RYNOSKINRYNOSKIN
Installation Guide for RYNOSKIN models including: RS-FTH-001 Trailer Hitch 2 Receiver, RS-FTH-001, Trailer Hitch 2 Receiver, Hitch 2 Receiver, 2 Receiver, Receiver
RYNOSKIN Trailer Tow Hitch Receiver Fit 2021-2024 Ford Bronco 2 Door & 4 Door Class 3 Rear Trailer Hitch with 2" Square Receiver Heavy Textured Black : Automotive
File Info : application/pdf, 3 Pages, 397.68KB
DocumentDocument90-180min Installation time is different according to individual person. Cutting Not Required TRAILER HITCH 2" RECERIVER INSTALLATION INSTRUCTIONS PART NO. RS-FTH-001 Fits: 2021-2024 FORD BRONCO TOOLS REQUIRED WRENCH/SOCKET SET DO NOT OVER TORQUE. PLEASE FOLLOW THE TIGHTEN OPERATING LOAD STANDARD BELOW: 6mm BOLTS & NUTS: FROM 7 TO 8.5 FOOT POUND. 8mm BOLTS & NUTS: FROM 18 TO 20 FOOT POUND. 10mm BOLTS & NUTS: FROM 35 TO 40 FOOT POUND. 12mm BOLTS & NUTS: FROM 60 TO 70 FOOT POUND. Drilling Not Required PARTS LIST: Description Receiver Towing Hitch TO PROTECT YOUR INVESTMENT, DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES THAT COULD DAMAGE THE FINISH. MILD SOAP MAY BE USED TO CLEAN THE PRODUCTS. Qty Image 1 Remark Harness Bracket 1 12-1.75mm x 110mm Hex Bolts 4 12mm x 32mm x 3mm Flat Washers 8 12mm Nylon Lock Nuts 4 www.rynoskinauto.com Page 1 of 3 4/28/22 (LS) Receiver Hitch TRAILER HITCH 2" RECERIVER 2021-2024 FORD BRONCO 4-Pin Harness Bracket PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 1. Locate the mounting holes in the frame cross member behind the rear bumper, (Figure 1). 2. Carefully unwrap the Receiver Hitch. Line up the holes in the Hitch with the cross member. 3. Attach the Hitch to the cross member with the included (4) 12mm x 110mm Hex Bolts, (8) 12mm Flat Washers and (4) 12mm Nylon Lock Nuts, (Figures 2 & 3). NOTE: Insert the Hex Bolts from the front of the cross member through the back. Leave hardware loose at this time. 4. Select the 4-Pin Wire Harness Bracket, (Figure 2). Remove the Flat Washer and Lock Nut from the driver/left outer end of the Receiver Hitch. Slide the Harness Bracket over the end of the Hex Bolt, (Figures 2 & 4). Reuse the Flat Washer and Lock Nut to secure the Bracket to the Hitch. 5. Center and adjust the Receiver Hitch and fully tighten all hardware. 6. Attach the trailer harness to the Trailer Connection Tab, if installed, (Figure 5). 7. Do periodic inspections of the installation to make sure that all hardware is secure and tight. www.rynoskinauto.com Page 2 of 3 4/28/22 (LS) Rear (Fig 1) Mounting location on rear cross member (arrow) TRAILER HITCH 2" RECERIVER 2021-2024 FORD BRONCO (4) 12mm x 110mm Hex Bolts (8) 12mm Flat Washers (4) 12mm Nylon Lock Nuts Rear (Fig 2) Slide Hitch over cross member. Attach Harness Bracket to driver/left outer Hex Bolt (arrow) Rear Rear (Fig 3) Insert Hex Bolts from front facing side of Hitch and cross member (Fig 4) Attach Harness Bracket to driver/left outer Hex Bolt (arrow) (Fig 5) Receiver Hitch and Harness Bracket installed www.rynoskinauto.com Page 3 of 3 4/28/22 (LS)