INSTRUCTION MANUAL
Keep the Instructions for Future Reference.
If you purchased the furniture on-line and have any questions or concerns please contact us with email. Email: teamaftersale@outlook.com
WARNING
Proper use of the chair is for single person seating only. The chair is not to be used for standing purposes and will not function as a step-ladder. Use on even surfaces only. The chair tested for use at weight of 225 lbs. Improper use of this product or failure to use as directed may result in injury.
IMPORTANT
Please read all the instructions and warnings before assembling. In order to make the whole product adjust to the best, please install all the screws on the product before fully tighten and note to put the washer to the screw before putting the screw into the screw hole.
SAFETY INFORMATION
- Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product construction.
- Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.
- Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
- Check all bolts for tightness before use. IMPORTANT: Check and tighten bolts often to keep them secure!
- The chair is not to be used for standing purposes and will not function as a tool or step-ladder. Use on even surfaces only.
CARE & MAINTENANCE
STAIN RESISTANT CUSHIONS CARE: KEEP THE CUSHIONS IN STORAGE IN RAINY DAYS
SPILLS
Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushion to air dry.
FABRIC CARE
Hand wash only, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
RESIN WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Over time nuts and bolts can loosen. Occasionally, check nuts and bolts on furniture, re-tighten if necessary.
RUST PREVENTION
Use a waterproof furniture cover during rain or snow, or any shield that can be covered.
Part List
- A: Back Panel × 2
- B: Seat Panel × 2
- C: Left Chair Arm × 2
- D: Right Chair Arm × 2
- E: Seat Cushion × 2
Diagram description: Line drawings of the chair components A (Back Panel), B (Seat Panel), C (Left Chair Arm), D (Right Chair Arm), and E (Seat Cushion).
Hardware
- G: Bolt M6 x 35 × 20
- H: Washer M6 × 20
- I: Allen Key × 1
Diagram description: Line drawings of the hardware components G (Bolt), H (Washer), and I (Allen Key).
Assembly Instructions
Assembly Tip: Please screw the parts together at 80% loose, it will help you assemble them easily. When all the parts are assembled together, tighten the screws up 100% in the end to make the product stable.
Note: This assembly is designed for 1 Person Assembly.
STEP 1: Attach Seat Panel to Back Panel
Attach Seat Panel (B) to Back Panel (A) using Bolts (G) and Washers (H) as shown. Tighten the bolts to 80% tightness.
Diagram description: Shows attaching Seat Panel (B) to Back Panel (A) with Bolts (G) and Washers (H). A close-up view illustrates the bolt and washer assembly.
STEP 2: Attach to Left Chair Arm
Attach Seat Panel (B) and Back Panel (A) to Left Chair Arm (C) using Bolts (G) and Washers (H) as shown. Tighten the bolts to 80% tightness.
Diagram description: Shows attaching the assembled panels (A and B) to the Left Chair Arm (C) using Bolts (G) and Washers (H). A close-up view illustrates the bolt and washer assembly.
STEP 3: Attach to Right Chair Arm
Attach Seat Panel (B) and Back Panel (A) to Right Chair Arm (D) using Bolts (G) and Washers (H) as shown. Adjust the balance of the chair and tighten the bolts to 100% tightness.
Diagram description: Shows attaching the assembled panels (A and B) to the Right Chair Arm (D) using Bolts (G) and Washers (H). A close-up view illustrates the bolt and washer assembly. A graphic indicates to tighten bolts to 100% tightness.
STEP 4: Attach Seat Cushion
Put Seat Cushion (E) to chair frame. Secure the cushion to Seat Panel (B) using the Velcro loop under the cushion.
Diagram description: Shows placing the Seat Cushion (E) onto the chair frame and securing it with a Velcro loop. A close-up view shows the Velcro attachment.
STEP 5: Repeat Assembly
Repeat the assembly process for a second chair, as shown.
Diagram description: Shows two completed Outdoor Wicker Dining Chairs.
STEP 6: Level the Chair
The chair can be leveled by adjusting the knobs on the 2 rear legs.
Diagram description: Shows a close-up view of a chair leg with an adjustable knob for leveling the chair.
