MiBoxer RGB+CCT LED Strip Controller

Introduction

The controller adopts the widely used 2.4GHz wireless technology, offering efficient power consumption management and auto-synchronization functions. It is ideal for controlling hotel lighting and home lighting, providing a selection of 16 million colors.

Specifications

Model No.: FUT039

• Voltage: DC12V~24V
• Output Current: Max 6A/channel
• Total Output: Max 12A
• Working Temperature: -20°C to 55°C
• Connection Mode: Common Anode
• Output Signal: 2.4GHz RF
• Dimensions: 114 x 52 x 26 mm
• Light Effect: RGB+CCT
• Remote Control Distance: 30m
• Signal Transmission Distance: 30m
• IP Rating: IP20
• Compatibility: Mi-Light/MiBoxer 2.4GHz series remote controls

The MiBoxer FUT039 controller is a compact rectangular unit. It features a DC input port (12V-24V) and multiple output terminals for connecting LED strips. It includes a 'SET' button for pairing and mode selection, along with indicator LEDs. The unit is designed for indoor use (IP20 rated) and measures 114mm x 52mm x 26mm.

Dynamic Mode Sheet

Signal Transmitting

One MiBoxer controller can change the lamps from a distance. When controlled by the same controller, lamps will synchronize. If a controller is more than 30 meters away from the lamps, it can send the signal to another lamp within 30 meters. As long as another lamp is within 30 meters, all lamps can be controlled synchronously. The more lamps installed, the better the synchronization effect.

This diagram illustrates the auto-synchronization feature. A primary controller transmits a signal to a nearby LED strip. This strip then acts as a repeater, relaying the signal to another strip within a 30-meter range. This chain reaction allows for synchronized control of multiple LED strips across a larger area, even if they are not all within direct range of the initial controller.

Link/Unlink

Compatible with Mi-Light Remote Controls (Purchased Separately)

Compatible remote controls include FUT089, FUT088, FUT092, FUT096, B8, B3/T3, B4/T4, and the 2.4GHz Gateway WL-Box1. Lighting can be activated after linking with remotes. For more details, please refer to the specific remote control instructions.

DMX512 LED Transmitter Link/Unlink

Compatible with DMX512 LED Transmitter (Purchased Separately)

Linking Procedure

• Step 1: Select the desired zone for the controller by pressing the '+' or '-' buttons (e.g., 'CH12' indicates zone 12).
• Step 2: Switch off the connected light. Wait 10 seconds, then switch it back on.
• Step 3: Once the controller's pilot lamp is illuminated, quickly press the 'SET' button 3 times within 3 seconds.
• Result: The controller's pilot lamp will blink slowly 3 times, confirming successful linking.

Unlinking Procedure

• Step 1: Switch off the connected light. Wait 10 seconds, then switch it back on.
• Step 2: Once the controller's pilot lamp is illuminated, quickly press the 'SET' button 5 times within 3 seconds.
• Result: The controller's pilot lamp will blink quickly 10 times, confirming successful unlinking.

Note: If the link or unlink process fails, please repeat the steps.

DMX512 LED Transmitter Connection Diagram

The diagram depicts a DMX512 LED Transmitter connected to a DMX512 Control Panel. The transmitter broadcasts a 2.4GHz wireless signal, which is then distributed to multiple zones (labeled 1 through 15+). Each zone can control an unlimited number of MiBoxer controllers, enabling centralized DMX control of the LED lighting system.

Attention

• Verify that the input voltage of the power supply matches the controller's requirements. Ensure correct connection of both positive (+) and negative (-) terminals to prevent damage to the controller.
• Avoid connecting wires while the power is on. Ensure all connections are correct and there are no short circuits before powering on the system.
• Do not install or operate the controller in areas with significant metal surfaces or strong electromagnetic interference, as this can negatively impact the remote control range.

Certifications: CE, UKCA, RoHS

Origin: Made in China

Note: Controller is not suitable for use in humid environments.