HiSazo 4-Zone Digital Water Timer

What's in the Box

• 4-zone Water Timer x1
• Filter x4
• Mounting Bracket x1
• Hose Adapter x4 (EU version only)
• Teflon Tape x1
• Screw Accessories x1
• Brace x1
• User Manual x1

Overview

Diagram showing the HiSazo water timer. Key components labeled are: LCD SCREEN, WATER INLET, SETTING DIAL, ZONE BUTTON, WATER OUTLETS, OK/MANUAL BUTTON, +/DELAY BUTTON, and - BUTTON.

Important! Please Read!

• ⚠ Please activate the valve before use if it is the first time or after a period of idleness. For first-time use, to activate the timer with auto-test mode, hold the OK button without releasing and then insert batteries. The timer will automatically turn on and off the valves to test and activate. Take out the batteries and re-insert to get the timer back to work normally. (Explanation: In most cases, the valve is activated, but due to external forces or the environment during storage and transportation, the valve may appear to close on its own, then it needs to be activated manually.)
• ⚠ Only use with clean cold water.
• ⚠ The filter traps dirt particles, prolonging the life of the product. Clean the filter regularly and replace if worn.
• ⚠ When expecting freezing temperatures, timers should be removed from the hose faucet and stored indoors to avoid potential freeze damage.

Button Function Introduction

Dial Functions

Button Functions

Specification

• Four 1" or 3/4" inlets and 3/4" outlet
• Working water pressure: 0.5 bar to 8 bar (7.25-116 PSI)
• Flow rate: 22 L/min (5.8 Gal/min)
• Powered by 4xAA batteries (not included)
• IP54 waterproof

Installation

Follow these steps for installation:

1. Screw the mounting bracket on the back of the water timer.
2. Use the screw to install the brace onto the mounting bracket through the hole.
3. Install the timer on the tap and mark a proper position before installing the brace.
4. Drill a hole for screwing.
5. Attach the brace with the screw.

Final Check

Once you have completed all the necessary settings and installations, perform this final check to prepare the valve for use:

1. After screwing the timer onto the faucet, keep the tap closed and turn the dial to the ON position.
2. Hold the "-" button for at least 2 seconds for self-inspection. This will cause all four outlets to open simultaneously to check each valve.
3. Open the faucet and wait until water flows out from all four outlets.
4. Once water flows from all four outlets, turn the dial to the OFF position to close all outlets and stop self-inspection, or it will auto-off in 2 minutes.
5. The timer is now ready for use! Remember to turn the dial back to the ON position to activate your auto irrigation system!

Programming the Timer

STEP 1: SET CLOCK

Diagram shows the timer's LCD displaying time and the setting dial.

1. Turn the dial to SET CLOCK.
2. Use + and - buttons to set the hours, then press OK to confirm and set minutes. Hold buttons for 3 seconds to quickly adjust.
3. Press OK to make a final confirmation after setting minutes; everything will stop blinking. At this time, ONLY press + and - buttons to set up time again.
4. At any time during clock setup, press and hold the OK button to switch between 12H/24H time format.
5. After finishing setup, turn the dial to START TIME.

STEP 2: START TIME

Diagram shows the timer's LCD displaying zone and start time, and the setting dial.

1. Turn the dial to START TIME.
2. Use + and – buttons to set the hour of the watering start time, then press OK to confirm and set minutes. Hold buttons for 3 seconds to quickly adjust.
3. Press OK to make a final confirmation after setting minutes; everything will stop blinking. At this time, ONLY press + and - buttons to set up time again.
4. During setting, press the ZONE button to switch the zone of setting.
5. After finishing setup, turn the dial to HOW LONG.

STEP 3: HOW LONG

Diagram shows the timer's LCD displaying zone and watering duration, and the setting dial.

1. Turn the dial to HOW LONG.
2. Use + and – buttons to set the hour of the watering duration, then press OK to confirm and set minutes. Hold buttons for 3 seconds to quickly adjust.
3. Press OK to make a final confirmation after setting minutes; everything will stop blinking. At this time, ONLY press + and - buttons to set up time again.
4. The maximum watering duration can be set is 3 hours and 59 minutes. When set to 0 hour and 0 minute, the plan will not run.
5. During setting, press the ZONE button to switch the zone of setting.
6. After finishing setup, turn the dial to HOW OFTEN.

STEP 4: HOW OFTEN

Diagram shows the timer's LCD displaying zone and watering frequency, and the setting dial.

1. Turn the dial to HOW OFTEN.
2. Use + and – buttons to set watering frequency, then press OK to confirm and set minutes.
3. Press OK to make a final confirmation; everything will stop blinking. At this time, ONLY press + and - buttons to resume set up.
4. The frequency options are every 8 hours, 12 hours, and 1 to 7 days.
5. During setting, press the ZONE button to switch the zone of setting.
6. After finishing setup, turn the dial to ON to run the watering schedules.

STEP 5: AUTOMATIC WATERING

Diagram shows the timer's LCD displaying current time and next watering time, and the setting dial set to ON.

1. Turn dial to ON.
2. The LCD screen will display the current time and the next time to start watering.

CONGRATULATIONS! Your timer has now been programmed successfully. It will start watering automatically based on the programmed start time, duration, and frequency. You can keep the faucet turned on and trust the timer to do the watering!

Manual Watering

Manual Watering Mode

Diagram shows the timer's LCD displaying zone selection and the setting dial.

Manual Watering allows you to manually water without interrupting your set watering schedule. To access this feature, follow the steps below:

1. When the dial stays in ON, press and hold the OK button for 3 seconds to enter manual watering mode.
2. First, set the zone preferred for manual watering. Zone 1 will start blinking. Short press the ZONE button to switch zone options and use the OK button to select.
3. After selecting zones, hold the ZONE button to confirm and go to manual water duration setup.
4. The minute display will blink. Use + and – buttons to set time. Hold buttons for 3 seconds to quickly adjust. The default manual watering time is 10 minutes. Manual watering duration can be set from 0-6 hours.
5. Press the OK button to start manual watering at once, or leave it without any operation for 5 seconds to automatically start.
6. When manual watering, hold the OK button again to stop, or turn the dial to OFF to stop.

Note:

• Manual watering priority is greater than scheduled watering. For different zones, when the manual watering time conflicts with the scheduled watering time, the manual watering will be executed first, and the scheduled watering will start after the manual watering is finished. If there is a conflict between manual watering and scheduled watering in the same zone, manual watering will be executed first and scheduled watering will be skipped automatically.
• Zone 1, 2, 3, 4 are not executed simultaneously, but in sequence. If more than one Zone has the same start time, the Zones will be opened in order, not at the same time.

Rain Delay

Delay Mode

Diagram shows the timer's LCD displaying delay time and the setting dial.

When the dial stays in ON, press and hold the + button for 3 seconds to enter the delay mode setting. Press + and - buttons to set the delay time for 0, 24, 48, or 72 hours, and press the OK button to confirm. Select 0H to cancel the delay mode. If there is no action within 5 seconds, the delay mode will be cancelled as well. During the delay mode, hold the + button to cancel the delay.

Note:

• When a watering plan has more than one valve to run, the timer will open the valves one by one in the order of zone number, meaning the timer can only open ONE valve at a time.
• The four Zones cannot be opened at the same time; only one Zone can be opened at a time. When the start time of the four Zones is the same, priority will be given to opening one Zone. When the execution of one Zone is completed, the execution of the second Zone will begin, then the third Zone, and then the fourth Zone will begin.

More Functions

Off Mode

Diagram shows the timer's LCD displaying "OFF".

1. If you wish to stop all watering plans for an extended period, turn the dial to "OFF". Your settings are saved.
2. The timer will not water automatically while in OFF mode. The screen will display the word OFF in large letters.
3. To start watering automatically again, turn the dial back to "ON" to resume your programmed watering schedule.

Battery Status

Battery Status will be displayed as follows:

[Battery Symbol] Low Power

Note: When the low battery indicator appears on the display, the valve will close automatically to avoid leakage. Please replace the battery in time to avoid interrupting normal operation.

Trouble Shooting

Warnings

• ⚠ Intended for outdoor use only; placing it in a sheltered outdoor location will prolong the product lifetime.
• ⚠ Using tools to tighten your timer too tightly can cause damage. Tighten it with your hand instead of a tool.
• ⚠ Please ensure that the filter is placed horizontally in the top connector before installation to prevent leakage. Add a filter and thread seal tape if necessary.
• ⚠ The mesh filter prevents dirt particles, prolonging the life of the hose timer. Clean the filter regularly and replace if worn.
• ⚠ When the power is low, please replace the batteries in time to avoid interruption of normal operation. When replacing batteries, please make sure that the battery compartment is dry.
• ⚠ When not in use, remove batteries, drain the timer, and store indoors away from freezing.
• ⚠ Do not use the timer if the temperature is more than 122°F (50°C) or less than 37.4°F (3°C).
• ⚠ Do not subject the product to extreme force and shock.
• ⚠ Severe electrical shock could result if water is sprayed into outlets or sources of electrical current. Never immerse the product in water.

Warranty

HiSazo provides a 1-year warranty against manufacturing defects in materials and workmanship from the date of purchase. During the warranty period, HiSazo will replace, free of charge, any product found to be defective under reasonable use and service, as determined solely by HiSazo. To place a warranty request, please email your order ID to us, and we'll respond within 24 hours.

Customer Service

If the user manual does not contain the information you are looking for, or if you need some help, please prepare the order number of your device and contact the store before returning the product.

Manufacturer Information

INKBIRD TECH.C.L.

Email: support@inkbird.com

Factory address: 6th Floor, Building 713, Pengji Liantang Industrial Area, NO.2 Pengxing Road, Luohu District, Shenzhen, China

Office address: Room 1803, Guowei Building, NO.68 Guowei Road, Xianhu Community, Liantang, Luohu District, Shenzhen, China

[FC Logo] [CE Logo] Made in China [WEEE Symbol] [Battery Symbol] AA batteries (Not included) [Recycling Symbol]

French text regarding recycling: BARQUETTE + ÉTUI, BAC DE TRI. Cet appareil et sa batterie se recyclent. À DÉPOSER EN MAGASIN OU À DÉPOSER EN DÉCHÈTERIE. Points de collecte sur www.quefairedemesdechets.fr. Privilégiez la réparation ou le don de votre appareil !