FAREXON Electric Single Motor Standing Desk
Instruction Manual
Important Information
⚠️ IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.
General Guidelines
- Please read the following instruction carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps. Please contact FAREXON support when further information and help are needed.
Notes
- Please follow the assembly instructions precisely and only use the product as intended.
- If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
- Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use product as damage or injury may occur; Please contact FAREXON support for assistance and replacement.
- During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
- It is suggested you regularly check the products bolts and connections to ensure safe use.
- Assemble the item on a soft flat and clean surface to avoid scratches and damage.
Warnings
- During assembly, keep parts and packaging materials away from children and pets as there could cause injury and are a potential choking hazard.
- Avoid sharp objects or corrosive chemicals to prevent damage to the product.
- Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially children.
Components
Please check you have all the pieces listed below.
Part List
| Reference | Description | Part Diagram | Quantity | Material |
|---|---|---|---|---|
| 1 | Desktop-a | [Desktop piece] | 1 | MDF |
| 2 | Desktop-b | [Desktop piece] | 1 | MDF |
| 3 | Desktop-c | [Desktop piece] | 2 | MDF |
| 4 | Left Leg | [Leg assembly] | 1 | Steel |
| 5 | Right Leg | [Leg assembly] | 1 | Steel |
| 6 | Support Beam | [Support beam] | 2 | Steel |
| 7 | Side Bracket | [Side bracket] | 2 | Steel |
| 8 | Base | [Base] | 2 | Steel |
| 9 | Sync Rod | [Sync rod] | 1 | Aluminum |
Accessories List
| Label | Description | Quantity |
|---|---|---|
| A | Power Cable | 1 pc |
| B | Controller | 1 pc |
| C | Leveling Studs | 4 pcs |
| D | Wire Clips | 5 pcs |
| E | 4mm Allen Key | 1 pc |
| F | 3mm Allen Key | 1 pc |
| G | Screws M6X12 | 36 pcs |
| H | Screws M5X8 | 14 pcs |
| I | Screws M6X35 | 10 pcs |
| J | Wooden Rod | 16 pcs |
| K | AC Adapter | 1 pc |
| L | Mouse-pad | 1 pc |
| M | Hook | 2 pcs |
| N | Outlet Box | 2 pcs |
| O | Iron Connector | 4 pcs |
| P | Screws M4 X 12 | 4 pcs |
| Q | Lockable wheel | 4 pcs |
| R | Type-C | 1 pc |
Notice! When the screw is tightened, do not continue to tighten it forcefully, otherwise the screw may be damaged.
Assembly Instructions
Step 1: Desktop Assembly
Description: Join the desktop pieces (1), (2), and (3) using Wooden Rods (J). 14 rods (J) are used in total.
Hardware: J x 14
Step 2: Attach Iron Connectors
Description: Attach Iron Connectors (O) to the underside of the desktop assembly. Ensure the horizontal bar of the iron connector is perpendicular to the seam of the table panel splice. Use 4mm Allen Key (E) and Screws M6X12 (G).
Hardware: E x 1, G x 16, O x 4
Step 3: Assemble Frame (Part 1)
Description: Attach Support Beams (6) to the legs. Use 4mm Allen Key (E) and Screws M5X8 (H).
Hardware: E x 1, H x 4
Step 4: Assemble Frame (Part 2)
Description: Install the second Support Beam (6) on the other side in the same way as in Step 3.
Hardware: E x 1, H x 4
Step 5: Attach Wheels and Leveling Studs
Description: Attach Lockable wheels (Q) and Leveling Studs (C) to the bases of the legs (8). Use 4mm Allen Key (E) and Screws M6X35 (I). Press the adjustment button on the wheel to brake.
Hardware: C x 4, E x 1, I x 8, Q x 4
Note: Pay attention to the direction of the Side Brackets (7) when installing.
Step 6: Attach Side Brackets and Hooks
Description: Stand the desk up. Install Side Brackets (7). Hooks (M) can be installed together with the brackets in any of the four holes according to personal habits. Use 4mm Allen Key (E) and Screws M5X8 (H).
Hardware: E x 1, H x 4, M x 2
Step 7: Install Sync Rod
Description: Insert the hexagonal rod of the sync rod into the main shaft of the leg without the motor, and lock the plastic nut. Then, insert the other side of the coupling rod into the pre-built rod on the motor leg and lock the plastic nut again. Use Circlips and Locknut. Both ends of the sync rod should be inserted tightly.
Diagram Description: Shows inserting a rod with circlips into leg shafts and securing with locknuts.
Step 8: Install Frame on Desktop
Description: Install the assembled frame onto the desktop. Use 4mm Allen Key (E) and Screws M6X12 (G).
Hardware: E x 1, G x 12
Step 9: Install Controller and AC Adapter
Description: Install the AC Adapter (K) and Controller (B) onto the desktop. Use 4mm Allen Key (E), Screws M6X12 (G), Screws M4X12 (P), and Type-C (R) cable. Wire Clips (D) are also used for tidying.
Hardware: B x 1, D x 5, E x 1, G x 6, K x 1, P x 4, R x 1
Diagram Description: Shows placement of AC adapter, controller, and routing of cables, with wire clips for tidying.
Step 10: Insert Outlet Box
Description: Stand the desk up and press the Outlet Box (N) firmly into the desk. Use Mouse-pad (L).
Hardware: L x 1, N x 2
Step 11: Connect Cables and Tidy Wires
Description: Connect the Controller (B), AC Adapter (K), and Power Cable (A) to the Left Leg. Use Wire Clips (D) to tidy up the wires.
Hardware: A x 1, B x 1, D x 5, K x 1
Diagram Description: Shows connecting the power cable, AC adapter, and controller to the leg assembly, and using wire clips to manage cables.
Controller Instruction
The controller allows for height adjustment and memory presets.
RESET Setting
To reset the desk: Press and hold the "Up" ⬆️ and "Down" ⬇️ buttons on the handset simultaneously for 4 seconds. The display will show "000". Release the buttons. The desk will move down slowly automatically (it will have a rebound and rise about 5mm) until it shows "69" and a beep is heard, indicating a successful reset.
Height Adjustment
Up: Press the "Up" button ⬆️.
Down: Press the "Down" button ⬇️.
Switch Display
Press the "Down" button ⬇️ twice when the desk is at its lowest position to switch between centimeters (cm) and inches (inch).
Memory Height
To store a height: Press and hold any of the memory buttons (1, 2, 3, or 4) until a beep is heard. Release the button. The current height is now stored. To recall a stored height: Press the corresponding memory button (1, 2, 3, or 4), and the desk will automatically adjust to that height.
Note: The standing desk has 4 different height memories. These settings are retained even after power off. You can use the up and down buttons to adjust the desk to your desired working height.
Troubleshooting Guide
- If your standing desk does not work properly, you may need to reset it.
- If any error codes appear, you need to reset it.
- If it still does not work after the reset, please contact FAREXON support for more help.
Maintenance and Consideration
- During daily maintenance, use a clean soft cloth to remove surface dust. Do not use a wet cloth or hard material to wipe the surface of the table.
- Avoid contacting the surface with acid-based chemicals.
- For slight scratches, gently wipe with a soft cloth; this can smooth out scratches. Avoid attaching tape directly to the outer surface of the metal feet to prevent paint from peeling.
