4K HDR 8x8 Pure HDMI Matrix with Scaling Outputs, Audio De-embed & ARC
MX-0808-H2A-MK2 Quickstart Guide
Introduction
WyreStorm recommends reading through this document in its entirety to become familiar with the product's features prior to starting the installation process.
IMPORTANT! Installation Requirements
- Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
- While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
In the Box
- 1x MX-0808-H2A-MK2 Matrix
- 1x AC Power Cord (US/UK/EU/AU)
- 8x 3.5mm 5-Pin Terminal Block
- 1x 3.5mm 3-Pin Terminal Block
- 1x IR Remote (CR2025 Battery not Included)
- 2x Matrix Mounting Brackets with screws
- 1x Quickstart Guide (this document)
Basic Wiring Diagram
The diagram illustrates the basic setup for the WyreStorm MX-0808-H2A-MK2 matrix. It shows the unit connected to a Router via Ethernet for network access, enabling the built-in Web UI for configuration and control. An AC Mains power connection is also shown. Control System integration is depicted via RS-232 or Ethernet. The matrix connects to an Amplifier via digital or analog audio outputs. Sources are shown as HDR Sources connected to HDMI inputs, and displays are shown as 1080p Displays and HDR Displays connected to HDMI outputs. An Audio Return Channel (ARC) connection is also indicated.
KEY: Passive HDMI, Active HDMI, Ethernet, Digital Audio, Control, Power.
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends using pre-terminated HDMI due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
RS-232 Wiring
Most control systems and computers are DTE where pin 2 is RX; this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made.
| WyreStorm Connector | 3rd Party Device |
|---|---|
| Pin 1 TX (Transmit) | to RX (Receive) |
| Pin 2 RX (Receive) | to TX (Transmit) |
| Pin 3 G (Ground) | to G (Ground) |
Audio Wiring
This matrix contains audio connections for Digital Audio (Toslink). The connector uses a Tip for Audio Positive (+) and Shield for Audio Negative (-).
This matrix also contains audio connections for Analog Audio (5-pin Phoenix).
| WyreStorm Connector | 3rd Party Device |
|---|---|
| Pin 1 Left Positive (L+) | to Left Positive (L+) |
| Pin 2 Left Negative (L-) | to Left Negative (L-) |
| Pin 3 Ground (G) | to Ground (G) |
| Pin 4 Right Negative (R-) | to Right Negative (R-) |
| Pin 5 Right Positive (R+) | to Right Positive (R+) |
Setup and Configuration
Accessing the Web UI
This matrix uses an Auto IP method to generate the initial IP address based on network connections. By default, the IP address is set to DHCP and will pull the IP address from a connected DHCP server. Should the network not contain a DHCP server, the IP address will be generated based on the unit's MAC address. This operation occurs unless the IP Address setting in the Web UI is set to static.
- Connect the matrix to the same network as a PC.
- Using a 3rd party network scanner, scan the network for the IP address of the matrix.
- Open a web browser and enter the IP Address of the matrix.
- Enter the password for the matrix. Default Password: admin
IP Address Notes
- The IP address of the unit can be displayed by pressing and holding the UP and Down buttons on the front panel for 3 seconds. The IP address will be displayed on the front panel.
- The installer password and general password are the same by default. WyreStorm recommends changing the password for installer login to avoid any unwanted changes being made to the matrix configuration.
Low Power Mode (Standby)
This matrix contains a Low Power Mode that will place the unit into Standby, using less power than normal operating mode. While in this mode, the Front Panel display and LEDs will be Off, and outputs will be powered down. Once a command is sent via the Front Panel buttons, IR remote/control system, or RS-232/IP control system, the unit will wake from Standby and be fully operational. The unit can be placed back into standby via the Web UI or by sending an API command as described in the following sections.
Enabling Low Power Mode via Web UI
- Access the Web UI. Refer to Accessing the Web UI.
- Navigate to the Settings tab within the Admin section of the Web UI. Default password is admin.
- Under Low Power Mode, select On to enable.
Enabling via RS-232/IP
Refer to the product's API document for information on Com port and IP addressing settings.
- To place the unit into Standby, send the command STANDBY<CR><LF>.
- To remove the unit from Standby, send the command WAKE<CR><LF>.
- To query the current Standby state, send the command GET STANDBY<CR><LF>.
Troubleshooting
No or Poor-Quality Audio or Video (snow or noisy image)
- Verify that A/V mute is not enabled. Check Web UI for status on the selected output.
- Verify that the matrix is not in Standby. Refer to Low Power Mode (Standby) for details.
- Verify that power is being supplied to the source and receiving device and they are not in standby mode.
- Verify that all HDMI connections are not loose and are functioning properly.
- Verify that the output resolution of the source and display is supported by this matrix and receiver.
- If transmitting 3D or 4K, verify that suitable HDMI cables are being used.
No or Intermittent 3rd party Device Control
- Verify that the IR and RS-232 cables are properly terminated following the Wiring and Connections section.
- Change the matrix IR code set to avoid interference with other devices. Refer to IR Code Settings.
Troubleshooting Tips:
- WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
Specifications
| Parameter | Value |
|---|---|
| Audio and Video | |
| Inputs | 8x HDMI In: 19-pin type A |
| Outputs | 8x HDMI Out 19-pin HDMI type A 8x 5-pin Phoenix Balanced Analog Audio 8x Toslink Digital Audio |
| Video Encoding | Uncompressed 18Gbps |
| End to End Latency | None |
| Audio Formats | 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos |
| ARC | Supported |
| Video Resolutions (Max) | 1920x1080p @60Hz 16bit 3840x2160p @60Hz 10bit 4:2:2 HDR10/10+ 3840x2160p @60Hz 12bit 4:2:0 Dolby Vision 3840x2160p @50Hz 10bit 4:2:2 HLG 4096x2160p @60Hz 8bit 4:4:4 |
| Supported Standards | DCI | RGB | HDR10 | HDR10+ | Dolby Vision | HLG | BT.2021 |
| Maximum Pixel Clock | 600MHz |
| Communication and Control | |
| HDMI | HDMI 2.0 | HDCP 2.2 | EDID | CEC (display power trigger) |
| RS-232 | 1x 3-pin Phoenix for API control |
| LAN | 1x 8-pin RJ-45 for API control |
| Power | |
| Power Supply | 100V - 240V 50/60Hz AC |
| Max Power Consumption | 60W |
| Environmental | |
| Operating Temperature | 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing |
| Storage Temperature | -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing |
| Maximum BTU | 205 BTU/hr |
| Dimensions and Weight | |
| Rack Units/Wall Box | 1U |
| Height | 43.5mm/1.72in |
| Width | 440mm/17.33in |
| Depth | 300mm/11.82in |
| Weight | 3.58kg/7.88lbs |
| Regulatory | |
| Safety and Emission | CE | FCC | RoHS | RCM | EAC |
Note: WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.
