angle valve and connect the power.

Spray nozzle maintenance and care

1. Nozzle self-cleaning

When no one is seated, short press the "REAR/MOVE" Button on the main unit; the nozzle will automatically stretch out to allow access for cleaning.

2. Spray nozzle disassembly

When the nozzle moves forward, the nozzle can be removed and cleaned separately.

3. Use only a soft cloth or soft brush to clean. Do not pull or push the wand, to avoid damage.

4. Nozzle retraction

Put the nozzle back on and press the "Stop" Button to return the spray wand to its normal position.

Emergency Troubleshooting

Power and water failure

Put around 2.1Gal (8L) water into a barrel and flush the ceramic bowl. Note: Avoid water spilling from the bowl.

Failure of remote control

1. Operate via buttons on the main unit.

2. Battery replacement: Remove the remote control from its holder. Open the battery cover and replace the batteries. Put the remote control back.

Note: After battery replacement, the remote control settings will be restored to the default. Please reset.

Product unused for a period of time

When the product is left unused for a long time, especially in cold weather, it is highly recommended to drain the water to prevent freezing.

To discharge water

1. Activate flushing, and then turn off the angle valve to stop water supply.
2. Unplug and cut off the electricity.
3. Disconnect the hose from the angle valve, drain the water, and reconnect.

Note: Before water discharging, the power must be cut off.

4. For your safety, it is recommended to put antifreeze into the remaining water in the bowl.

* Please turn on power and water supply when using again.

Description of the Button Function

1. Stop Button

1. Press and hold the Stop Button to enter shutdown mode (white light off). Press the Stop Button again to return to functional mode (white light always on). In shutdown mode, all functions and buttons (except the Stop Button) will not operate.

2. When seated, short press the Stop Button to stop front washing, rear washing, or drying functions. When no one is seated, repeatedly press the Stop Button; the main unit will switch between functional mode (white light always on) and energy saving mode (white light flashing).

2. Rear washing/ Oscillating washing

1. When seated, press the Rear Washing Button to start the rear washing function and press again to shift to oscillating washing. Press the Stop Button to stop rear washing immediately. After one cycle washing, the drying function will be automatically turned on and stop after one cycle.

2. When no one is seated, press the Rear Washing Button, the nozzle will stretch out to allow access for cleaning. Press Stop Button, the nozzle will retract.

3. Front washing/ Oscillating washing

When seated, press the Front Washing Button to start the front washing function and press again to shift to oscillating washing. Press the Stop Button to stop front washing immediately. After one cycle washing, the drying function will be automatically turned on and stop after one cycle.

4. Flushing

1. When seated, long press the Flushing Button to start the drying function. The drying will stop automatically after one cycle, while it will stop immediately if the user presses the Stop Button.

2. In non-off mode, short press the Flushing Button to start the flushing function. During rear washing or front washing, the flushing function will not operate. During nozzle cleaning, only when the spray wand is fully extended or retracted can the flushing function be activated.

Note: Default settings for all functions are intermediate when powering on. Use the remote control to switch to the function level set before.

Troubleshooting Guide

If the problem cannot be resolved as per above solutions, please disconnect the power and contact service providers.

⚠️ If the power leakage protection switch always trips, it means that the product is leaking. Please disconnect the power and contact service providers.

Warranty Terms

1. One-year limited warranty for commercial installation, and two-year limited warranty for residential installation.
2. Celite warrants its product to be free from defects in materials and workmanship during normal use when properly installed and serviced, for a period of one year for commercial or two years for residential from date of shipment. This limited warranty is only to the ORIGINAL PURCHASER of the products and is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the product. This warranty applies only to the Celite product purchased and installed in USA.
3. Celite's obligations under this warranty are limited to repair, replacement or other appropriate adjustment, at Celite's option, of the product or parts found to be defective in normal use, provided that such product was properly installed, used and serviced in accordance with instructions. Celite reserves the right to obtain necessary information including the claimed product to conduct investigation in order to determine the cause of the defect. Celite is not responsible for the cost of removal, return and/or reinstallation of the product.
4. This warranty does not apply to the following items:
   • Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.
   • Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, improper care or maintenance of the product.
   • Damage or loss resulting from sediments or foreign matter contained in a water system.
   • Damage or loss resulting from the quality of water in the region where the product is used.
   • Damage or loss resulting from improper installation or from installation of the product in a harsh and/or hazardous environment, or improper removal, repair or modification of the product. This includes locations where the water pressure is above local codes or standards.
   • Damage or loss resulting from electrical surges or lightning strikes or other acts which are not the fault of the manufacturer or which the product is not specified to tolerate, including failure to use the factory equipped cord and plug or use of a loose or faulty electrical outlet or use of a current or socket other than a 110V, 60Hz electrical current from a GFI (ground, fused) socket.
   • Damage or loss resulting from normal and customary wear and tear, such as gloss reduction, scratching or fading over time due to use, cleaning practices or water or atmospheric conditions, including but not limited to, the use of bleach, alkali, acid cleaners, dry (powder) cleaners or any other abrasive cleaners or the use of metal or nylon scrubbers.
5. If the warning label placed on the seat is broken or otherwise not intact, this limited warranty is void.
6. In order for this limited warranty to be valid, Celite needs to investigate each case. During this process, the customer needs to provide necessary information for Celite to investigate, including but not limited to photos or videos to demonstrate the reported issue, purchase order number, production date or tracking information coming with the product.
7. This warranty gives you specific legal rights. You may have other rights which vary from state to state, province to province or country to country.

⚠️ WARNING! Celite shall not be responsible or liable for any failure of, or damage to, this product caused by either chloramine in the treatment of public water supply or cleaners containing chlorine (calcium hypochlorite).

NOTE: The use of a high concentrate chlorine or chlorine related products can seriously damage the fittings. This damage can cause leakage and serious property damage.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY THE MANUFACTURER. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. THE MANUFACTURER SHALL NOT BE REPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. IN NO EVENT WILL THE MANUFACTURER'S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED.