Simyke U0s Baby Monitor User Manual

Important Safety Instructions

Read all instructions and warnings before using this product.

WARNING:

• STRANGULATION HAZARD: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (1m) away). NEVER PLACE THE CAMERA OR CORD IN OR NEAR CRIB OR PLAYPEN. Secure the cord at least 3 ft away from crib or playpen.
• CHOKING HAZARD: This product contains small parts which may cause choking.
• SHOCK WARNING: To prevent electric shock, NEVER use the transmitter or receiver near water, including near a bathtub, sink, laundry tub, wet basement, etc.
• CAUTION: Only insert a battery pack of the same type. Risk of explosion if battery is replaced with an incorrect type.

Use only the DC adapters provided. Adult assembly is required. Keep small parts away from children when assembling. This product is not a toy; do not allow children to play with it. This product is NOT intended to replace proper adult supervision of children. You MUST check your child's activity regularly, as this product will not alert parents to silent activities of a child.

Do not allow water damage to the camera unit, monitor unit, power adapter, or charging cable, as this can cause overheating of charging components. Do not use unofficial third-party charging cables or power adapters, especially high wattage adapters, as this may result in overheating of the charging port or cable. Only use the charging cables and adapters provided in the box.

FCC Statements

These devices, including the Baby Camera and Baby Monitor, comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: These devices may not cause harmful interference, and these devices must accept any interference received, including interference that may cause undesired operation.

These are Class B Digital Devices. They have been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. These devices generate, use, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If these devices do not cause harmful interference to radio or television reception (which can be determined by turning the devices off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult an experienced radio/TV technician for help.

Caution to the user: The Federal Communications Commission warns users that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Overview

What's in the Box

• 1 x Baby Camera
• 1 x Baby Monitor
• 2 x Power Adapter
• 2 x Charging Cable
• 1 x User Manual
• 1 x Wall-Mounting Parts

NOTE: Power adapter varies by region.

Product Overview - Monitor Unit

Monitor Unit Components:

• 1. Volume LED [? LED]
• 2. Power LED [? LED]
• 3. Power Button [▶️ Power Button]
• 4. Menu [⚙️ Menu Button]
• 5. Brightness +/Up Button [? + / ⬆️ Button]
• 6. Volume - / Left Button [? - / ⬅️ Button]
• 7. Volume + / Right Button [? + / ➡️ Button]
• 8. OK/Zoom in/Zoom out Button [✔️ / ? Button]
• 9. Brightness -/Down Button [? - / ⬇️ Button]
• 10. Talk Button [? Talk Button]
• 11. Microphone [? Microphone]
• 12. Screen [?️ Screen]
• 13. Battery Compartment [? Compartment]
• 14. Stand [? Stand]
• 15. Speaker [? Speaker]
• 16. DC-Jack [? DC-Jack]

Product Overview - Camera Unit

Camera Unit Components:

• 1. CMOS Sensor
• 2. Power LED [? LED]
• 3. Microphone [? Microphone]
• 4. Speaker [? Speaker]
• 5. DC-Jack [? DC-Jack]
• 6. Pair Button [? Pair Button]
• 7. Temperature Sensor [?️ Sensor]

Specifications

System General

Monitor Unit

Camera Unit

Status Indication Overview (Upper Screen Bar)

Menu Options Overview (Lower Screen Bar)

Getting Started

Charging and Powering the Baby Monitor

Turn on the Camera Unit

Only use the DC adapter included in this package. Use the provided DC adapter to connect the wall outlet with the camera unit. Once the adapter is connected, the unit will turn on automatically and the power LED will light up.

NOTE: Only use the enclosed camera Power Adapter.

Turn on the Monitor Unit

• Only use the DC adapter included in this package.
• The monitor unit is supplied with a built-in rechargeable Li-ion battery.
• It is recommended to connect the monitor to the adapter plugged into the mains whenever possible to keep the battery charged.

Press and hold the POWER button on the right side of the monitor unit. Once the monitor unit is turned on, the power LED will light up and the image will display on the LCD screen.

Placement of the Baby Monitor

The camera unit can be placed on a tabletop or hung on the wall. Place the baby monitor in a location where air can circulate freely. Do not place on soft quilts or blankets or in the corners of cupboards, shelves, etc.

Place the baby monitor away from heat sources such as radiators, chimneys, cookers, and direct sunlight. Place the camera unit away from TV sets, microwave ovens, and radios. Intense radio signals from these devices could cause noise or degrade sound and images. If this occurs, move the camera to another location.

Place the camera within 15 feet of the area being monitored for best picture results. Baby monitors and cameras with power cords should never be hung on or near the crib as this can cause a strangulation hazard. Power cords should be kept no less than 3 feet away from the crib and the baby's reach at all times.

Registration (Pairing)

The camera unit is pre-registered to your monitor unit. Re-registration is only necessary if the camera unit loses its pairing. To re-register or register a new camera unit, follow these steps:

1. Press the MENU button on the monitor unit; the menu bar will appear.
2. Press the LEFT or RIGHT button until the camera icon [?️ cam] is highlighted.
3. Press the UP or DOWN button until the ADD icon [➕ add] is highlighted, then press the OK button.
4. Press the UP or DOWN button to select the desired camera channel (e.g., cam 1) and press the OK button to start searching for a camera unit.
5. Press and hold the PAIR button on the back of the camera unit for at least 3 seconds. The power LED light should flash to indicate the camera unit is in pairing mode. If it does not flash, press and hold the PAIR button until the LED light flashes.

NOTE: If a camera unit was previously registered with another monitor unit, registering it with the current monitor unit will overwrite the old registration on the camera unit.

Using the Simyke U0s Baby Monitor

OSD Mode Operation

Power Save/Screen Off/Sleep Mode

Press the POWER button to enter sleep mode. Long press the POWER button to turn the screen on/off.

Volume Adjustment

Press the RIGHT button to increase the volume. Press the LEFT button to decrease the volume.

Brightness Adjustment

Press the UP button to increase the brightness. Press the DOWN button to decrease the brightness.

Digital Zoom & Pan/Tilt

Long press the OK button to zoom in, then press the OK button again to zoom out. While zoomed in, press the LEFT button to pan left, RIGHT to pan right, UP to tilt up, and DOWN to tilt down. The zoom icon [?] will be displayed on the top of the screen during zoom mode.

NOTE: To adjust volume or brightness, exit zoom mode first.

Talk to Baby

To talk, press and hold the TALK button on the front of the monitor. Release the button when finished talking to listen to your baby. You cannot listen to your baby while talking. The talk icon [?] will be displayed on the top of the screen when this function is active.

Infrared Night Vision (Automatic)

The infrared night vision function allows the camera to capture images in dark or low-light conditions. In night vision mode, only black and white images are displayed on the monitor. The night vision icon [?] will be displayed on the top of the screen when the camera is in night vision mode.

Menu Operation

Lullaby Setting

1. Press the MENU button; the menu will appear.
2. Press the LEFT or RIGHT button until the lullaby icon [?] is highlighted.
3. Press the UP or DOWN button to select one of the 6 available lullabies for single or sequential playing.
4. Press the MENU button to exit.

NOTE: The lullaby icon [?] displays when a lullaby is playing. Single playing lasts 15 minutes. Sequential playing plays all lullabies.

Alarm Setting

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the alarm icon [⏰] is highlighted.
3. Press the UP or DOWN button to select the desired time interval: 2h, 4h, 6h, or OFF (default is OFF). Press the OK button to confirm.

VOX Setting

This mode controls sound activation. If no sound is detected near the camera for 3 or 5 minutes, transmission stops, and the monitor screen turns off. When sound exceeding the sensitivity level is detected, the monitor alerts the user.

To change the VOX level:

1. Press the MENU button; the menu will appear.
2. Press the LEFT or RIGHT button until the VOX icon [?] is highlighted, then press the UP or DOWN button to select the desired level (VOX-L for low sensitivity, VOX-H for high sensitivity). Press the OK button to confirm.
3. Navigate back to the previous menu. Press the UP or DOWN button until the time icon [⏰] is highlighted, then press the OK button.
4. Press the UP or DOWN button to select the desired time setting for VOX mode.
5. Press the MENU button to exit.

NOTE: VOX Mode default is OFF. VOX-L is low sensitivity; VOX-H is high sensitivity.

Camera Control

Add (Pair) a Camera

1. Press the MENU button on the monitor unit; the menu bar will appear.
2. Press the LEFT or RIGHT button until the camera icon [?️ cam] is highlighted.
3. Press the UP or DOWN button until the ADD icon [➕ add] is highlighted, and press the OK button.
4. Press the UP or DOWN button to select the desired camera channel (e.g., cam 1) and press the OK button to start searching for a camera unit.
5. Press and hold the PAIR button on the back of the camera unit for at least 3 seconds. The power LED light should flash to indicate the camera unit is in pairing mode. If it does not flash, press and hold the PAIR button until the LED light flashes.

NOTE: Registering a camera unit with another monitor unit will overwrite the old registration.

Delete a Camera

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the camera icon [?️ cam] is highlighted, and the delete/add/view/scan menu will show.
3. Press the UP or DOWN button to select the DELETE icon [❌ del], and press the OK button to confirm.
4. Camera channels (cam 1/ cam 2/cam 3/ cam 4) will be displayed. Press the UP or DOWN button to select the desired camera, and press the OK button to delete its registration from your monitor unit.

NOTE: A camera channel must be deleted before pairing a new camera unit to it.

View a Camera

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the camera icon [?️ cam] is highlighted, and the delete/add/view/scan menu will show.
3. Press the UP or DOWN button to select the VIEW icon [?️ view], and press the OK button to confirm.
4. Camera channels (cam 1/ cam 2/cam 3/cam 4) will be displayed. Press the UP or DOWN button to select the desired camera unit to view.

Scan Camera

This function automatically cycles through paired camera channels, displaying each for 10 seconds. This is only applicable if you have more than one camera unit.

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the camera icon [?️ cam] is highlighted, and the delete/add/view/scan menu will show.
3. Press the UP or DOWN button to select the SCAN icon [? scan], and press the OK button to confirm.
4. The screen will display video from different paired cameras in a loop (cam 1/ cam 2/cam 3/ cam 4), changing every 10 seconds.

NOTE: In scan mode, the monitor unit will stop scanning and alert you if a camera unit is out of range or powered off.

Warning Volume Setting

This controls the volume of an audio 'beep' sound from the monitor unit to alert you when the unit is low on battery or out of range.

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the warning volume icon [?] is highlighted.
3. Press the UP or DOWN button to select the volume level: high, low, or OFF.

Calendar Setting

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the calendar icon [?] is highlighted, and the calendar will show.
3. Press the OK button to start changing the date and time.
4. Press the LEFT or RIGHT button to select the date and time fields.
5. Press the UP or DOWN button to set the date and time, then press the OK button to confirm.

Temperature Unit Setting

1. Press the MENU button; the menu bar will appear.
2. Press the LEFT or RIGHT button until the temperature icon [?️] is highlighted.
3. Press the UP or DOWN button to select between Celsius (°C) or Fahrenheit (°F), and press the OK button to confirm.

Customer Service

Warranty

Simyke guarantees a 12-month warranty and professional after-sale service within 24 hours.

Contact Us

For any questions, please contact Simyke via official email addresses:

• US: ✉️ usservice@simyke.net
• EU: ✉️ euservice@simyke.net

Website: ? www.simyke.net

FCC-SAR/Exposure Information

The Baby Monitor is designed to meet the radio wave exposure requirements set by the Federal Communications Commission (USA). These requirements specify a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported during product certification for body-worn use is 1.098 W/kg.

The Baby Camera complies with FCC radiation exposure limits for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.