Mini WiFi Camera Instruction Manual

1. Download and Install the APP

Scan the QR code using WeChat, a browser, or other applications to download and install the APP. Alternatively, search for "Linklemo" in the Apple Store, Google Play, or your mobile application store to download and install it.

(If QR code download fails, please search and download from the app store/Google Play)

2. APP Connection

1. Open the APP, register, and log in.
2. Open your mobile phone's settings and connect to Bluetooth.
3. Enter the network distribution mode: After turning on the machine, the green light will be on, and the blue light will flash quickly.
4. Click "Add Device" in the APP to automatically scan for the device. Once the device is scanned (P1), click to bind the device and proceed to the next step (P2). After successful addition, the blue indicator light will remain solid, and you can customize the device name (P3).

3. Product Structure

• 1. Lens
• 2. Working indicator light (green light): The green light is solid when powered on. It flashes slowly for 3 seconds before entering recording mode.
• 3. Battery indicator light (red light): The red light flashes when the battery is low. It remains solid when charging and turns off when fully charged.
• 4. WIFI status light (blue light): The blue light flashes when not connected to the phone and remains solid when connected.
• 5. Toggle switch: Toggle left or right to cut off the main power supply.
• 6. Type-C charging port: Supports 5V1A charging. Charging time is approximately 1.5-2 hours, and it can record for about 3 hours.
• 7. Reset hole: Press and hold the reset button to reset the machine if there are connection abnormalities or if recording is paused.
• 8. TF card port: Supports 8-64GB TF cards.
• 9. 6mm inch nut hole: Can be used to connect brackets, selfie sticks, etc.

* If the device cannot be added for a long time, press and hold the reset button for 5 seconds to re-enter the network configuration mode.

4. Precautions

• Ensure Bluetooth is enabled on your phone.
• Avoid installing the device on metal doors if possible.
• Since this device lacks a display screen and operation buttons, permissions must be set through the APP for normal use.
• Ensure the battery is sufficiently charged and the power is connected.
• After installation, remove the protective film from the lens before use.
• Turn off the power switch (labeled as 5 in the product structure diagram) when the device is not in use for extended periods.

FCC Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Quality Assurance

QC Pass: QC06

Inspection Date:

Product Model:

Purchase Date:

User Name:

Device Serial Number:

Purchase Price:

Contact Number:

Mailing Address:

Dealer Name:

Warranty Record:

Please fill in carefully and return with the warranted product to the dealer or contact the designated service provider for detailed troubleshooting.