Matchmaster - 4G/5G Ready Digital TV Antenna and Commercial Headend Specialists
Instruction Manual for Matchmaster models including: LT3195, 01MM-DG27 Digital TV Antenna, 01MM-DG27, Digital TV Antenna, TV Antenna, Antenna
Digimatch VHF/UHF X-type Colinear 27 Element Receives Band 3, 4, and 5 (Channel 6-12 and 28-46) | Jaycar Australia
File Info : application/pdf, 2 Pages, 730.46KB
DocumentDocument01MM-DG27 INSTRUCTION MANUAL A B 3) Install the two corner screens onto the top and underbody of the front 609mm boom behind the X type balun, using 3/16" x 1.75" Philips head bolts and two pre-drilled holes. Make sure you install the spring washer and wingnut on the underbody of the boom body. C D E A. 1x Front 609mm Boom B. 1x Back 714mm Boom with Joiner and Mounting Bracket C. 5x Snap On X Elements D. 1x X Type Dipole Balun E. 2x Corner Screens F. 1x G-unit with Built-in Balun 1x 1/4" x 1.25" Bolt 1x 1/4" x 18G Flat Washer 1x 1/4" Spring Washer F 1x 1/4" Wing Nut 1x 3/16" x 1.25" Philips Head Bolt 2x 3/16" x 1.75" Philips Head Bolt 3x 3/16" Spring Washer 3x 3/16" Wing Nut 1x Rubber Boot Seal 1x RG6 Twist on `F' Type Connector 1x 550mm `F' Male to `F' Male Interconnecting Flylead 4) Snap out the three riveted swivel lock elements on the back 714mm boom. 1) Snap on the five X type elements to the first five moulds located on the front 609mm boom. 5) Attach the G-unit to the back 714mm boom underbody with the balun closer to the front of the antenna, lining up the pre-drilled holes located on the G-unit and boom. Bolt these two units together using the 1/4" bolt, flat washer, spring washer and wingnut provided in the small plastic bag. Ensure you install the flat washer, spring washer and wingnut on top of the boom body. 2) Click in the X type balun to the sixth mould located on the front 609mm boom. Ensure the connection points on the X type balun face the back of the antenna. 6) Join the front 609mm boom to the back 714mm boom using the 3/16" Philips head bolt, spring washer and wingnut provided in the small plastic bag. Make sure you install the spring washer and wingnut on the underbody of the boom body. Page 1 of 2 | AU Support 1800 237 425 www.matchmaster.com.au NZ Support 0800 237 425 www.matchmaster.co.nz Modified 14 Jun 2024 7) Connect the supplied 550mm interconnecting flylead by screwing one end onto the connection of the X type balun labelled "Input". Then, connect the other end to the G-units built-in balun. Finally, twist and push the rubber boots over the connections to create a weather seal. To transmitter 8) Attach the antenna to the mast using the U-bolt and point to your nearest transmitter. Slide the rubber boot seal into your coaxial cable. Strip the coaxial cable, attach the connector provided, and connect to the antennas X type balun labelled "Output". Fix the coaxial cable down the mast using UV grade insulation tape and cable ties. Page 2 of 2 | AU Support 1800 237 425 www.matchmaster.com.au NZ Support 0800 237 425 www.matchmaster.co.nz Modified 14 Jun 2024