Kwikset Halo Select: Wi-Fi and Matter Enabled Smart Lock
Installation and Reference Guide
Model: 53861-001 Rev 01
Welcome
Welcome to the Kwikset family! This guide will help you get started with your new Halo Select smart lock.
For assistance, please visit the Kwikset support center at kwikset.com/support or call 1-800-327-5625.
Getting Started
To access an interactive version of this installation guide, download the Kwikset app:
Available on the App Store and Google Play.
Parts in the Box
Assemblies:
- Exterior assembly
- Interior assembly
- Interior cover
Box 1:
- Latch (Part 03809)
- Batteries (4x AA)
Box 2:
- Door sensor magnet
- Strike
Box 3:
- Mounting plate (Part 64844)
- Mounting screws (Part 52502)
- Keys
- SmartKey™ tool
Required Tools
- Phillips head screwdriver
- Ruler
⚠️ No electric drills
Installation
Step 1: Measure Door Thickness
Ensure your door thickness is between 1-3/4" and 2" (44mm - 51mm).
If door thickness is greater than 2" (51mm), contact Kwikset customer service at 1-800-327-5625. A thick door installation kit may be required.
Step 2: Remove Existing Deadbolt
Your new lock supports door thicknesses of 1-3/4" to 2" (44mm to 51mm) and a door bore hole diameter of 2-1/8" (54mm).
If drilling a new door, use the supplied template and instructions available at kwikset.com/doorprep.
Step 3: Install the Latch
- Extend the latch bolt.
- Ensure the 'UP' marking is on top.
- If the D-shaped hole is not centered in the bore hole, rotate the latch face to extend the latch.
If your door requires a drive-in latch, please contact Kwikset at 1-800-327-5625.
Use the longer screws (03809) if the holes are worn out. You will have two extra screws.
Step 4: Install the Strike and Sensor Magnet
Install the strike plate onto the door jamb. Use the longer screws (46780) closest to the door jamb for a secure fit. Ensure a 1" (25 mm) hole depth for the strike.
Peel the liner from the door sensor magnet.
Place the magnet above the strike on the door jamb. Ensure the surface is clean, and press firmly for 10 seconds.
Step 5: Install the Exterior Assembly
Route the cable from the exterior assembly under the latch.
Ensure the cable goes under the latch.
Step 6: Install the Interior Assembly
Inside the door:
Keep the mounting plate parallel to the door edge.
Tighten the screws (64844) evenly. DO NOT over-tighten.
Route the cable through the bottom hole of the mounting plate.
Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the screws.
Install the interior assembly onto the mounting plate.
Ensure the spindle fully engages with the turnpiece shaft.
Secure the interior assembly using screws (52502).
Step 7: Install Batteries and Battery Pack
Insert (4) AA batteries (included) into the battery tray. Ensure correct polarity. Use new, non-rechargeable alkaline batteries only.
With the door open, install the battery pack. NOTE: The lock must be installed on the door before inserting the batteries.
Ensure bottom tabs of the battery pack are placed in the slots of the interior assembly before fully inserting the battery pack. The battery pack should be flush after installation if inserted properly.
Complete Your Lock Setup
Download the Kwikset app and create an account to complete the setup process. Follow the setup instructions within the Kwikset app.
The Kwikset app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), ensure this step is performed by the homeowner.
Reference Guide
Locked State
To lock your door, press the lock icon ?. The bolt will extend, and the screen will display the Locked LED Indicator and play the locked tone. The amber connectivity icon will remain on for 1.5 seconds.
Unlocked State
To unlock your door, enter your access code. The bolt will retract, and the screen will display the Unlocked LED Indicator and play the unlocked tone. The green connectivity icon will remain on for 1.5 seconds.
SmartKey® Re-key
Re-key the lock to work with your existing key by following the SmartKey® Re-key instructions. NOTE: If Auto-Lock is enabled, remove the battery pack before re-keying your lock.
Exterior LED Indicators
- Amber: Locked
- Green: Unlocked
- Alternating Red flashing: Lock Jammed
- Red: Low Battery
- Red: Invalid Credentials
- Red: Lockout
Interior Status LED Indicators
- Green (Slow Blinking): Unlocked
- Amber (Blinking): Locked
- Red (Blinking): Low Battery
Factory Reset
Factory Reset will:
- Delete all access codes and associated schedules.
- Reset lock settings to default.
- Show the lock as offline in the Kwikset App.
- Deactivate the lock, requiring it to be set up as new.
Factory Reset should be used when:
- You want to change the lock owner.
- You have lost your phone.
- You are troubleshooting the lock.
Procedure:
- Remove the battery pack, then press and hold the Programming Button.
- While still holding the Programming Button, insert the battery pack. Continue holding the Programming Button for 30 seconds.
- After 30 seconds, the Status LED light will flash RED and the lock will beep. Release the Programming Button.
- Press the Programming Button once within 5 seconds of the Status LED light displaying RED to confirm factory reset.
- SUCCESS: The lock will play a two-tone sound, and the Status LED light will flash PURPLE then GREEN.
- UNSUCCESSFUL: The lock will play a single-tone sound, and the Status LED light will flash RED.
Network Reset
Resets all Bluetooth, Wi-Fi, and Matter connections. Access codes and lock settings will remain.
- Press Button A for 3 seconds until the Status LED light shows solid AMBER. Release Button A.
- Press the Programming Button once while the Status LED light is solid AMBER.
SUCCESS: Lock will play a two-tone sound, Status LED light will flash GREEN, then PURPLE, then GREEN again.
UNSUCCESSFUL: Lock will play a single-tone sound, Status LED light will flash RED.
System Reset
Removes all access codes and associated schedules. Resets lock settings to default. Bluetooth, Wi-Fi, and Matter connections will remain.
- Press Button A 10 times at 1-second intervals until the Status LED light shows solid AMBER.
- Press the Programming Button once while the Status LED light is solid AMBER.
SUCCESS: Status LED light will flash PURPLE, then GREEN, then the lock will beep.
UNSUCCESSFUL: Lock will play a single-tone sound, Status LED light will flash RED.
Halo Select at a Glance
Exterior Components:
- Warning Icon ⚠️
- Keypad
- Checkmark Icon ✔️
- Keyway
- SmartKey™ tool access
- Connectivity Icon
- Lock Icon ?
Interior Components (cover removed):
- Battery Icon ?
- Button A
- Pairing Button
- Status LED
- Programming Button
Troubleshooting
If you have any issues, please visit our support center: kwikset.com/support or call 1-800-327-5625.
Important Safeguards
- Read all instructions in their entirety.
- Familiarize yourself with all warning and caution statements.
- Remind all family members of safety precautions.
- Always have access to your lock's standard key.
- If using the Auto-Lock features, ensure you have your smartphone or standard key with you to prevent locking yourself out.
- Familiarize yourself with all light bar error notifications.
- Replace low batteries immediately.
- Dispose of used batteries according to local laws and regulations.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder's hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Regulatory Compliance
This product complies with standards established by the following regulatory bodies:
- Federal Communications Commission (FCC)
- Industry Canada
FCC Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
FCC ID: NUL-HAL3S
IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
Industry Canada Compliance:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
IC: 3022A-HAL3S
Kwikset Smart Locks Application | Kwikset
