Outdoor Wicker Dining Chair

Keep these instructions for future reference. If you purchased the furniture online and have any questions or concerns, please contact teamaftersale@outlook.com.

WARNING:

• Proper use of the chair is for single person seating only.
• The chair is not to be used for standing purposes and will not function as a step-ladder.
• Use on even surfaces only.
• The chair is tested for use at a weight of 225 lbs.
• Improper use of this product or failure to use as directed may result in injury.

IMPORTANT:

Please read all instructions and warnings before assembling. To ensure the best fit for the product, please install all screws loosely before fully tightening. Note to place the washer onto the screw before inserting the screw into the screw hole.

SAFETY INFORMATION:

• Keep all children and pets away from the assembly area. Children and pets should be supervised when they are in the area of the product construction.
• Keep the assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires.
• Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
• Check all bolts for tightness before use. IMPORTANT - check and tighten bolts often to keep them secure!
• The chair is not to be used for standing purposes and will not function as a tool or step-ladder. Use on even surfaces only.

CARE & MAINTENANCE:

• STAIN RESISTANT CUSHIONS CARE: Keep the cushions in storage on rainy days.
• SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat the process if necessary until the stain is gone. Allow the cushion to air dry.
• FABRIC CARE: Hand wash only, use non-chlorine bleach when needed, lay flat to dry. Use a cool iron if necessary. Do not dry clean.
• RESIN WICKER PRODUCT CARE: Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects. Wash with a mild solution of soap and water, rinse thoroughly, and dry completely. Do not use strong detergent or abrasive cleaners. Over time, nuts and bolts can loosen. Occasionally, check nuts and bolts on the furniture and re-tighten if necessary.
• RUST PREVENTION: Use a waterproof furniture cover during rain or snow, or any shield that can be used for covering.

Part List

The following parts are included:

• A: Back Panel (x2)
• B: Seat Panel (x2)
• C: Left Chair Arm (x2)
• D: Right Chair Arm (x2)
• E: Seat Cushion (x2)

Hardware

• G: Bolt M6 x 35 (x20)
• H: Washer M6 (x20)
• I: Allen Key (x1)

1 Person Assembly

ASSEMBLY TIP:

Please screw the parts together at 80% loose initially. This will help you assemble them more easily. When all parts are assembled together, tighten the screws up to 100% to make the product stable.

Step 1: Attach Seat Panel to Back Panel

Attach Seat Panel (B) to Back Panel (A) using Bolts (G) and Washers (H) as shown.

Step 2: Attach Chair Arms to Seat and Back Panels

Attach Seat Panel (B) and Back Panel (A) to Left Chair Arm (C) using Bolts (G) and Washers (H) as shown.

Attach Seat Panel (B) and Back Panel (A) to Right Chair Arm (D) using Bolts (G) and Washers (H) as shown.

Step 3: Final Tightening

After attaching all parts, tighten all the bolts to 100% tightness.

Step 4: Place Seat Cushion

Place Seat Cushion (E) onto the chair frame. Secure the cushion to the Seat Panel (B) using the Velcro loops located under the cushion.

Step 5: Repeat for Second Chair

Repeat the assembly process for the second chair.

Step 6: Leveling the Chair

The chair can be leveled by adjusting the knobs on the two rear legs. Turn the knobs to raise or lower the legs until the chair is stable and level.

The assembled chairs are now ready for use.