WORKPRO 60x24 Inch Heavy-Duty Adjustable Workbench with Leveling Foot

Introduction

This manual provides essential information for the safe assembly, operation, and maintenance of the WORKPRO 60x24 inch Heavy-Duty Adjustable Workbench with Leveling Foot (Model W082137A).

Important Safety Precautions: Read and follow all safety rules and operating instructions before first use.

Product Intended Use: For indoor use only. Not designed for commercial or industrial usage.

Assembly Note: Assembly requires at least two people. Ensure all components are present before starting. Refer to the package contents and assembly steps carefully.

Contact Information: For missing components or support, email service@greatstartools.com or call 877-876-7562.

Distributed by: Hangzhou GreatStar Industrial Co., Ltd.

Manufactured in: China

Safety Information

To reduce the risk of serious injury, read and follow the safety instructions below before assembling and using this product.

General Precautions

• Check all nuts and bolts periodically for tightness.
• DO NOT leave children unattended near this product.
• Keep the product on level surfaces to prevent instability and tipping, which could cause injury or damage.
• DO NOT alter the product in any manner (e.g., welding external bar locks, attaching electrical equipment).
• Assembly or maintenance must be carried out by adults only.
• Use at least two people to move, assemble, or install the workbench.
• DO NOT stand on the product or use it as a scaffold.

Extension Cord Usage

• Use only a three-wire extension cord with all three prongs intact. Never remove the grounding prong.
• Connect to a 125Volt GFCI protected outlet with proper ground. If a GFCI outlet is unavailable, use an extension cord with built-in GFCI protection.
• Check the cord's insulation and plugs before use; do not use if worn or damaged.
• Do NOT overload the extension cord.
• Do NOT connect the extension cord to an outlet supplying critical safety equipment.
• Ensure the power supply cord is unplugged before servicing or cleaning.

Electrical Shock Hazard

• Do not plug the cord into an outlet with wet hands.
• Do not use the workbench near a bathtub, shower, or swimming pool.
• Workbench plugs must match the outlet. Never modify the plug.
• Avoid body contact with earthed or grounded surfaces.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with Class B digital device limits, providing reasonable protection against harmful interference in residential installations. If interference occurs, try measures like reorienting the antenna, increasing separation, or using a different circuit. Consult a dealer or technician if needed.

Specifications

Package Contents

Ensure all components are present. If any components are missing, do not proceed with assembly. Contact service@greatstartools.com or 877-876-7562.

Diagram Description: An illustration shows the workbench frame with labels for parts A (Leg), B (Leg with power strip), C (Beam), D (Rubber wood top), E (Table stiffener), F (Support rod), AA (Phillips head self tapping screw), and BB (Inner hexagonal bolt). A hook is also indicated.

Tools Required (Not Included)

• Electric Drill
• PH2 Screwdriver
• 13mm Combination Spanner
• 19mm Combination Spanner
• 3/16" (5mm) Hex Key

Assembly Instructions

Note: Assemble on a flat surface. A piece of cardboard is recommended to protect the product from scratches. Do not tighten all bolts and screws until Step 4.

Step 1: Attach the Beams

Attach the leg (A) and leg with power strip (B) to beams (C) using 8pcs bolts (BB).

Diagram Description: An illustration shows the two legs (A and B) being connected to the two beams (C) using bolts (BB). A close-up view shows the connection points.

Step 2: Attach the Support Rod

Align the support rod's (F) large hole with legs (A&B) using 4pcs bolts (BB).

Diagram Description: An illustration shows the support rod (F) being attached to the legs (A and B) using bolts (BB). A close-up highlights the "Large hole" on the support rod aligning with the leg.

Step 3: Attach the Rubber Wood Top

Place rubber wood top (D) facing down on a flat surface with positioning labels facing upward. Use a soft moving blanket or packaging material to protect the top during assembly.

• Align the legs with the corresponding positioning labels, and attach the support rod (F) to the beams (C) using 4pcs screws (AA) with an electric drill.
• Install the legs (A&B) & beams (C) onto the rubber wood top (D) using 20pcs screws (AA) with an electric drill.

Note: An electric drill is recommended due to the hardness of the wood.

Note: It is recommended to assemble the leg with the power strip close to the "WORKPRO" brand side, but its position can be adjusted as needed.

Diagram Description: Illustrations show the rubber wood top (D) placed upside down. Screws (AA) are used to attach the legs (A, B) and beams (C) to the top. Another diagram shows the support rod (F) being attached to the beams (C) with screws (AA). A warning box indicates not to install two specific screws used for the table stiffener (E) in this step.

Step 4: Attach the Table Stiffener

Attach the table stiffener (E) to the rubber wood top (D) with 6 pcs #5x20 Phillips head self tapping screws (AA).

Diagram Description: An illustration shows the table stiffener (E) being attached to the underside of the rubber wood top (D) using screws (AA).

Step 5: Adjust the Height of Workbench

Adjust the position of screws using a 3/16" (5mm) hex key and 13mm combination spanner to achieve the desired height.

Note: The adjustable height range is from 30 1/2" to 38 3/8".

Diagram Description: Two illustrations show the leg adjustment mechanism, indicating screws being manipulated with a hex key and spanner to change the workbench height.

Step 6: Adjust the Level of Workbench

Easily level the workbench using its height-adjustable leg pads. Rotate the pad to the suitable position and lock with the corresponding nuts (M12) using the 19mm combination spanner.

Diagram Description: An illustration shows a leg pad being rotated (? "rise up") and a nut being tightened (⚙️ "lock nut") using a spanner to level the workbench.

Step 7: Placement of Power Plug

The power plug and cord can be hung on the hook.

Diagram Description: An illustration shows the power cord and plug hanging neatly on the designated hook.

Power Strip Removal

Note: It is strongly recommended NOT to remove the power strip. If removal is necessary, follow these steps:

• Unscrew 1 pc M4*10 bolt (2), and 1 pc M4 nut (3).
• Push the power strip (1) in the indicated direction and remove it.

Diagram Description: An illustration shows the power strip (labeled 1) and its mounting hardware (bolt 2, nut 3). An arrow indicates the direction to push the power strip for removal.

Cleaning and Maintenance

• Check all nuts and bolts periodically for tightness. Tighten when required.
• Periodically clean the workbench surfaces with a soft rag and water. Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid.

Customer Service

If you are experiencing difficulty using this product or require support, please send an email to service@greatstartools.com or call 877-876-7562.