PowerPoint Washing Machine Owner's Manual
Models: P35106MDW (6kg) and P35127MDW (7kg)
Safety Instructions ⚠️
Please read the following safety information thoroughly and follow it strictly to minimize the risk of fire or explosion, electric shock, and to prevent property damage, personal injury, or loss of life. Failing to follow these instructions shall void any warranty.
⚠️ Warning! This combination of symbol and signal word indicates a potentially dangerous situation which may result in death or serious injuries unless it's avoided.
ⓘ Caution! This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries or damage to property and the environment.
? Note! This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries.
⚠️ ELECTRIC SHOCK HAZARD
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
- If the machine is damaged, it must not be operated unless repaired by the manufacturer, its service agent, or similarly qualified persons. Risk of electric shock!
The appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children should be supervised that they do not play with the appliance.
- Children 3 years and under shall be kept away from the appliance or continuously supervised.
- Animals and children may climb into the machine. Check the machine before every operation.
- Do not climb or sit on the appliance.
INSTALLATION LOCATION AND SURROUNDING
- All washing and additional substances are to be kept in a safe place out of the reach of children.
- Do not install the machine on a carpet floor. The obstruction of the openings by a carpet can damage the machine.
- Keep the appliance clear from heating sources and direct sunlight to avoid plastic and rubber parts to corrode.
- Do not use the appliance in humid environments or rooms containing explosive or caustic gas. In case of water leakage or water splashes, let the appliance dry in the open air.
- The appliance must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the washing machine.
- Do not operate the machine in rooms with a temperature of below 5°C. This can cause damages to parts of it. If it is unavoidable, make sure to drain the water completely from the appliance after every use (see „Maintenance - Cleaning of drain pump filter") to avoid damages caused by frost.
- Never use flammable sprays or substances in the immediate proximity of the appliance.
INSTALLATION
- Remove all packaging material and transport bolts before using the appliance. Otherwise, serious damage may result.
- This appliance is equipped with a single inlet valve and can be connected to the cold water supply only.
- Mains plug must be accessible after installation.
- Before washing clothes for the first time, the product shall be operated once throughout all the procedures without any clothes inside.
- Before using the washing machine, the product shall be calibrated.
- Do not put any excessively heavy objects on the appliance, like water containers or heating devices.
- The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
- Max. Inlet water pressure 1 MPa. Min. inlet water pressure 0.05 MPa.
ELECTRICAL CONNECTION
- Make sure the supply cable is not trapped by the machine, it can get damaged.
- Connect the product to a grounded outlet protected by a fuse complying with the values in the "Technical specifications" table. The grounding installation has to be made by a qualified electrician. Ensure that the machine is installed in accordance with the local regulations.
- Water and electrical connections must be carried out by a qualified technician in accordance with the manufacturer's instructions and local safety regulations.
- Don't use multiple plugs or extension cords.
- The appliance must not have an external switching device such as a timer or connected to a circuit that is regularly switched on and off.
- Do not pull the plug out of the mains outlet if there is flammable gas around.
- Never pull out power plug with wet hands.
- Always pull at the plug, not at the cable.
- Always unplug the appliance if it is not being used.
⚠️ Warning!
WATER CONNECTIONS
- Check the connections of the water inlet tubes, the water tap and the outlet hose for possible problems due to changes of water pressure. If the connections loosen or leak, close the water tap and get it repaired. Do not use the appliance before the pipes and hoses are installed properly by qualified persons.
- Glass door may become very hot during the operation. Keep children and pets far away from the machine while it is operating.
- The water inlet and outlet hoses have to be safely installed and remain undamaged. Otherwise, water leakage can occur.
- Do not remove the drain pump filter while there is still water in the appliance. Big quantities of water can leak out, and there is a risk of scalding due to hot water.
OPERATION AND MAINTENANCE
- Never use any flammable, explosive or toxic solvents. Do not use gasoline and alcohol etc. as detergents. Only select detergents that are suitable for machine washing.
- Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooches, nails, screws, stones etc. may cause serious damages to this machine.
- Remove all objects from pockets such as lighters and matches before use the appliance.
- Thoroughly rinse items that have been washed by hand.
- Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, wax and wax removers should be washed in hot with an extra amount of detergent before being dried in the appliance.
- Items containing foam rubber (latex foam), shower caps, water proof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the machine.
- Fabric softeners or similar products should be used as recommended in their instructions.
- Never try to open the door forcefully. The door will unlock shortly after the end of a cycle.
- Please do not close the door with excessive force. If it is found difficult to close the door, please check if the clothes are properly inserted and distributed.
- Always unplug the appliance and close the water tap before cleaning and maintenance and after each use.
- Never pour water over the appliance for cleaning purpose. Risk of electric shock!
- Repairs shall only be carried out by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The producer will not be responsible for damages caused by the intervention of not authorized persons.
TRANSPORT
- Before Transport:
- Bolts shall be reinstalled to the machine by a specialized person.
- Accumulated water shall be drained out of the machine.
- This appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door cannot be used as a handle.
INTENDED USE
The product is intended only for home use and for textiles in household amounts suitable for machine washing and drying. This appliance is for indoor use only and not intended for built-in use. Only use according to these instructions. The appliance is not intended for commercial use.
Any other use is considered as improper use. The producer is not responsible for any damage or injuries that may result of it.
- This appliance is intended to be used in household and similar applications such as:
- Staff kitchen areas in shops, offices and other working environments;
- Farm houses;
- By clients in hotels, motels and other residential type environments;
- Bed and breakfast type environments;
- Areas for communal use in blocks of flats or in launderettes.
Packaging/Old appliance
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the collection systems or contact the retailer where the product was purchased. They return and can take this product for environmental safe recycling.
Installation
Product Description
Diagram showing the washing machine with labels: Top cover, Water supply hose, Detergent dispenser, Control panel, Power supply cord, Door, Drum, Service flap, Drain hose.
? Note! The product picture is for illustration only, please refer to real product as reference.
Accessories
- 4 x Cover caps
- 1 x Supply hose (cold water)
- 1 x Owner's manual
Installation area
⚠️ Warning!
- Stability is important to prevent the product from wandering! Make sure the machine is standing leveled and stable.
- Make sure that the product does not stand onto the power cord.
- Make sure to maintain the minimum distances from the walls as shown in the picture.
Before installing the machine, the location characterized as follows shall be selected:
- Rigid, dry, and level surface
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0°C
- Keep far away from the heat sources such as coal or gas burning appliances.
Unpacking the washing machine
⚠️ Warning!
- Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
- There is a risk of suffocation! Keep all packaging well away from children.
- Remove the cardboard box and styrofoam packing.
- Lift the washing machine and remove the base packaging. Make sure the small triangle foam (a) is removed with the bottom packaging together. If not, lay the unit down on the side surface and remove it manually.
- Remove the tape securing the power supply cord and drain hose.
- Remove the inlet hose from the drum.
Remove transport bolts
⚠️ Warning!
- You must remove the transport bolts from the backside before using the product.
Diagrams showing: Loosen the 4 transport bolts with a spanner. Remove the bolts including the rubber parts and keep them for future use. Close the holes using the cover caps.
Levelling the washing machine
⚠️ Warning!
- The lock nuts on all four feet must be screwed tightly against the housing.
- Loosen the lock nut.
- Turn the foot until it reaches the floor.
- Adjust the legs and lock the nuts with a spanner. Make sure the machine is level and steady.
Connect the water supply hose
⚠️ Warning!
- To prevent leakage or water damage, follow the instructions in this chapter.
- Do not kink, crush, or modify water inlet hose.
Diagrams showing connecting the water supply hose to the water inlet valve and a water tap with cold water.
? Note! Connect manually, do not use tools. Check if the connections are tight.
Drain Hose
⚠️ Warning!
- Do not kink or protract the drain hose.
- Position drain hose properly, otherwise damage might result of water leakage.
There are two ways to place the end of drain hose:
- Put it into the water trough.
- Connect it to the branch drain pipe of the trough.
Diagrams illustrating the two drain hose placement options.
Operation
Quick Start
ⓘ Caution!
- Before washing, please make sure the washing machine is installed properly.
- Your appliance was thoroughly checked before it left the factory. To remove any residual water and to neutralize potential odors, it's recommended to clean your appliance before first use. For this reason, start the Cotton program at 90°C without laundry and detergent.
1. Before Washing
Diagrams showing steps: Plug in (earth terminal, water tap), Open tap, Load, Close door, Add detergent (compartments I, II, III for Prewash, Main wash, Softener).
? Note! Detergent need to be added in compartment I if the pre-wash function is selected.
2. Washing
Diagrams showing steps: Select programme, Select function or remain default settings, Press Start/Pause to start the program.
3. After Washing
The door lock and the [Start / Pause] lights flash with the buzzer beeping or two small points flash on the digital screen.
Before Each Washing
- The ambient temperature of the washing machine should be 5-40°C. If used under 0°C, the inlet valve and draining system may be damaged. If the machine is installed under freezing conditions, it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose can unfreeze before use.
- Please check your laundry care labels and the detergent use instructions before wash. Use non-foaming or less-foaming detergent suitable for machine washing properly.
Diagrams showing steps for preparing laundry:
- Check the care label
- Sort laundry according to color and textile type
- Take all items out of the pockets
- Tie together long textile strips and belts, close zips and button
- Put small items into a laundry bag
- Turn easy-pilling and long-pile fabric inside out
⚠️ Warning!
- Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances like wax, oil, paint, gasoline, alcohol, kerosene, and other flammable materials.
- Washing single clothes items may easily create big eccentricity and cause alarm due to unbalance. Therefore it is suggested to add one or two more laundry items to the wash so that spin can be done smoothly.
Detergent Dispenser
Diagram of detergent dispenser with compartments I (Pre wash), II (Main wash), III (Softener), and a release button.
ⓘ Caution! Detergent only need to be added in "compartment I" after selecting pre-wash function.
Programme Table 1 (P35106MDW)
| Programme | I (Pre wash) | II (Main wash) | III (Softener) | Programme | I (Pre wash) | II (Main wash) | III (Softener) |
|---|---|---|---|---|---|---|---|
| Cotton 30 °C | ● | ● | ○ | Delicate 30 °C | ○ | ● | ○ |
| Cotton 40 °C | ● | ● | ○ | Delicate | ○ | ● | ○ |
| Cotton 60 °C | ● | ● | ○ | Ends in 9H | ○ | ● | ○ |
| Cotton 90 °C | ● | ● | ○ | Ends in 6H | ○ | ● | ○ |
| Synthetic | ○ | ● | ○ | Ends in 3H | ○ | ● | ○ |
| Synthetic 40 °C | ○ | ● | ○ | Quick Wash 45' | ○ | ● | ○ |
| Drum Clean | ○ | ● | ○ | Quick Wash 30' | ○ | ● | ○ |
| Cold Wash | ○ | ● | ○ | Quick Wash 15' | ○ | ● | ○ |
| Cold Wash 20 °C | ○ | ● | ○ | ECO 40-60 | ○ | ● | ○ |
| Spin Only | ○ | ○ | ○ | Cotton Intensive 40 °C | ○ | ● | ○ |
| Drain Only | ○ | ○ | ○ | Cotton Intensive 60 °C | ○ | ● | ○ |
| Rinse&Spin | ○ | ● | ○ |
● Means must, ○ Means optional
Detergent Recommendation
| Recommended washing detergent | Wash cycles | Washing temp. | Type of laundry and textile |
|---|---|---|---|
| Heavy-duty detergent with bleaching agents and optical brighteners | Cotton, ECO 40-60 | 30/40/60 | White laundry made from boil-proof cotton or linen |
| Colour detergent without bleaching agent and optical brighteners | Cotton, ECO40-60, Cold Wash | Cold/20/30/40 | Coloured laundry made from cotton or linen |
| Color or mild detergent without optical brighteners | Cold Wash, Synthetic | Cold/20/40 | Coloured laundry made from easy care fibres or synthetic materials |
| Mild washing detergent | Synthetic | Cold/40 | Delicate textiles, silk, viscose |
? Note!
- Agglomerating or ropy detergent or additive can be diluted in some water before pouring it into the detergent dispenser, to avoid its inlet to get blocked and thus cause a water overflow.
- Please choose the suitable type of detergent to get a maximum of washing performance and a minimum of water and energy consumption.
- To achieve the best cleaning result, a proper detergent dosing is important.
- Use a reduced detergent amount if the drum is not filled completely.
- Always adjust the amount of detergent to the water hardness; if your tap water is soft, use less detergent.
- Dose according to how dirty your laundry is; less dirty clothes require less detergent.
- Highly concentrated (compact detergent) requires particularly accurate dosing.
Following symptoms are a sign of detergent overdosing:
- Heavy foam formation
- Poor washing and rinsing result
Following symptoms are a sign of detergent underdosing:
- Laundry turns grey
- Built-up of limescale deposits on the drum, the heating element and/or the laundry
Control Panel
Diagram of the control panel with numbered buttons and a program selector dial. Labels include: On/Off (1), Start/Pause (2), Option (3), Programmes (4), Display (5). Program names are listed around the dial: Quick Wash 15', 30', 45', Ends in H, Mix 6H, 40°C, 9H, Delicate 30°C, Rinse&Spin, Drain Only, Spin Only, OFF, Drum Clean, Synthetic 40°C, Cold Wash, Cold Wash 20°C, Cotton 30°C, 40°C, 60°C, 90°C, Prewash, Extra Rinse, No Spin, Cotton Intensive 40°C, Cotton Intensive 60°C, ECO 40-60.
- 1 On/Off: Turn the appliance on and off.
- 2 Start/Pause: Start or pause your programme.
- 3 Option: This allows you to select additional functions and will light when selected.
- 4 Programmes: Available according to the laundry type.
- 5 Display: The display shows settings, estimated remaining time, options, and status messages.
Programmes (P35106MDW)
| Programme | Load(kg) | Display Time |
|---|---|---|
| Synthetic | 6.0 | 6.0 |
| Synthetic 40°C | 3.0 | 2:20 |
| Cold Wash | 3.0 | 2:20 |
| Cold Wash 20 °C | 6.0 | 1:00 |
| Cotton 30 °C | 6.0 | 1:01 |
| Cotton 40 °C | 6.0 | 2:40 |
| Cotton 60 °C | 6.0 | 2:40 |
| Cotton 90 °C | 6.0 | 2:45 |
| ECO 40-60 | 6.0 | 2:50 |
| Cotton Intensive 40 °C | 6.0 | 3:16 |
| Cotton Intensive 60°C | 6.0 | 4:04 |
| Drum Clean | - | 4:08 |
| Spin Only | 6.0 | 1:18 |
| Drain Only | - | 0:12 |
| Rinse&Spin | 6.0 | 0:01 |
| Delicate 30°C | 2.5 | 0:20 |
| Delicate | 2.5 | 0:50 |
| Ends in 9H | 6.0 | 0:48 |
| Ends in 6H | 6.0 | 0:59 |
| Ends in 3H | 6.0 | 0:59 |
| Quick Wash 45′ | 2.0 | 0:59 |
| Quick Wash 30′ | 2.0 | 0:45 |
| Quick Wash 15' | 2.0 | 0:30 |
| 0:15 |
? Note! The parameters in this table are only for user's reference. The actual parameters maybe different with the parameters in above mentioned table.
Programmes (P35106MDW - Technical Data)
| Cycle | Nominal capacity in kg | Cycle duration in h:min | Energy consumption in KWh/cycle | Water consumption in L/cycle | Highest washing temperature °C 1) | Residual moisture in % / Spin speed in rpm 2) |
|---|---|---|---|---|---|---|
| Cold Wash 20°C | 3.0 | 1:01 | 0.207 | 37 | 20 | 65%/1000 |
| Cotton 60°C | 6.0 | 2:45 | 1.280 | 58 | 60 | 70%/800 |
| Synthetic | 3.0 | 2:20 | 0.327 | 55 | Cold | 65%/1000 |
| Quick Wash 15' | 2.0 | 0:15 | 0.035 | 32 | Cold | 75%/800 |
| Cotton Intensive 40°C | 6.0 | 4:12 | 1.085 | 58 | 40 | 65%/1000 |
| ECO 40-60 3) | 6.0 | 3:18 | 1.000 | 50.0 | 41 | 62% / 1000 |
| 3.0 | 2:36 | 0.650 | 39.0 | 33 | 62% / 1000 | |
| 1.5 | 2:36 | 0.360 | 36.0 | 20 | 62% / 1000 |
Notes on table: Data is for reference only, may change. Values for programmes other than ECO 40-60 are indicative. New EU energy efficiency class E. Energy test program: ECO 40-60. Half load for 6.0Kg machine: 3.0Kg. Quarter load for 6.0Kg machine: 1.5Kg. Old EU energy efficiency class A+.
Programmes (P35127MDW)
| Programme | Load(kg) | Display Time |
|---|---|---|
| Synthetic | 7.0 | 7.0 |
| Synthetic 40°C | 3.5 | 2:20 |
| Cold Wash | 3.5 | 2:20 |
| Cold Wash 20 °C | 7.0 | 1:00 |
| Cotton 30 °C | 7.0 | 1:01 |
| Cotton 40 °C | 7.0 | 2:40 |
| Cotton 60 °C | 7.0 | 2:40 |
| Cotton 90 °C | 7.0 | 2:45 |
| ECO 40-60 | 7.0 | 2:50 |
| Cotton Intensive 40 °C | 7.0 | 3:28 |
| Cotton Intensive 60°C | 7.0 | 3:48 |
| Drum Clean | - | 3:53 |
| Spin Only | 7.0 | 1:18 |
| Drain Only | - | 0:12 |
| Rinse&Spin | 7.0 | 0:01 |
| Delicate 30°C | 2.5 | 0:20 |
| Delicate | 2.5 | 0:50 |
| Ends in 9H | 7.0 | 0:48 |
| Ends in 6H | 7.0 | 0:59 |
| Ends in 3H | 7.0 | 0:59 |
| Quick Wash 45′ | 2.0 | 0:59 |
| Quick Wash 30′ | 2.0 | 0:45 |
| Quick Wash 15' | 2.0 | 0:30 |
| 0:15 |
? Note! The parameters in this table are only for user's reference. The actual parameters may be different with the parameters in above mentioned table.
Programmes (P35127MDW - Technical Data)
| Cycle | Nominal capacity in kg | Cycle duration in h:min | Energy consumption in KWh/cycle | Water consumption in L/cycle | Highest washing temperature °C 1) | Residual moisture in % / Spin speed in rpm 2) |
|---|---|---|---|---|---|---|
| Cold Wash 20°C | 3.5 | 1:01 | 0.213 | 41 | 20 | 60%/1200 |
| Cotton 60°C | 7.0 | 2:45 | 1.385 | 65 | 60 | 60%/1200 |
| Synthetic | 3.5 | 2:20 | 0.327 | 60 | Cold | 60%/1200 |
| Quick Wash 15' | 2.0 | 0:15 | 0.035 | 34 | Cold | 75%/800 |
| Cotton Intensive 40°C | 7.0 | 3:48 | 1.088 | 65 | 40 | 60%/1200 |
| ECO 40-60 3) | 7.0 | 3:28 | 0.940 | 55.3 | 39 | 62%/1200 |
| 3.5 | 2:42 | 0.590 | 41.5 | 35 | 62%/1200 | |
| 2.0 | 2:42 | 0.435 | 35.6 | 30 | 62%/1200 |
Notes on table: Data is for reference only, may change. Values for programmes other than ECO 40-60 are indicative. New EU energy efficiency class D. Energy test program: ECO 40-60. Half load for 7.0Kg machine: 3.5Kg. Quarter load for 7.0Kg machine: 2.0Kg.
Explanation of terms:
- The highest temperature reached by the laundry in the wash cycle for at least 5 minutes.
- Residual moisture after the wash cycle in water content percent and the spin speed at which this was achieved.
- The ECO 40-60 programme is able to clean normally soiled cotton laundry declared to be washable at 40°C or 60°C, together in the same cycle. This programme is used to assess the compliance with the regulation (EU) 2019/2023.
The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration.
Loading the household washing machine up to the capacity indicated for the respective programmes will contribute to energy and water savings.
Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
ⓘ Caution! If there is any break in the power supply while the machine is operating, a special memory stores the selected programme. The machine will continue the programme when the power supply is re-established.
Programmes Descriptions
| Programmes | Description |
|---|---|
| Synthetic | Wash synthetic articles, for example: shirts, coats, blending. While washing the knitting textiles, detergent quantity shall be reduced due to its loose string construction and easily forming bubbles. |
| Delicate | For delicate, washable textiles, e.g. made of silk, satin, synthetic fibres or blended fabrics. |
| Drum Clean | It applys 90 °C high temperature sterilization to make the clothes washing more green. When this procedure is performed, the clothes or other washing cannot be added. When proper amount of chlorine bleaching agent is put in, the barrel cleaning effect will be better. The customer can use this programme regularly according to the need. |
| Spin Only | Extra spin with selectable spin speed. |
| Rinse&Spin | Extra rinse with spin. |
| Drain Only | Drain off the water. |
| Quick Wash 15' | It is suitable for washing few and not very dirty clothes quickly. |
| Cotton Intensive | To increase the washing effects, washing time is increased. |
| ECO 40-60 | Default 40°C, not selectable, suitable for laundry washing at about 40°C-60°C. |
| Cold Wash | Cold water to wash clothes. |
| Cotton | Hard-wearing textiles, heat-resistant textiles made of cotton or linen. |
| Ends in | The function can be set with this programme, the total time including washing time and delaying time is 3h, 6h or 9h. |
Option
| Cycle | Default Temp.(°C) | Load(kg) | Additional functions | |||
|---|---|---|---|---|---|---|
| 5.0 | 6.0 | 7.0 | 8.0 | |||
| Synthetic | Cold | 2.5 | 3.0 | 3.5 | 4.0 | Pre Wash, Extra Rinse |
| Synthetic 40°C | 40 | 2.5 | 3.0 | 3.5 | 4.0 | Pre Wash, Extra Rinse |
| Cold Wash | Cold | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| Cold Wash 20 °C | 20 | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| Cotton 30°C | 30 | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| Cotton 40 °C | 40 | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| Cotton 60 °C | 60 | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| Cotton 90 °C | 90 | 5.0 | 6.0 | 7.0 | 8.0 | Pre Wash, Extra Rinse |
| ECO 40-60 | 60 | 5.0 | 6.0 | 7.0 | 8.0 | |
| Cotton Intensive 40 °C | 40 | 5.0 | 6.0 | 7.0 | 8.0 | |
| Cotton Intensive 60°C | 60 | 5.0 | 6.0 | 7.0 | 8.0 | |
| Drum Clean | 90 | - | - | - | - | |
| Spin Only | 5.0 | 6.0 | 7.0 | 8.0 | ||
| Drain Only | - | - | - | - | - | |
| Rinse&Spin | 5.0 | 6.0 | 7.0 | 8.0 | Extra Rinse | |
| Delicate 30 °C | 30 | 2.5 | 2.5 | 2.5 | 2.5 | Extra Rinse |
| Delicate | Cold | 2.5 | 2.5 | 2.5 | 2.5 | Extra Rinse |
| Ends in 3H/6H/9H | 40 | 5.0 | 6.0 | 7.0 | 8.0 | Delay |
| Quick Wash 45′ | 40 | 2.0 | 2.0 | 2.0 | 2.0 | |
| Quick Wash 30′ | 30 | 2.0 | 2.0 | 2.0 | 2.0 | |
| Quick Wash 15' | Cold | 2.0 | 2.0 | 2.0 | 2.0 |
? Note! For the maximum spin speed, program time, and other details of the ECO 40-60 program, please refer to the content on the Product Fiche page. The table shows which cycle offers which options for adjustment. If an adjustment is not possible for a cycle.
Functions
Prewash
The Prewash function can get an extra wash before main wash, it is suitable for washing the dust rises to surface of the clothes; You need to put detergent into the Case (I) when select it.
Extra Rinse
The laundry will undergo extra rinse once after you select it.
No Spin
It will not spin if you choose this function.
Mute the buzzer
Diagram: Choose the Programme → Press [Prewash] button for 3 sec. → Buzzer is mute. To activate the buzzer function, press the button again for 3 seconds. The setting will be kept until the next reset.
ⓘ Caution! After Muting the buzzer function, the sounds will not be activated any more.
Child Lock
To avoid misoperation by children.
Diagram: Choose the Programme → Start → Press [Extra Rinse] and [No Spin] 3 sec. till buzzer beep.
ⓘ Caution!
- Only press and hold the two buttons can release “Child Lock”, even power off, switch off, and program end, the “Child Lock” will lock all buttons except power button and “Child Lock” button.
- Please release “Child Lock” before selecting program and starting washing.
Maintenance
Cleaning and Care
⚠️ Warning!
- Always unplug the appliance and close the water tap before cleaning and maintenance.
Cleaning the Cabinet
Proper maintenance on the washing machine can extend its working life. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use a cloth to wipe it off immediately. Never use sharp items to clean the appliance.
ⓘ Caution!
- Never use abrasive or caustic agents, formic acids or its diluted solvents or similar substances, like alcohol or chemical products.
Cleaning the Drum
Any rust stains left inside the drum by metal articles must be removed immediately using chlorine-free detergents. Never use steel wool for cleaning the drum!
? Note! Keep any laundry away from the machine while cleaning the drum.
Cleaning the Door Seal and Glass
Wipe the glass and seal after each wash to remove lint and stains. If lint builds up, it can cause leakages. Remove any coins, buttons, and other objects from the seal after each wash. Clean the Door Seal and Glass every month to ensure the normal operation of the appliance.
Cleaning the Inlet Filter
? Note! Diminishing water flow is a sign that the filter need to be cleaned.
- Close the tap and remove the water supply hose from it.
- Clean the filter with a brush.
- Unscrew the water supply hose from the backside of the machine. Pull out the filter with long nose pliers.
- Use a brush to clean the filter.
- Reinstall the filter to the water inlet and reconnect the water supply hose.
- Clean the Inlet filter every 3 months to ensure the normal operation of the appliance.
Diagrams showing filter cleaning steps.
Clean The Detergent Dispenser
- Press down the release [ ? ] on the softener cover and pull the dispenser drawer out of the recess. Clean the inside of the recess with a brush.
- Lift the softener cover off the dispenser drawer and wash both items with water.
- Restore the softener cover and push the drawer back into the recess.
Diagrams showing dispenser cleaning steps.
? Note!
- Do not use abrasive or caustic agents to clean plastic parts.
- Clean the detergent dispenser every 3 months to ensure the normal operation of the appliance.
Cleaning the Drain Pump Filter
⚠️ Warning!
- Make sure that the machine has finished the washing cycle and is empty. Switch it off and unplug it before cleaning the drain pump filter.
- Be careful of hot water. Allow the water to cool down. Risk of scalding!
- Clean the filter periodically every 3 months to ensure the normal operation of the appliance.
Diagrams showing drain pump filter cleaning steps: Open the lower cover cap, Open the filter by turning to the counter clockwise, Remove extraneous matter, Close the lower cover cap.
ⓘ Caution! When the appliance is in use and depending on the programme selected, there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.
Trouble Shooting
Whenever there is a problem with the appliance, check if you can solve it following the tables below. If the problem persists, please contact the customer service.
| Description | Possible cause | Solution |
|---|---|---|
| Appliance does not start | Door is not closed properly. Clothes are stuck. | Close the door properly and restart. Check the laundry. |
| Door can't be opened | Safety protection is activated. | Disconnect the power and restart. |
| Water leakage | Connections are not tight enough. | Check and fasten the water inlet pipe. Check and clean the outlet hose. |
| Detergent residues in the detergent dispenser | Detergent is damp and/or clotted. | Clean and wipe the detergent dispenser dry. |
| Indicator or display does not work | PC board or harness have connection problems. | Switch off the power and check if the mains plug is connected properly. |
| Abnormal noise | Fixing bolts still in place. Floor is not solid or level. | Check if the fixing bolts have been removed. Make sure the appliance is installed on a solid and level floor. |
Error Codes
| Description | Reason | Solution |
|---|---|---|
| Door is not closed properly | Prewash Off / Off / Off Off | Restart after the door is closed. Check if the clothes is stuck. |
| Water injecting problem while washing | Extra Rinse Off / Off / Flash | Check if the water pressure is too low. Straighten the water pipe. Check if the inlet valve filter is blocked. |
| Overtime water draining | No Spin Off / Flash / Flash Off | Check if the drain hose is blocked. |
| Water overflow | Pause/Start Flash / Off / Off Off | Restart the washer. |
| Others | Off / Off / Off Off | Please try again first, call up service line if there are still troubles. |
Customer Service & Technical Specifications
Customer Service
Spare parts for your appliance are available for a minimum of 10 years. In case of questions, please contact our customer service at:
⚠️ Warning! Risk of electric shock
- Never try to repair an appliance which is defective or presumed to be defective. You may put your own and future users' lives in danger. Only authorized specialists are allowed to carry out this repair work.
- Improper repair will void the warranty and subsequent damages can't be recognized!
Transport
IMPORTANT STEPS WHEN MOVING THE APPLIANCE
- Unplug the appliance and close the water inlet tap.
- Check if the door and the detergent dispenser are closed properly.
- Remove the water inlet pipe and the outlet hose from the house installations.
- Let the water drain completely from the appliance (see “Maintenance Cleaning the drain pump filter”).
- Important: Re-install the 4 transport bolts in the back of the appliance.
- This appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door cannot be used as a handle.
Technical Specifications
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Power Supply | 220-240V~50Hz | Height | 85 |
| MAX.Current | 10A | Dimensions in cm (W*D*H) | Width: 60 |
| Standard Water Pressure | 0.05MPa~1MPa | Depth: 40 |
Model P35106MDW
| Model | Washing Capacity | Dimension (W*D*Hmm) | Net Weight | Rated Power |
|---|---|---|---|---|
| P35106MDW | 6.0kg | 595*400*850 | 52kg | 2000W |
Model P35127MDW
| Model | Washing Capacity | Dimension (W*D*Hmm) | Net Weight | Rated Power |
|---|---|---|---|---|
| P35127MDW | 7.0kg | 595*400*850 | 53kg | 2050W |
General Product Parameters (P35106MDW)
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Rated capacity (kg) | 6.0 | Dimensions in cm (W*D*H) | Height: 85 |
| Width: 60 | |||
| Depth: 40 | |||
| Energy efficiency index (EEIW) | 91.0 | Energy efficiency class (E) | E |
| Washing efficiency index (c) | 1.031 | Rinsing effectiveness (g/kg) (c) | 5.0 |
| Energy consumption in kWh per cycle, based on the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used. | 0.737 | Water consumption in litre per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water. | 43 |
| Maximum temperature inside the treated textile (°C) | Rated capacity: 41 Half: 33 Quarter: 20 | Weighted remaining moisture content (%) (%) | 62.9 |
| Spin speed (rpm) | Rated capacity: 1000 Half: 1000 Quarter: 1000 | Spin-drying efficiency class (c) | C |
| Programme duration (h:min) | Rated capacity: 3:18 Half: 2:36 Quarter: 2:36 | Type | free-standing |
| Airborne acoustical noise emissions in the spinning phase (dB(A) re 1 pW) | 80 | Airborne acoustical noise emission class (c) (spinning phase) | C |
| Off-mode (W) (if applicable) | 0.50 | Standby mode (W) (if applicable) | 1.00 |
| Delay start (W) (if applicable) | 4.00 | Networked standby (W) (if applicable) | N/A |
| Minimum duration of the guarantee offered by the supplier (*)(*) | |||
| This product has been designed to release silver ions during the washing cycle | NO |
Additional Information: Weblink to the supplier's website, where the information in point 9 of Annex II to Commission Regulation (EU) 2019/2023 (1) is found: [Link placeholder]
General Product Parameters (P35127MDW)
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Rated capacity (kg) | 7.0 | Dimensions in cm (W*D*H) | Height: 85 |
| Width: 60 | |||
| Depth: 40 | |||
| Energy efficiency index (EEIW) | 80.0 | Energy efficiency class (E) | D |
| Washing efficiency index (c) | 1.031 | Rinsing effectiveness (g/kg) (c) | 5.0 |
| Energy consumption in kWh per cycle, based on the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used. | 0.690 | Water consumption in litre per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water. | 45 |
| Maximum temperature inside the treated textile (°C) | Rated capacity: 39 Half: 35 Quarter: 30 | Weighted remaining moisture content (%) (%) | 62.9 |
| Spin speed (rpm) | Rated capacity: 1200 Half: 1200 Quarter: 1200 | Spin-drying efficiency class (c) | C |
| Programme duration (h:min) | Rated capacity: 3:28 Half: 2:42 Quarter: 2:42 | Type | free-standing |
| Airborne acoustical noise emissions in the spinning phase (dB(A) re 1 pW) | 80 | Airborne acoustical noise emission class (c) (spinning phase) | C |
| Off-mode (W) (if applicable) | 0.50 | Standby mode (W) (if applicable) | 1.00 |
| Delay start (W) (if applicable) | 4.00 | Networked standby (W) (if applicable) | N/A |
| Minimum duration of the guarantee offered by the supplier (*)(*) | |||
| This product has been designed to release silver ions during the washing cycle | NO |
Additional Information: Weblink to the supplier's website, where the information in point 9 of Annex II to Commission Regulation (EU) 2019/2023 (1) is found: https://eprel.ec.europe.eu
1) The actual energy consumption will depend on how the appliance is used.
2) The actual water consumption will depend on how the appliance is used and on the hardness of the water.
3) Delivery of the spare parts within 15 working days after having received the order.
Product Data Sheet concerning (EU) 2019/2014
The product data sheet for your appliance can be found online. Go to https://eprel.ec.europe.eu and enter the model identifier for your appliance to download the data sheet. The model identifier for your appliance can be found in the technical specifications section.
