Simyke BME50P Baby Monitor User Manual

Safety Instructions

WARNING:

• STRANGULATION HAZARD-Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (1m) away).
• NEVER PLACE THE CAMERA OR CORD IN OR NEAR CRIB OR PLAYPEN. Secure the cord at least 3 ft away from crib or playpen.
• CHOKING HAZARD-This product contains small parts which may cause choking.
• SHOCK WARNING-To prevent electric shock, NEVER use the transmitter or receiver near water, including near a bathtub, sink, laundry tub, wet basement, etc.
• CAUTION-Only insert a battery pack of the same type. Risk of explosion if battery is replaced with an incorrect type.
• Use only the DC adapters provided.
• Adult assembly is required. Keep small parts away from children when you are assembling.
• This product is not a toy. Do not allow children to play with it.
• Do not allow water damage to the camera unit, monitor unit, power adapter, or charging cable which cause overheat of the charging components.

This product is NOT intended to replace proper adult supervision of children.

You MUST check your child's activity regularly, as this product will not alert parents to silent activities of a child.

Before using this product, read and follow all instructions and warnings contained in this booklet.

Do not use unofficial third party charging cables to charge the device. This may result in overheat of the charging port. Only use the charging cables provided in the box.

Do not use unofficial third party power adapters, especially high wattage adapters. This may result in overheat of the cable and/or charging port. Only use the adapter provided in the box.

FCC Statements

These devices, including Baby Camera and Baby Monitor, comply with Part 15 of the FCC rules. Operation is subject to the following two conditions:

• These devices may not cause harmful interference.
• These devices must accept any interference received, including interference that may cause undesired operation.

Class B Digital Device. These equipments have been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. These equipments generate, use, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If these equipments does cause harmful interference to radio or television reception, which can be determined by turning the equipments off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult an experienced radio / TV technician for help.

Warn user. The Federal Communications Commission warns the users that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipments.

Overview

What's in the Box

• 1 x Baby Camera
• 1 x Baby Monitor
• 1 set Power Adapter for BME50P
• 2 set Power Adapter for BME50P-2
• 1 set Power Adapter for BME50P
• 1 x User Manual

NOTE: Power adapter varies by region.

Specifications

System General

• Model Number: BME50P
• RF Frequency: 2400-2483.5MHz
• Optional Camera Channels: cam 1/cam 2/ cam 3/cam 4
• Operating Temperature Range: 0°C-50°C
• Origin: Made in China
• Wireless Communication: WiFi/FHSS
• TX-RX Transmission Range: 1500fts

Monitor Unit

• Input Voltage: 5V
• Operating Power: <1000mA
• LCD Display: 5.0" TFT
• Power Adapter: 5V, 1A
• Charging Cable: 80 ins
• Full Charging Time: 8 Hours
• Duration(Standby Mode): 30 Hours
• Duration (Screen ON): 20 Hours
• Monitor Dimensions (L x W x H): 6.73x3.50x0.71 ins

Camera Unit

• Input Voltage: 5V
• Operating Power: <800mA
• IR/Night Vision: YES
• Picture Sensor: GC1084
• Operating Temperature: 0°C-50°C
• Power Adapter: 5V, 1A
• Charging Cable: 80 ins
• Exposure Control: Auto
• White Balance Control: Auto
• Vertical Turning Angle: Tittle down 90°
• Horizontal Turning Angle: Manual 330°
• Other Special Features: Built in Microphone/speaker
• Camera Dimensions (L x W x H): 2.76x2.76x4.33ins

Menu Options Overview (Lower Screen Bar)

Status Indication Overview (Upper Screen Bar)

Getting Started

Charging and Powering the Baby Monitor

Turn on the Monitor Unit

• Only use the DC adapter included in this package.
• The monitor unit is supplied with a built-in rechargeable Li-ion battery. We suggest to connect the monitor to the adapter plugged into the mains whenever possible, in order to keep the battery charged.
• Press and hold the power button on the lower right of the keypad.

Turn on the Camera Unit

• Only use the DC adapter included in this package.
• Use the provided DC adapter to connect the wall outlet with the camera unit. Once the adapter is connected, the unit will turn on automatically and the power LED will light up.
• NOTE: Only use the enclosed camera Power Adapter.

Once monitor unit turned on, the power LED will light up and the image will display on the LCD screen.

Placement of the Baby Monitor

This camera can be placed on a tabletop or on the wall. Place the baby monitor in an airy place. Do not place on soft quilts or blankets or in the corners of cupboards, shelves, etc.

Baby monitors and cameras with power cords should never be hung on or near the crib as it can cause strangulation hazard. Power cords should be kept no less than 3 ft away from the crib and the baby's reach at all times.

• Place the baby monitor away from heat sources such as radiators, chimneys, cookers and direct sunlight.
• Place the camera unit away from TV sets, microwave oven and radios. The intense radio signals generated by these elements could cause noise or even deteriorate sounds and images which appear on the monitor. If this occurs, move the camera to another location.
• Place the camera within 15 feet of the area being monitored for best picture result.

Wall mount installation

1. Position the crib against the preferred wall in the nursery.
2. Using the Measuring Tape, find the center of the crib and mark the wall with a pencil.
3. Lift the tape up 60 inches and mark at the "Mark Here" indicator.
4. Push the Large Drywall Anchors into each hole and screw them until they are flush.
5. Align the wall mount holes on the Simyke camera unit with the screws on the wall. Slide the Simyke camera unit down until it locks into place.
6. Plug the Power Supply into the right side of the Simyke camera device.
7. Plug the Power Cord into the nearest outlet.

Optimal mounting height 60 in

Using the BME50P Baby Monitor

Work with Plug&Play Display

Registration (Pairing)

The Camera Unit is pre-registered to your monitor unit. You do not need to register it again unless the Camera Unit loses its pairing with the monitor unit. To re-register your Camera Unit, or register a new Camera Unit, follow the procedure below:

1. Press the MENU button of the monitor unit and the menu bar will pop up.
2. Press the LEFT button or RIGHT button until + icon is highlighted.
3. Press the UP button or DOWN button until • icon is highlighted.
4. Press the UP button or DOWN button to select the desired cam and press the OK button to create the registration (pairing) QR code.
5. Follow the instructions on the screen of the monitor and finish the registration (pairing).

NOTE: If a particular Camera Unit was previously registered with another monitor unit, registering with the current monitor unit will overwrite the old registration on the camera Unit.

OSD (On Screen Display) Mode Operation

• Screen Off/Power Off
  Press the power button to get into the SLEEP MODE.
  Long press the power button to turn on/off the screen.
• Volume Adjustment
  Press the Volume&Brightness function key ?️ and the keypad indicator will be displayed on the screen.
  Press the Right button to increase the volume.
  Press the Left button to decrease the volume.
• Brightness Adjustment
  Press the Volume&Brightness function key ?️ and the keypad indicator will be displayed on the screen.
  Press the UP button to increase the brightness.
  Press the DOWN button to decrease the brightness.
• Talk to Baby
  To talk, press and hold the TALK button. Release the button when you have finished talking to and want to listen from the baby's room again. Bear in mind that you will not be able to listen to your baby while talking to the monitor. You will have to stop pressing this button before listening to your baby. When you are using this function, the talk icon will be displayed on the the screen.
• Infrared Night Vision (Automatic)
  The infrared night vision function allows the camera to pick up images of your baby or the monitored area in dark or low light conditions. When using the night vision mode, only black and white images will be displayed on the monitor. (When the camera is in night vision mode, the night vision icon ? will be displayed on the top of the screen).

Menu Operation

• Lullaby Setting
  1. Press the MENU button and the menu will show.
  2. Press the LEFT button or RIGHT button until the lullaby ? icon is highlighted, then press the OK button.
  3. Press the UP button or DOWN button to select one of the 5 available lullabies, single or sequential playing or stop playing.
  4. Press the MENU button to Exit.
  NOTE:
  • Once the lullaby starts playing on, the lullaby icon will display on the top of the screen.
  • Lullaby sequential playing function ? will play all the lullabies each time.
• Alarm Setting
  1. Press the MENU button and the menu bar will pop up.
  2. Press the LEFT button or RIGHT button until the alarm ⏰ icon is highlighted.
  3. Press the UP button or DOWN button to select the desired time from 2h, 4h, 6h and OFF. (The default setting is OFF).
  4. Press the OK button to confirm.
• VOX Setting
  This mode allows you to control the sound activation of your baby monitor. If there is no sound around the camera within or 5min, it will stop the transmission. The monitor screen will turn off when the camera is not transmitting. When the camera detects the sound exceeding the sensitivity level, it will start transmitting the signal to the monitor and alert the user. To change the VOX level, please follow the instructions below:
  1. Press the MENU button and the menu will show.
  2. Press the LEFT button or RIGHT button until the VOX ? icon is highlighted.
  3. Press the UP button or DOWN button to select desired level. Press the OK button to confirm.
  4. Press the MENU button to exit.
  NOTE:
  • ? is low sensitivity level.
  • ? is medium sensitivity level.
  • ? is high sensitivity level.
  • VOX Mode default:OFF
• Camera Control
  
  • Add (Pair) a Camera
    Please refer to the instructions for camera pairing on Page 13.
  • Delete a Camera
    1. Press the MENU button and the menu bar will show.
    2. Press the LEFT button or RIGHT button until the cam ? icon is highlighted and the camera add +/ camera delete X / camera view • / camera scan ? / camera speaker out ? menu will show.
    3. Press the UP button or DOWN button to select the X delete icon, and press the OK button to confirm.
    4. 1/2/3/4 will show, press the UP button or DOWN button to select the desired cam, and press the OK button to delete that registration on your monitor unit.
    NOTE: A cam channel needs to be deleted before pairing to a new camera unit.
  • View a Camera
    1. Press the MENU button and the menu bar will show.
    2. Press the LEFT button or RIGHT button until the cam ? icon is highlighted and the camera add +/ camera delete X / camera view • / camera scan ? / camera speaker out ? menu will show.
    3. Press the UP button or DOWN button to select the view • icon, and press the OK button to confirm.
    4. 1/2/3/4 will show, press the UP button or DOWN button to select the desired camera unit to view.
  • Scan Camera
    This function automatically cycles through your paired camera channels to display each for 30 seconds. This function is only applicable if you have more than 1 camera unit.
    1. Press the MENU button and the menu bar will show.
    2. Press the LEFT button or RIGHT button until the cam ? icon is highlighted and the camera add +/ camera delete X / camera view • / camera scan ? / camera speaker out ? menu will show.
    3. Press the UP button or DOWN button to select the scan ? icon, and press the OK button to confirm.
    4. The screen will display the video from different paired cameras in a loop of, changing every 30 seconds.
    NOTE: When in the scan mode, the monitor unit will stop scanning and alert you if one of the camera unit is out of range or is not powered on.
  • Set Camera Speaker Out Volume
    This setting applies to following features on camera side: Two way talk, lullaby, sound indications for camera status.
    1. Press the MENU button and the menu bar will show.
    2. Press the LEFT button or RIGHT button until the cam ? icon is highlighted and the camera add +/ camera delete X / camera view • / camera scan ? / camera speaker out ? menu will show.
    3. Press the UP button or DOWN button to select the volume ? setting icon, and press the OK button to confirm.
    4. Volume high/Medium /Low will show, press the up button or DOWN button to select the desired level, and press the OK button to confirm.
• Warning Volume Setting
  This setting turns on/off the audio 'beep' sound from the monitor unit to alert you when the unit is low on battery or out of range.
  1. Press the MENU button and the menu bar will show.
  2. Press the LEFT button or RIGHT button until the warning ? icon is highlighted.
  3. Press the UP button or DOWN button to select ON / OFF.
• Temperature Unit Setting
  1. Press the MENU button and the menu bar will show.
  2. Press the LEFT button or RIGHT button until the temperature ?️ icon is highlighted.
  3. Press the UP button or Down button to select between C or F, and press the OK button to confirm.
• LCD Screen Brightness Setting
  1. Press the MENU button and the menu bar will show.
  2. Press the LEFT button or RIGHT button until the warning ☀️ icon is highlighted.
  3. Press the UP button or Down button to select the desired brightness level.
• LCD Screen Speaker Volume Setting
  1. Press the MENU button and the menu bar will show.
  2. Press the LEFT button or RIGHT button until the warning ? icon is highlighted.
  3. Press the UP button or Down button to select the desired volume level.

Work with Smartphone

1. Download & Register
   Download the App and follow the onscreen instructions to complete your initial registration.
2. Pair Device
   Tap 'Pair Device' to pair your phone with Simyke baby monitor.
3. Ready to begin
   Now start your journey with Simyke camera!

Customer Service

Warranty policy

Simyke guarantees 12 months warranty and professional after-sale service within 24 hours.

Contact Us

If you have any questions, please feel free to contact Simyke via their official email address: info@simyke.net

Trouble Shooting