Ryobi P118 18V Dual Chemistry Battery Charger Operator's Manual
Safety Rules for Charger
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:
- That pins on plug of extension cord are the same number, size and shape as those of plug on charger.
- That extension cord is properly wired and in good electrical condition; and
- That wire size is large enough for AC ampere rating of charger as specified below:
| Cord Length (Feet) | 25' | 50' | 100' |
| Cord Size (AWG) | 16 | 16 | 16 |
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.
Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.
Do not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.
Disconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.
Risk of electric shock. Do not touch un-insulated portion of output connector or un-insulated battery terminal.
Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of the product and possible injury.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS - DANGER: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK CAREFULLY FOLLOW THESE INSTRUCTIONS. This manual contains important safety and operating instructions for battery charger P118.
- Before using battery charger, read all instructions and cautionary markings on charger, battery, and product using battery.
- NOTICE: To reduce the risk of injury, charge only nickel-cadmium or lithium-ion rechargeable batteries. Other types of batteries may burst, causing personal injury or damage.
Symbols
The following signal words and meanings are intended to explain the levels of risk associated with this product.
| SYMBOL | SIGNAL | MEANING |
| ! | DANGER: | Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. |
| ! | WARNING: | Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. |
| ! | CAUTION: | Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. |
| i | NOTICE: | (Without Safety Alert Symbol) Indicates important information not related to an injury hazard, such as a situation that may result in property damage. |
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
| SYMBOL | NAME | DESIGNATION/EXPLANATION |
| ! | Safety Alert | Indicates a potential personal injury hazard. |
| ? | Read Operator's Manual | To reduce the risk of injury, user must read and understand operator's manual before using this product. |
| ? | Eye Protection | Always wear eye protection with side shields marked to comply with ANSI Z87.1. |
| ? | Wet Conditions Alert | Do not expose to rain or use in damp locations. |
| V | Volts | Voltage |
| Hz | Hertz | Frequency (cycles per second) |
| W | Watt | Power |
| ~ | Alternating Current | Type of current |
| = | Direct Current | Type or a characteristic of current |
CALIFORNIA PROPOSITION 65
WARNING: This product contains chemicals, including lead, known to the state of California to cause birth defects and other reproductive harm. Wash hands immediately after handling.
Features
PRODUCT SPECIFICATIONS
- Battery Pack Voltage: 18 V DC
- Charger Input: 120 V, AC only, 60 Hz
- Charge Time: Approx. 1 hour (NOTE: Charge time is dependent on the type of battery pack.)
KNOW YOUR CHARGER
See Figure 1, page 9. The safe use of this product requires an understanding of the information on the product and in this operator's manual. Before use of this product, familiarize yourself with all operating features and safety rules.
CORD WRAP
The cord wrap area keeps the cord neatly in place when the charger is mounted on the wall or is being stored.
DIAGNOSTIC FEEDBACK
LEDs provide feedback to indicate whether the battery pack is charging, fully charged, or defective.
DUAL CHEMISTRY
The battery charger can charge either lithium-ion or nickel-cadmium batteries.
ENERGY SAVE MODE
Energy Star® qualified systems enter Energy Save Mode when not charging or when maintaining batteries. This allows the charger to conserve energy by charging batteries only as needed, and also protects the cells and maximizes the life of your batteries.
ENERGY STAR® QUALIFIED
This battery charger meets the Energy Star® energy-efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy. Battery chargers meeting this standard use an average of 35% less energy than conventional battery chargers.
KEY HOLE HANGER
The charger has a key hole hanging feature for convenient, space saving storage. Screws should be installed so that the center distance is 4-1/2 in.
Assembly
This product has been shipped completely assembled.
- Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.
- Inspect the product carefully to make sure no breakage or damage occurred during shipping.
- Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.
- If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
WARNING: Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled could result in serious personal injury.
WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.
WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
Operation
WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the following purpose:
- Charging compatible Ryobi 18 volt battery packs
NOTICE: If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest authorized service center for service or replacement.
NOTICE: Charge in a well-ventilated area. Do not block charger vents. Keep them clear to allow proper ventilation.
CHARGING
See Figure 2, page 9. Battery packs are shipped in a low charge condition to prevent possible problems. Therefore, you should charge them before first use. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check.
- Make sure the power supply is normal household voltage, 120 volts, AC only, 60 Hz.
- Connect the charger to a power supply.
- Attach the battery pack to the charger by aligning the raised ribs on the battery pack with the grooves in the charger, then slide the battery pack onto the charger.
- Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. Latches should snap into place to ensure charger is correctly connected.
- Do not place the charger in an area of extreme heat or cold. It will work best at normal room temperature.
- The battery pack may become slightly warm to the touch while charging. This is normal and does not indicate a problem.
- After charging is complete, the green LEDs will remain on while the charger is in Maintenance Mode.
- After completing Maintenance Mode, the green LEDs will begin fading on/off continuously. This indicates the battery is fully charged and the charger is in Energy Save Mode.
- Charger will periodically wake from Energy Save Mode to ensure the battery pack remains in a fully charged state.
- To remove the battery pack from the charger, depress latches and pull up on the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the battery pack may become hot. A hot battery pack may be placed directly onto the charger port but charging will not begin until the battery temperature cools to within acceptable temperature range. When a hot battery pack is placed on the charger, the red LED will begin flashing and the green LED will be off. When the battery pack cools, the charger will automatically begin charging.
CHARGING A COLD BATTERY PACK
A cold battery pack may be placed directly onto the charger port but charging will not begin until the battery temperature warms to within acceptable temperature range. When a cold battery pack is placed on the charger, the red LED will begin flashing and the green LED will be off. When the battery pack warms, the charger will automatically begin charging.
LED Function of Charger
See Figure 4, page 7.
| MODE | BATTERY PACK | RED LED | GREEN LED | ACTION |
| Power | Without battery pack | OFF | ON | Ready to charge battery pack. |
| Testing | Hot battery pack | ? | OFF | When battery pack reaches cooled temperature, charger begins charge mode. |
| Cold battery pack | Flashing | OFF | When battery pack reaches warmed temperature, charger begins charge mode. | |
| Deeply discharged | Flashing | ? | Charger pre-charges battery until normal voltage is reached, then begins charge mode. | |
| Defective | Defective | Fading | OFF | Battery pack or charger is defective.
|
| Charging | Charging | ON | Flashing | Battery is being charged. |
| Charged | Battery full | OFF | ON | Charging is complete; charger maintains charge mode. |
| Energy Save Mode | Battery full / Energy Save mode | OFF | Fading | Battery pack is fully charged and charger is in Energy Save mode. |
Maintenance
WARNING: When servicing use only identical replacement parts. Use of any other parts can create a hazard or cause product damage.
WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which can result in serious personal injury.
STORAGE
Always remove the battery pack before storing the charger or any time the charger is unplugged.
This product has a Three-Year Limited Warranty. Warranty details are available at www.ryobitools.com
NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 9 AFTER FRENCH AND SPANISH LANGUAGE SECTIONS
Parts and Service
Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate.
- MODEL NUMBER: P118
- SERIAL NUMBER: [Field for Serial Number]
HOW TO OBTAIN REPLACEMENT PARTS:
Replacement parts can be purchased online at www.ryobitools.com or by calling 1-800-525-2579. Replacement parts can also be obtained at one of our Authorized Service Centers.
HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
Authorized Service Centers can be located online at www.ryobitools.com or by calling 1-800-525-2579.
HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
RYOBI is a registered trademark of Ryobi Limited and is used pursuant to a license granted by Ryobi Limited.
ONE WORLD TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-800-525-2579 www.ryobitools.com • A subsidiary of Techntronic Industries Co., Ltd. • OTC:TTNDY
