WORKPRO 60" Heavy-Duty Adjustable Workbench

Safety Information

To reduce the risk of serious injury, read and follow the safety instructions below before assembling and using this product.

1. Intended Use: This product is intended for indoor use only.

2. Usage Restriction: This product is not designed for commercial nor industrial usage.

CAUTION!

• Check all nuts and bolts periodically for tightness. When required, tighten them.
• DO NOT leave children unattended near this product.
• Keep the product on level surfaces. The product could become unstable and it may tip over if stored or moved on an uneven surface, which may cause personal injury, death or product damage.
• DO NOT alter this product in any manner. For example, do not weld external bar locks or attach electrical equipment. This may cause product damage or personal injury.
• Any assembly or maintenance of the product must be carried out by adults only.
• Use at least two people to move, assemble or install this workbench. Failure to do so can result in personal injury or product damage.
• DO NOT stand on the product and do not use it as scaffold.

3. Extension Cord:

• Only use a three-wire extension cord with all three prongs intact. Never remove the round grounding prong.
• Extension cord must be connected to a 125Volt GFCI protected outlet with proper ground. If GFCI outlet is not available, use an extension cord with GFCI protection built in.
• Check the insulation and plugs of extension cord before using. DO NOT use cord if it is worn or damaged.
• DO NOT overload extension cord.
• DO NOT connect extension cord to outlet that also supplies critical safety equipment with power.
• Make sure the power supply cord is unplugged before any servicing or cleaning.

4. Electrical Shock Hazard:

• Do not plug cord into outlet with wet hands.
• Do not use this workbench near a bathtub, a shower, or a swimming pool.
• Workbench plugs must match the outlet.
• Never modify the plug in any way. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces. There is an increased risk of electric shock if your body is earthed or grounded.

5. FCC Compliance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

"Please note that changes or modifications of this product are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment."

ℹ️ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specifications

Package Contents

Ensure all components are present. If any components are missing, do not proceed with assembly. Please send an email to service@greatstartools.com or call 877-876-7562.

Diagram Description:

The workbench consists of two leg assemblies (A and B), two beams (C), a rubber wood top (D), and a table stiffener (E). Fasteners include #5x15 Phillips head self-tapping screws (AA) and M8x20 inner hexagonal head bolts (BB). A hook is also present on one leg assembly.

Parts List:

Tools Required (Not Included):

• Electric Drill
• PH2 Screwdriver
• 13mm Combination Spanner
• 19mm Combination Spanner
• 5mm Hex Key

Assembly Instructions

General Notes:

ℹ️ NOTE: Do not tighten all the screws before step 4.

ℹ️ NOTE: Assemble on a flat surface. A piece of cardboard is recommended to keep the product from being scratched during assembly.

Step 1: Attach the beams

Attach the leg (A) and leg (B) to beams (C) with 8 pcs M8 x 20 inner hexagonal head bolts (BB).

Diagram Description: Two leg assemblies (A and B) are connected to two beams (C) using M8x20 bolts (BB). The diagram shows the orientation of parts.

Step 2: Attach the rubber wood top

Place rubber wood top (D) facing down on a flat surface with positioning labels facing upward. Use soft moving blanket or packaging material to protect the top during assembly.

Align the legs with the corresponding positioning labels and install the legs (A&B) & beams (C) on the rubber wood top (D) using 24 pcs #5x15 Phillips head self tapping screws (AA).

ℹ️ NOTE: Since the wood is hard, an electric drill is recommended when assembling.

ℹ️ NOTE: We recommend that the leg with power strip is assembled close to the side of the brand "WORKPRO". However, you can adjust the assembly position of the leg with power strip as you need.

Diagram Description: The rubber wood top (D) is placed upside down. The leg assemblies (A, B) and beams (C) are attached to the underside of the top (D) using #5x15 screws (AA). Positioning labels on the top indicate alignment points. The diagram also notes not to install screws for the table stiffener (E) yet.

Step 3: Attach the table stiffener

Attach the table stiffener (E) to rubber wood top (D) with 6 pcs #5x15 Phillips head self tapping screws (AA).

Diagram Description: The table stiffener (E) is attached to the underside of the rubber wood top (D) using #5x15 screws (AA).

Step 4: Adjust the height of workbench

Adjust the position of screws by the PH2 screwdriver and 13mm combination spanner to acquire suitable height.

ℹ️ NOTE: Adjust height of table range is from 31 ½"–39 ¾".

Diagram Description: Two diagrams show the adjustable legs. One leg is shown being adjusted upwards, and the other shows a locked position. A screwdriver and spanner are depicted.

Step 5: Adjust the level of workbench

Easily leveled with its height-adjustable leg pads. Rotate the pad to the suitable position and lock with the corresponding nuts(M12) by the 19mm combination spanner.

Diagram Description: Two diagrams illustrate adjusting the leg pads. The left shows rotating the pad upwards (rise up ⬆️), and the right shows locking the nut (lock nut ?). A 19mm spanner is implied.

Step 6: Placement of power plug

The power plug and cord are hung on the hook.

Diagram Description: A diagram shows the power cord and plug being hung on a hook attached to the workbench frame.

Power Strip Removal

ℹ️ NOTE: We strongly recommend DO NOT remove the power strip. If you need to remove for any reason, you can do as follows.

Unscrew 1 pc M4*10 phillips flange bolt (1), 1 pc M4 flat washer (2), and 1 pc M4 hexagon nut (4). Push the power strip (1) in the right direction and take it out.

Diagram Description: A diagram shows the underside of the workbench where the power strip is mounted. It indicates unscrewing a bolt (1), a washer (2), and a nut (4) to remove the power strip (labeled 1 in the diagram, but this seems to be a typo in the original OCR, it should refer to the power strip assembly). The diagram shows the power strip being pushed out.

Parts for Removal:

Maintenance

• Check all nuts and bolts periodically for tightness. When required, tighten them.

Care and Cleaning

Periodically clean the workbench surfaces with a soft rag and water. Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid.