AstroAI 100 PSI Portable Air Compressor User Manual

Introduction

Thank you for purchasing the 100 PSI Portable Air Compressor from AstroAI. This programmable air compressor features a digital display for monitoring air pressure during inflation. Once the preset pressure is reached, the air compressor automatically shuts off. For optimal performance and safety, users should read and follow all instructions before operating the device. This manual should be kept for future reference. For questions or concerns, AstroAI can be contacted at support@astroAl.com.

Product Compatibility & Usage Guidelines

• The air nozzle is compatible with all Schrader valves, making it suitable for cars, small trucks, SUVs, motorcycles, and bicycles.
• Included accessories are compatible with balls requiring a needle, air cushions, mattresses, and more.
• The pump is not intended for use with high-pressure or large-volume applications.
• Do not store the air compressor in high-temperature or humid environments.
• When not in use, disconnect the air compressor from all power sources.
• The air compressor may heat up during continuous use; caution should be exercised when handling it during or after use.
• Avoid extended and continuous use. The optimum time for continuous use is 15 minutes.
• After extended use, allow the pump to rest for 10 minutes.

Included Accessories

The AstroAI 100 PSI Portable Air Compressor comes with the following accessories:

1. Replacement Fuse
2. 2x Air Nozzle Cones
3. Needle Valve Adapter
4. Valve Extender
5. Easy-Connect Schrader Valve Adapter
6. 2x Rubber Mat

Diagram showing various accessories: a fuse, two conical nozzle adapters, a needle adapter, a valve extender, a Schrader valve adapter, and two rubber mats.

Operation Instructions

1. Start Vehicle's Engine: Before use, start the vehicle's engine. (Depiction of a car engine start/stop button).
2. Plug in Inflator Pump: Firmly plug the inflator pump into the car's 12V outlet to ensure a strong connection. (Depiction of a cigarette lighter plug).
3. Attach Air Nozzle: Remove the valve cap from the tire's valve stem, then attach the air nozzle to the valve stem. (Depiction of a tire valve stem with cap removed and nozzle attached).
4. Turn on Pump: Turn on the pump by pressing the inflation switch. (Depiction of a power switch with an 'I' for ON and 'O' for OFF).
5. Set Pressure Unit: Use the "M" button to set the desired pressure unit (e.g., PSI, KPA, Bar, KG/CM²). (Depiction of a control panel with 'M' button and other buttons).
6. Set Desired Pressure: Use the "+" and "-" buttons to set the desired pressure. Refer to the tire pressure guide inside the driver's door for guidance. Ensure the preset pressure is higher than the current pressure of the tire. The air compressor will inflate to the set pressure and automatically stop upon reaching it.
7. After Inflation: Once inflation is complete, turn off the inflation switch and disconnect the power cord from the 12V outlet. Unscrew the valve connector and place the tire valve cap back on the valve stem. (Depiction of a power switch with an 'I' for ON and 'O' for OFF).

Features

• Compatible with DC 12V, 10A cigarette lighters.
• LED Light for convenient use in dark environments.
• Pump stops inflating at preset pressure value.
• LED display is easy to read and understand.
• Portable design makes it convenient to carry.

Specifications

• Input Voltage: 12V DC
• Wire Length: 3 Meters
• Rated Power: 120W
• Cylinder Diameter: 22mm
• Max Pressure Reading: 100 PSI
• Display Units: PSI, KPA, Bar, KG/CM²
• Continuous Operating Time: 15 Minute Maximum

Troubleshooting

1. Air Compressor will not inflate

• Ensure the in-line fuse is securely inserted correctly; replace fuse if necessary.
• Check vehicle cigarette lighter fuse; it should be rated at 10A or higher.
• Ensure there is a strong connection with the power cord and 12V socket.
• If preset tire pressure is lower than current tire pressure, increase the preset tire pressure to the manufacturer recommended level.

2. Air Compressor is operating abnormally

• The inflation nozzle is not connected properly to the tire's valve stem.
• The 12V socket is not connected securely.
• If preset tire pressure is lower than current tire pressure, increase the preset tire pressure to the manufacturer recommended level.

3. Air leaking through hose

• Ensure there is a firm connection between the air nozzle and the tire valve.

4. Slow inflation

• The inflation nozzle is not connected properly to the tire's valve stem.
• Excessive use will slow the inflation rate of the pump. Allow it to cool for 10 minutes.

5. Shuts off after extended use

• If the air compressor continues to run for more than 15 minutes, it will shut off due to overheating protection. Allow it to cool for 10 minutes.

3 Year Limited Warranty

Each AstroAI Portable Air Compressor is free from defects in material and workmanship. This warranty does not cover damage resulting from neglect, misuse, contamination, alteration, accident, or abnormal conditions of operation or handling. This warranty covers the original purchaser only and is not transferable.

For questions or concerns, AstroAI is available to help at support@astroAl.com.

Diagram of Air Compressor Components

An illustration of the AstroAI 100 PSI Portable Air Compressor, showing its various parts with numbered labels:

1. Air Pressure Gauge
2. Carrying Handle
3. LED Light
4. Inflation Tube
5. LED Light Switch
6. Inflation Switch
7. Power Cord
8. 12V Cigarette Lighter Plug